- Interference lithography
Interference lithography (or holographic lithography) is a technique for patterning regular arrays of fine features, without the use of complex optical systems or
The basic principle is the same as in
interferometryor holography. An interference pattern between two or more coherent light waves is set up and recorded in a recording layer ( photoresist). This interference pattern consists of a periodic series of fringes representing intensity minima and maxima. Upon post-exposure photolithographic processing, a photoresist pattern corresponding to the periodic intensity pattern emerges.
For 2-beam interference, the fringe-to-fringe spacing or period is given by (λ/2)/sin(θ/2), where λ is the wavelength and θ is the angle between the two interfering waves. The minimum period achievable is then half the wavelength.
By using 3-beam interference, arrays with hexagonal symmetry can be generated, while with 4 beams, arrays with rectangular symmetry are generated. Hence, by superimposing different beam combinations, different patterns are made possible.
For interference lithography to be successful, coherence requirements must be met. First, a spatially coherent light source must be used. This is effectively a point light source in combination with a collimating lens. A laser or synchrotron beam are also often used directly without additional collimation. The spatial coherence guarantees a uniform wavefront prior to beam splitting. Second, it is preferred to use a monochromatic or temporally coherent light source. This is readily achieved with a laser but broadband sources would require a filter. The monochromatic requirement can be lifted if a diffraction grating is used as a beam splitter, since different wavelengths would diffract into different angles but eventually recombine anyway. Even in this case, spatial coherence and normal incidence would still be required.
Electron holographic lithography
The technique is readily extendible to electron waves as well, as demonstrated by the practice of
electron holography[1,2] . Spacings of a few nanometers  or even less than a nanometer  have been reported using electron holograms. This is because the wavelength of an electron is always shorter than for a photon of the same energy. The wavelength of an electron is given by the deBroglie relation h/p, where h is the Planck constantand p is the electron momentum. For example, a 1 keVelectron has a wavelength of slightly less than 0.04 nm. A 5 eVelectron has a wavelength of 0.55 nm. This yields X-ray-like resolution without depositing significant energy. In order to ensure against charging, it must be ensured that electrons can penetrate sufficiently to reach the conducting substrate.
A fundamental concern for using low-energy electrons (<<100 eV) with this technique is their natural tendency to repel one another due to Coulomb forces as well as
Fermi-Dirac statistics, though electron anti-bunching has been verified only in a single case.
Atom holographic lithography
The interference of atomic deBroglie waves is also possible provided one can obtain coherent beams of cooled atoms. The momentum of an atom is even larger than for electrons or photons, allowing even smaller wavelengths, per the deBroglie relation. Generally the wavelength will be smaller than the diameter of the atom itself.
Uses of interference lithography
The benefit of using interference lithography is the quick generation of dense features over a wide area without loss of focus. Hence, it is commonly used for testing photoresist processes for lithography techniques based on new wavelengths (e.g., EUV or 193 nm immersion). Electron interference lithography [3,4] may be used for patterns which normally take too long for conventional
electron beam lithographyto generate.
The drawback of interference lithography is that it is limited to patterning arrayed features only. Hence, for drawing arbitrarily shaped patterns, other photolithography techniques are required. In addition, non-optical effects, such as secondary electrons from
ionizing radiationor photoacid generation and diffusion, cannot be avoided with interference lithography. For instance, the secondary electron range is roughly indicated by the width of carbon contamination (~20 nm) at the surface induced by a focused (2 nm) electron beam  . This indicates that the lithographic patterning of 20 nm half-pitch features or smaller will be significantly affected by factors other than the interference pattern, such as the cleanliness of the vacuum.
# R. E. Dunin-Borkowski et al., Microsc. Res. Tech. vol. 64, pp. 390-402 (2004).
# F. Hasselbach, Scanning Microscopy, vol. 11, pp. 345-366 (1997).
# K. Ogai et al., Appl. Phys. Lett., vol. 66, pp. 1560-1562 (1995).
# S. Fujita et al., Appl. Phys. Lett., vol. 66, pp. 2754-2756 (1995).
Wikimedia Foundation. 2010.
Look at other dictionaries:
Lithography — Charles Marion Russell s The Custer Fight (1903). Note the range of tones, fading toward the edges … Wikipedia
Interference (wave propagation) — Two point interference in a ripple tank. In physics, interference is the phenomenon in which two waves superpose each other to form a resultant wave of greater or lower amplitude. Interference usually refers to the interaction of waves that are… … Wikipedia
Extreme ultraviolet lithography — (also known as EUV or EUVL ) is a next generation lithography technology using the 13.5 nm EUV wavelength. EUVL opticsEUVL is a significant departure from the deep ultraviolet lithography used today. All matter absorbs EUV radiation. Hence, EUV… … Wikipedia
Electron beam lithography — (often abbreviated as e beam lithography) is the practice of scanning a beam of electrons in a patterned fashion across a surface covered with a film (called the resist),cite book |last= McCord |first=M. A. |coauthors=M. J. Rooks |title=… … Wikipedia
Maskless lithography — In maskless lithography, the radiation that is used to expose a photosensitive emulsion (or photoresist) is not projected from, or transmitted through, a photomask. Instead, most commonly, the radiation is focused to a narrow beam. The beam is … Wikipedia
Contact lithography — Contact lithography, also known as contact printing, is a form of photolithography whereby the image to be printed is obtained by illumination of a photomask in direct contact with a substrate coated with an imaging photoresist layer. Contents 1… … Wikipedia
Computational lithography — (also known as computational scaling) is the set of mathematical and algorithmic approaches designed to improve the resolution attainable through photolithography. Computational lithography has come to the forefront of photolithography in 2008 as … Wikipedia
Immersion lithography — is a photolithography resolution enhancement technique that replaces the usual air gap between the final lens and the wafer surface with a liquid medium that has a refractive index greater than one. The resolution is increased by a factor equal… … Wikipedia
Photonic metamaterial — Electromagnetism Electricity · … Wikipedia
Superlens — A superlens, super lens or perfect lens is a lens which uses metamaterials to go beyond the diffraction limit. The diffraction limit is an inherent limitation in conventional optical devices or lenses. In 2000, a type of lens was proposed,… … Wikipedia