Tumble polishing


Tumble polishing

Tumble polishing, or tumbling, is a technique for smoothing and polishing a rough surface. Within the field of metalwork, this is known as "barreling", or "barrel polishing", and is subtly different, but uses the same principles.

tone

For tumbling of rocks as a lapidary technique, a plastic or rubber-lined barrel is loaded with a consignment of rocks, all of similar or the same hardness, some abrasive grit, and a liquid lubricant. Silicon carbide grit is commonly used, and water is a universal lubricant. The barrel is then placed upon slowly rotating rails so that it rotates. The "optimal" speed of rotation depends on the size of the tumbler barrel and materials involved.

A well-chosen speed for stone polishing causes the rocks within the barrel to slide past each other, with the abrasive grit between them. The result of this depends on the coarseness of the abrasive, and the duration of the tumble.

Typically, a full tumble polish from rough rock to polish takes around 4-5 weeks, and is done in a minimum of 4 steps. Initially, the rocks are smoothed with a coarse grit (such as 60-90 mesh), followed by washing and finer grits (120-220 then 400-600 mesh), before the (optional) use of a pre-polishing compound (1200 grit), a washing cycle with detergent to remove any grit on the stones and finally a polishing stage using powdered polish, (such as cerium oxide or tin oxide) water and often, small plastic pellets that are designed to help cushion the stones as they tumble (so as not to cause chipping) and carry the polish evenly across the stones. The precise tumbling time is determined by many factors, including the hardness of the rock and the degree of smoothing desired in the coarser steps. Some people will tumble stones with rough grit for two, three or even four weeks to get their desired shapes out of the stones.

Sometimes, stone "preforms" are used. This refers to cutting shapes from the rough rock, before tumbling. This gives more control over the final piece, so shapes such as a tear drop can be produced. The technique is still limited to rounded shapes. Preforms may use less time with the coarsest step, or skip it altogether.

During the 1970s, small rock tumblers were a common hobby item, and jewelry decorated with tumbled semi-precious stones was very much in fashion. Likewise, dishes and decorative glass jars filled with tumbled stones (often including common rocks not suitable even for costume jewelry) were frequently used as household ornaments.

Metal

Metal tumbling is used for obtaining a specified surface finish, burnishing, burr removal, cleaning, creating radii on edges, deflashing, and breaking runners off of parts in die casting. The process is similar to that explained for rock polishing. The barrel is filled with the parts that are to be polished. Vanes, typically made of rubber, run along the inside of the barrel. As the barrel turns the vanes catch and lift the parts, which eventually slide down or fall.

Tumbling is an economical finishing process because large batches of parts can be run with little or no supervision by the operator. A full cycle can take anywhere from 6 to 24 hours with the barrel turning at 20 to 38 rpm. In most cases tumbling is most efficient when the barrel is 50% full. Some processes also use a filter system to allow parts or other materials in the cylinder to be separated.

Tumbling can either be a dry, wet, and with or without media. In wet processes a compound, lubricant, or barreling soap is added to aid the finishing process, prevent rusting, and to clean parts. Media is also used to obtain the desired finished project. Media can have any level of abrasiveness and can be made of a variety of synthetic, metallic, and even organic materials. Some of the most common materials are steel ball bearings, aluminium oxide, ceramics and plastics.

Glass

Stained glass shards used for mosaic glass are also tumbled. No abrasive is used, to avoid clouding the glass; there is only water as a lubricant. The object of this tumbling is to remove the sharp edges from the glass, so that it may be handled safely. As little as 8 hours of tumbling may be sufficient for tumbled glass.

Other

Tumbling is used to polish and smooth dice for recreational use, but it has the unfortunate effect of making their sides and faces somewhat uneven and thus making the dice less than fair.

These techniques, although they take a long time, involve very little operator intervention and thus are very cheap. Small tumblers (one pound capacity) are available and inexpensive for home/hobbyist use. At the other end of the scale, professionals can use very large barrels to do a lot of work at once. The main disadvantage of tumbling is its limited scope - stones will be smooth and have semi-random shapes (like pebbles from the beach), and metals need to be relatively simple shapes, with no fine work.

ee also

* Ball mill, a process with some similarities to tumble polishing
* Stone carving

References


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Polishing — is the process of creating a smooth and shiny surface by using rubbing or a chemical action, leaving a surface with significant specular reflection and minimal diffuse reflection. Imagine the surface magnified thousands of times, it usually looks …   Wikipedia

  • Rock polishing — is a lapidary process whereby rough stone is polished and smoothed using simple machines to produce attractive stones. The most common means is tumble polishing, but there is also vibratory finishing …   Wikipedia

  • Tumbler — may refer to:* A part of a lock whose position must be changed by a key in order to release the bolt (see also: pin tumbler lock, tubular pin tumbler lock, and disc tumbler lock) * Flat bottomed glassware and drinkware without a handle, foot, or… …   Wikipedia

  • Industrial process — Industrial processes are procedures involving chemical or mechanical steps to aid in the manufacture of an item or items, usually carried out on a very large scale.Industrial processes are the key components of heavy industry.Most processes make… …   Wikipedia

  • Vibratory finishing — is a process used to remove burrs from large numbers of relatively small workpieces.In this batch type operation, specially shaped abrasive pellets of nonmetallic or metallic media are placed in a Vibratory tumbler along with the parts to be… …   Wikipedia

  • Tumbling — may refer to:* Tumbling (gymnastics), floor gymnastics similar to somersault, back handsprings, and roundoffs * Tumble polishingee also* Tumbler …   Wikipedia

  • Surface finishing — is a broad range of industrial processes that alter the surface of a manufactured item to achieve a certain property.[1] Finishing processes may be employed to: improve appearance, adhesion or wettability, solderability, corrosion resistance,… …   Wikipedia

  • Mass finishing — is a group of manufacturing processes that allow large quantities of parts to be simultaneously finished. The goal of this type of finishing is to burnish, deburr, clean, radius, de flash, descale, remove rust, polish, brighten, surface harden,… …   Wikipedia

  • textile — /teks tuyl, til/, n. 1. any cloth or goods produced by weaving, knitting, or felting. 2. a material, as a fiber or yarn, used in or suitable for weaving: Glass can be used as a textile. adj. 3. woven or capable of being woven: textile fabrics. 4 …   Universalium

  • Cylinder head porting — refers to the process of modifying the intake and exhaust ports of an internal combustion engine to improve the quality and quantity of the air flow. Cylinder heads, as manufactured, are usually suboptimal due to design and manufacturing… …   Wikipedia