Wood drying

Wood drying

Wood drying (also seasoning lumber or timber seasoning) refers to reducing the moisture content of wood prior to its use.

For some purposes wood is not dried at all (it is used "green") [http://en.wikipedia.org/wiki/Green_wood] . Often the wood needs to be in an equilibrium with the air outside (e.g. construction wood) or the air indoors (e.g. for furniture).Wood is either air-dried or kiln-dried. Usually the wood is sawn prior to the drying process, but not always (i.e. drying the whole log)

Types of wood

Wood is divided, according to its botanical origin, into two kinds: Softwoods from coniferous trees and hardwoods from broadleaved trees. Structurally softwoods are generally simple in structure and lighter whereas hardwoods are generally complex in structure and harder.

Softwood (like pine wood) is much lighter and easier to process than the heavy hardwood (like fruit tree wood). The density of softwoods ranges between 350-700 kg/m³, while hardwoods are 450-1250 kg/m³. Both consist of approximately 12 % moisture ("Desch and Dinwoodie, 1996"). Due to the more dense and complex structure of hardwood, the permeability is very low in comparison to softwood, thus making it more difficult to dry. Even though there are about hundred times more species of hardwood trees than softwood trees, the ability to process and dry softwood much more easy and faster makes it the main supply of commercial wood today.

Wood-water relationships

The timber of living trees and freshly felled logs contains a large amount of water, which often constitutes more weight than the actual wood. Water has a significant influence on wood: wood continually exchanges moisture (water) with its surroundings, although the rate of exchange is strongly affected by the degree wood is sealed.

Water in wood may be present in two forms:
# Free water: The bulk of water contained in the cell lumina is only held by capillary forces: it is not bound chemically and is termed free water. Free water is not in the same thermodynamic state as liquid water: energy is required to overcome the capillary forces. Furthermore, free water may contain chemicals, altering the drying characteristics.
# Bound or hygroscopic water: Bound water is bound to the wood via hydrogen bonds. The attraction of wood for water arises from the presence of free hydroxyl (OH) groups in the cellulose, hemicelluloses and lignin molecules in the cell wall. The hydroxyl groups are negatively charged electrically. Water is a polar liquid. The free hydroxyl groups in cellulose attract and hold water by hydrogen bonding.

Water in cell lumina may be in the form of water vapour, but the total amount is normally negligible, at normal temperatures and moisture contents. Fact|date=March 2007

Moisture content of wood

The moisture content of wood is calculated by the formula (Siau, 1984)::m_g-m_{od} over m_{od} (1.1)Here, m_g; is the green mass of the wood, m_{od} ; is its oven-dry mass (the attainment of constant mass generally after drying in an oven set at 103 +/- 2 °C for 24 hours as mentioned by Walker "et al.", 1993). This can also be expressed as a fraction of the mass of the water and the mass of the oven-dry wood rather than a percentage, for example, 0.59 kg/kg (oven dry basis) expresses the same moisture content as 59% (oven dry basis).

Fibre saturation point

When green wood dries, the first water to go is the free water from the cell lumina. It is held only by the capillary forces. Most physical properties, such as strength and shrinkage, are unaffected by the removal of free water. The fibre saturation point (FSP) is defined as the moisture content at which free water should be completely gone, while the cell walls are saturated with bound water. In most woods, the fibre saturation point is at 25 to 30% moisture content. Siau (1984) reported that the fibre saturation point X_{fsp} ; (kg/kg) is dependent on the temperature T (°C) according to the following equation::X_{fsp} = 0.30 - 0.001 (T-20) ; (1.2)

Keey "et al." (2000) use a different definition of the fibre saturation point (equilibrium moisture content of wood in an environment of 99% relative humidity).

Many important properties of wood show a considerable change as the wood is dried below the fibre saturation point. These include:
# Volume: ideally no shrinkage occurs until some bound water is lost, i.e. until the wood is dried below FSP.
# Most strength properties show a consistent increase as the wood is dried below the FSP (Desch and Dinwoodie, 1996). An exception is impact bending strength and, in some cases toughness.
# Electrical resistivity increases very rapidly with the loss of bound water when the wood dries below the FSP.

Equilibrium moisture content

Wood is a hygroscopic substance. It has the ability to take in or give off moisture in the form of vapour. The water contained in wood exerts a vapour pressure of its own, which is determined by the maximum size of the capillaries filled with water at any time. If the water vapour pressure in the ambient space is lower than the vapour pressure within wood, desorption takes place. The largest sized capillaries, which are full of water at the time, empty first. The vapour pressure within the wood falls as water is successively contained in smaller and smaller sized capillaries. A stage is eventually reached when the vapour pressure within the wood equals the vapour pressure in the ambient space above the wood, and further desorption ceases. The amount of moisture that remains in the wood at this stage is in equilibrium with the water vapour pressure in the ambient space, and is termed the equilibrium moisture content or EMC (Siau, 1984). Because of its hygroscopicity, wood tends to reach a moisture content that is in equilibrium with the relative humidity and temperature of the surrounding air.The EMC of wood varies with the ambient relative humidity (a function of temperature) significantly, to a lesser degree with the temperature. Siau (1984) reported that the EMC also varies very slightly with species, mechanical stress, drying history of wood, density, extractives content and the direction of sorption in which the moisture change takes place (i.e. adsorption or desorption).

Moisture content of wood in service

Wood retains its hygroscopic characteristics after it is put into use. It is then subjected to fluctuating humidity, the dominant factor in determining its EMC. These fluctuations may be more or less cyclical, such as diurnal changes or annual seasonal changes.In order to minimise the changes in wood moisture content or the movement of wooden objects in service, wood is usually dried to a moisture content that is close to the average EMC conditions to which it will be exposed. These conditions vary for interior uses compared with exterior uses in a given geographic location. For example, according to the Australian Standard for Timber Drying Quality (AS/NZS 4787, 2001), the EMC is recommended to be 10-12% for the majority of Australian states, although extreme cases may be up to 15 to 18% for some places in Queensland, Northern Territory, Western Australia and Tasmania. However, the EMC may be as low as 6 to 7% in dry centrally heated houses and offices or in permanently air-conditioned buildings.

The primary reason for drying wood to a moisture content equivalent to its mean EMC under use conditions is to minimise the dimensional changes (or movement) in the final product.

hrinkage and swelling

Shrinkage and swelling may occur in wood when the moisture content is changed (Stamm, 1964). Shrinkage occurs as moisture content decreases, while swelling takes place when it increases. Volume change is not equal in all directions. The greatest dimensional change occurs in a direction tangential to the growth rings. Shrinkage from the pith outwards, or radially, is usually considerably less than tangential shrinkage, while longitudinal (along the grain) shrinkage is so slight as to be usually neglected. The longitudinal shrinkage is 0.1 to 0.3%, in contrast to transverse shrinkages, which is 2-10%. Tangential shrinkage is often about twice as great as in the radial direction, although in some species it may be as much as five times as great. The shrinkage is about 5 to 10% in the tangential direction and about 2 to 6% in the radial direction (Walker "et al.", 1993).

Differential transverse shrinkage of wood is related to:
# the alternation of late wood and early wood increments within the annual ring;
# the influence of wood rays in the radial direction (Kollmann and Cote, 1968)
# the features of the cell wall structure such as microfibril angle modifications and pits; and,
# the chemical composition of the middle lamella.

Wood drying

Wood drying may be described as the art of ensuring that gross dimensional changes through shrinkage are confined to the drying process. Ideally, wood is dried to that equilibrium moisture content as will later (in service) be attained by the wood. Thus, further dimensional change will be kept to a minimum.

It is probably impossible to completely eliminate movement in wood, but this may be approximated by chemical modification. This is the treatment of wood with chemicals to replace the hydroxyl groups with other hydrophobic functional groups of modifying agents (Stamm, 1964). Among all the existing processes, wood modification with acetic anhydride has considerable promise due to the high anti-shrink or anti-swell efficiency (ASE) attainable without damaging the wood properties. However, acetylation of wood has been slow to be commercialised due to the cost, corrosion and the entrapment of the acetic acid in wood. There is extensive literature relating to the chemical modification of wood (Rowell, 1983, 1991; Kumar, 1994; Haque, 1997).

Drying timber is one approach for adding value to sawn products from the primary wood processing industries. According to the Australian Forest and Wood Products Research and Development Corporation (FWPRDC), green sawn hardwood, which is sold at about $350 per cubic metre or less, increases in value to $2,000 per cubic metre or more with drying and processing. However, currently-used conventional drying processes often result in significant quality problems from cracks, both externally and internally, reducing the value of the product. As an example, in Queensland alone (Anon, 1997), assuming that 10% of the dried softwood is devalued by $200 per cubic metre because of drying defects, sawmillers are losing about $5 million per year in that State alone. Australia wide this could be $40 million per year for softwood and an equal or higher amount for hardwood. Thus proper drying under controlled conditions (prior to use) is of great importance in timber utilisation in any country, where climatic conditions vary considerably at different times of the year.

Drying, if carried out promptly after the felling of trees, also protects timber against primary decay, fungal stain and attack by certain kinds of insects. Organisms, which cause decay and stain, generally cannot thrive in timber with a moisture content below 20%. Several, though not all, insect pests can live only in green timber. Dried wood is less susceptible to decay than green wood (above 20% moisture content).

Apart from the above important advantages of drying timber, the following points are also significant (Walker "et al.", 1993; Desch and Dinwoodie, 1996):
# Dried timber is lighter, and hence the transportation and handling costs are reduced.
# Dried timber is stronger than green timber in most strength properties.
# Timbers for impregnation with preservatives have to be properly dried if proper penetration is to be accomplished, particularly in the case of oil-type preservatives.
# In the field of chemical modification of wood and wood products, the material should be dried to a certain moisture content for the appropriate reactions to occur.
# Dry wood works, machines, finishes and glues better than green timber. Paints and finishes last longer on dry timber.
# The electrical and thermal insulation properties of wood are improved by drying.

Prompt drying of wood immediately after felling therefore results in significant upgrading of, and value adding to, the raw timber. Drying enables substantial long term economy in timber utilisation by rationalising the utilisation of timber resources. The drying of wood is thus an area for research and development, which concerns many researchers and timber companies around the world.

How wood dries: the mechanisms of moisture movement

Water in wood normally moves from zones of higher to zones of lower moisture content (Walker "et al.", 1993). In simple terms, this means that drying starts from the outside and moves towards the centre, and it also means that drying at the outside is also necessary to expel moisture from the inner zones of the wood. Wood, after a period of time, attains a moisture content in equilibrium with the surrounding air (the EMC, as mentioned earlier).

Mechanisms for moisture movement

Moisture passageways

The basic driving force for moisture movement is chemical potential. However, it is not always straightforward to relate chemical potential in wood to commonly observable variables, such as temperature and moisture content (Keey "et al.", 2000). Moisture in wood moves within the wood as liquid or vapour through several types of passageways depending on the nature of the driving force, (e.g. pressure or moisture gradient), and variations in wood structure (Langrish and Walker, 1993), as explained in the next section on driving forces for moisture movement. These pathways consist of cavities of the vessels, fibres, ray cells, pit chambers and their pit membrane openings, intercellular spaces and transitory cell wall passageways. Movement of water takes place in these passageways in any direction, longitudinally in the cells, as well as laterally from cell to cell until it reaches the lateral drying surfaces of the wood. The higher longitudinal permeability of sapwood of hardwood is generally caused by the presence of vessels. The lateral permeability and transverse flow is often very low in hardwoods. The vessels in hardwoods are sometimes blocked by the presence of tyloses and/or by secreting gums and resins in some other species, as mentioned earlier. The presence of gum veins, the formation of which is often a result of natural protective response of trees to injury, is commonly observed on the surface of sawn boards of most eucalypts. Despite the generally higher volume fraction of rays in hardwoods (typically 15% of wood volume), the rays are not particularly effective in radial flow, nor are the pits on the radial surfaces of fibres effective in tangential flow (Langrish and Walker, 1993).

Moisture movement space

The available space for air and moisture in wood depends on the density and porosity of wood. Porosity is the volume fraction of void space in a solid. The porosity is reported to be 1.2 to 4.6% of dry volume of wood cell wall (Siau, 1984). On the other hand, permeability is a measure of the ease with which fluids are transported through a porous solid under the influence of some driving forces, e.g. capillary pressure gradient or moisture gradient. It is clear that solids must be porous to be permeable, but it does not necessarily follow that all porous bodies are permeable. Permeability can only exist if the void spaces are interconnected by openings. For example, a hardwood may be permeable because there is intervessel pitting with openings in the membranes (Keey "et al.", 2000). If these membranes are occluded or encrusted, or if the pits are aspirated, the wood assumes a closed-cell structure and may be virtually impermeable. The density is also important for impermeable hardwoods because more cell-wall material is traversed per unit distance, which offers increased resistance to diffusion (Keey "et al.", 2000). Hence lighter woods, in general, dry more rapidly than do the heavier woods. The transport of fluids is often bulk flow (momentum transfer) for permeable softwoods at high temperature while diffusion occurs for impermeable hardwoods (Siau, 1984). These mechanisms are discussed below.

Driving forces for moisture movement

Three main driving forces used in different version of diffusion models are moisture content, the partial pressure of water vapour, and the chemical potential (Skaar, 1988; Keey "et al.", 2000). These are discussed here, including capillary action, which is a mechanism for free water transport in permeable softwoods. Total pressure difference is the driving force during wood vacuum drying.

Capillary action

Capillary forces determine the movements (or absence of movement) of free water. It is due to both adhesion and cohesion. Adhesion is the attraction between water to other substances and cohesion is the attraction of the molecules in water to each other.

As wood dries, evaporation of water from the surface sets up capillary forces that exert a pull on the free water in the zones of wood beneath the surfaces. When there is no longer any free water in the wood capillary forces are no longer of importance.

Moisture content differences

The chemical potential is explained here since it is the true driving force for the transport of water in both liquid and vapour phases in wood (Siau, 1984). The Gibbs free energy per mole of substance is usually expressed as the chemical potential (Skaar, 1988). The chemical potential of unsaturated air or wood below the fibre saturation point influences the drying of wood. Equilibrium will occur at the equilibrium moisture content (as defined earlier) of wood when the chemical potential of the wood becomes equal to that of the surrounding air. The chemical potential of sorbed water is a function of wood moisture content. Therefore, a gradient of wood moisture content (between surface and centre), or more specifically of activity, is accompanied by a gradient of chemical potential under isothermal conditions. Moisture will redistribute itself throughout the wood until the chemical potential is uniform throughout, resulting in a zero potential gradient at equilibrium (Skaar, 1988). The flux of moisture attempting to achieve the equilibrium state is assumed to be proportional to the difference in chemical potential, and inversely proportional to the path length over which the potential difference acts (Keey "et al.", 2000).

The gradient in chemical potential is related to the moisture content gradient as explained in above equations (Keey "et al.", 2000). The diffusion model using moisture content gradient as a driving force was applied successfully by Wu (1989) and Doe "et al." (1994). Though the agreement between the moisture-content profiles predicted by the diffusion model based on moisture-content gradients is better at lower moisture contents than at higher ones, there is no evidence to suggest that there are significantly different moisture-transport mechanisms operating at higher moisture contents for this timber. Their observations are consistent with a transport process that is driven by the total concentration of water. The diffusion model is used for this thesis based on this empirical evidence that the moisture-content gradient is a driving force for drying this type of impermeable timber.

Differences in moisture content between the surface and the centre (gradient, the chemical potential difference between interface and bulk) move the bound water through the small passageways in the cell wall by diffusion. In comparison with capillary movement, diffusion is a slow process. Diffusion is the generally suggested mechanism for the drying of impermeable hardwoods (Keey "et al.", 2000). Furthermore, moisture migrates slowly due to the fact that extractives plug the small cell wall openings in the heartwood. This is why sapwood generally dries faster than heartwood under the same drying conditions.

Moisture movement directions for diffusion

It is reported that the ratio of the longitudinal to the transverse (radial and tangential) diffusion rates for wood ranges from about 100 at a moisture content of 5% to 2 to 4 at a moisture content of 25% (Langrish and Walker, 1993). Radial diffusion is somewhat faster than tangential diffusion. Although longitudinal diffusion is most rapid, it is of practical importance only when short pieces are dried. Generally the timber boards are much longer than in width or thickness. For example, a typical size of a green board used for this research was 6 m long, 250 mm in width and 43 mm in thickness. If the boards are quartersawn (sawing around the pith), then the width will be in the radial direction whereas the thickness will be in tangential direction, and vice versa for back-sawn (sawing through and through) boards. Most of the moisture is removed from wood by lateral movement during drying.

Reasons for splits and cracks during timber drying and their control

The chief difficulty experienced in the drying of timber is the tendency of its outer layers to dry out more rapidly than the interior ones. If these layers are allowed to dry much below the fibre saturation point while the interior is still saturated, stresses (called drying stresses) are set up because the shrinkage of the outer layers is restricted by the wet interior (Keey "et al.", 2000). Rupture in the wood tissues occurs, and consequently splits and cracks occur if these stresses across the grain exceed the strength across the grain (fibre to fibre bonding).

The successful control of drying defects in a drying process consists in maintaining a balance between the rate of evaporation of moisture from the surface and the rate of outward movement of moisture from the interior of the wood. The way in which drying can be controlled will now be explained.

Influence of temperature, relative humidity and rate of air circulation

The external drying conditions (temperature, relative humidity and air velocity) control the external boundary conditions for drying, and hence the drying rate, as well as affecting the rate of internal moisture movement. The drying rate is affected by external drying conditions (Walker "et al.", 1993; Keey "et al.", 2000), as will now be described.

Temperature: If the relative humidity is kept constant, the higher the temperature, the higher the drying rate. Temperature influences the drying rate by increasing the moisture holding capacity of the air, as well as by accelerating the diffusion rate of moisture through the wood.The actual temperature in a drying kiln is the dry-bulb temperature (usually denoted by Tg), which is the temperature of a vapour-gas mixture determined by inserting a thermometer with a dry bulb. On the other hand, the wet-bulb temperature (TW) is defined as the temperature reached by a small amount of liquid evaporating in a large amount of an unsaturated air-vapour mixture. The temperature sensing element of this thermometer is kept moist with a porous fabric sleeve (cloth) usually put in a reservoir of clean water. A minimum air flow of 2 m/s is needed to prevent a zone of stagnant damp air formation around the sleeve (Walker "et al.", 1993). Since air passes over the wet sleeve, water is evaporated and cools the wet-bulb thermometer. The difference between the dry-bulb and wet-bulb temperatures, the wet-bulb depression, is used to determine the relative humidity from a standard hygrometric chart (Walker "et al.", 1993). A higher difference between the dry-bulb and wet-bulb temperatures indicates a lower relative humidity. For example, if the dry-bulb temperature is 100 °C and wet-bulb temperature 60 °C, then the relative humidity is read as 17% from a hygrometric chart.

Relative humidity: The relative humidity of air is defined as the partial pressure of water vapour divided by the saturated vapour pressure at the same temperature and total pressure (Siau, 1984). If the temperature is kept constant, lower relative humidities result in higher drying rates due to the increased moisture gradient in wood, resulting from the reduction of the moisture content in the surface layers when the relative humidity of air is reduced. The relative humidity is usually expressed on a percentage basis. For drying, the other essential parameter related to relative humidity is the absolute humidity, which is the mass of water vapour per unit mass of dry air (kg of water per kg of dry air). The following equation can be used to calculate the absolute humidity from the relative humidity (Strumillo and Kudra, 1986):

Air circulation rate: Drying time and timber quality depend on the air velocity and its uniform circulation. At a constant temperature and relative humidity, the highest possible drying rate is obtained by rapid circulation of air across the surface of wood, giving rapid removal of moisture evaporating from the wood. However, a higher drying rate is not always desirable, particularly for impermeable hardwoods, because higher drying rates develop greater stresses that may cause the timber to crack or distort. At very low fan speeds, less than 1 m s-1, the air flow through the stack is often laminar flow, and the heat transfer between the timber surface and the moving air stream is not particularly effective (Walker "et al.", 1993). The low effectiveness (externally) of heat transfer is not necessarily a problem if internal moisture movement is the key limitation to the movement of moisture, as it is for most hardwoods (Pordage and Langrish, 1999).

Classification of timbers for drying

The timbers are classified as follows according to their ease of drying and their proneness to drying degrade:

A. Highly refractory woods: These woods are slow and difficult to dry if the final product is to be free from defects, particularly cracks and splits. Examples are heavy structural timbers with high density such as ironbark ("Eucalyptus paniculata"), blackbutt ("E. pilularis"), southern blue gum ("E. globulus") and brush box ("Lophostemon cofertus"). They require considerable protection and care against rapid drying conditions for the best results (Bootle, 1994).

B. Moderately refractory woods: These timbers show a moderate tendency to crack and split during seasoning. They can be seasoned free from defects with moderately rapid drying conditions (i.e. a maximum dry-bulb temperature of 85 °C can be used). Examples are Sydney blue gum ("E. saligna") and other timbers of medium density (Bootle, 1994), which are potentially suitable for furniture.

C. Non-refractory woods: These woods can be rapidly seasoned to be free from defects even by applying high temperatures (dry-bulb temperatures of more than 100 °C) in industrial kilns. If not dried rapidly, they may develop discolouration (blue stain) and mould on the surface. Examples are softwoods and low density timbers such as "Pinus radiata".

Methods of drying timber

Broadly, there are two methods by which timber can be dried: (i) natural drying or air drying, and (ii) artificial drying.

Air drying

Air drying is the drying of timber by exposing it to the air. The technique of air drying consists mainly of making a stack of sawn timber (with the layers of boards separated by stickers) on raised foundations, in a clean, cool, dry and shady place. Rate of drying largely depends on climatic conditions, and on the air movement (exposure to the wind). For successful air drying, a continuous and uniform flow of air throughout the pile of the timber needs to be arranged (Desch and Dinwoodie, 1996). The rate of loss of moisture can be controlled by coating the planks with any substance that is relatively impermeable to moisture; ordinary mineral oil is usually quite effective. Coating the ends of logs with oil or thick paint, improves their quality upon drying. Wrapping planks or logs in materials which will allow some movement of moisture, generally works very well provided the wood is first treated against fungal infection by coating in petrol/gasoline or oil. Mineral oil will generally not soak in more than 1-2 mm below the surface and is easily removed by planing when the timber is suitably dry.

Kiln drying

The process of kiln drying consists basically of introducing heat. This may be directly, using natural gas and/or electricity or indirectly, through steam-heated heat exchangers, although solar energy is also possible. In the process, deliberate control of temperature, relative humidity and air circulation is provided to give conditions at various stages (moisture contents or times) of drying the timber to achieve effective drying. For this purpose, the timber is stacked in chambers, called wood drying kilns, which are fitted with equipment for manipulation and control of the temperature and the relative humidity of the drying air and its circulation rate through the timber stack (Walker "et al.", 1993; Desch and Dinwoodie, 1996).

Kiln drying provides a means of overcoming the limitations imposed by erratic weather conditions. In kiln drying as in air drying, unsaturated air is used as the drying medium. Almost all commercial timbers of the world are dried in industrial kilns. A comparison of air drying, conventional kiln and solar drying is given below:
# Timber can be dried to any desired low moisture content by conventional or solar kiln drying, but in air drying, moisture contents of less than 18% are difficult to attain for most locations.
# The drying times are considerably less in conventional kiln drying than in solar kiln drying, followed by air drying.
## This means that if capital outlay is involved, this capital is just sitting there for a longer time when air drying is used. On the other hand, installing an industrial kiln, to say nothing of maintenance and operation, is expensive.
## In addition, wood that is being air dried takes up space, which could also cost money.
# In air drying, there is little control over the drying elements, so drying degrade cannot be controlled.
# The temperatures employed in kiln drying typically kill all the fungi and insects in the wood if a maximum dry-bulb temperature of above 60 °C is used for the drying schedule. This is not guaranteed in air drying.
# If air drying is done improperly (exposed to the sun), the rate of drying may be overly rapid in the dry summer months, causing cracking and splitting, and too slow during the cold winter months.

The significant advantages of conventional kiln drying include higher throughput and better control of the final moisture content. Conventional kiln and solar drying both enable wood to be dried to any moisture content regardless of weather conditions. For most large-scale drying operations solar and conventional kiln drying are more efficient than air drying.

Compartment-type kilns are most commonly used in timber companies. A compartment kiln is filled with a static batch of timber through which air is circulated. In these types of kiln, the timber remains stationary. The drying conditions are successively varied from time to time in such a way that the kilns provide control over the entire charge of timber being dried. This drying method is well suited to the needs of timber companies, which have to dry timbers of varied species and thickness, including refractory hardwoods that are more liable than other species to check and split.

The main elements of kiln drying are described below:a) Construction materials: The kiln chambers are generally built of brick masonry, or hollow cement-concrete slabs. Sheet metal or prefabricated aluminium in a double-walled construction with sandwiched thermal insulation, such as glass wool or polyurethane foams, are materials that are also used in some modern kilns. Some of the elements used in kiln construction. However, brick masonry chambers, with lime and (mortar) plaster on the inside and painted with impermeable coatings, are used widely and have been found to be satisfactory for many applications.b) Heating: Heating is usually carried out by steam heat exchangers and pipes of various configurations (e.g. plain, or finned (transverse or longitudinal) tubes) or by large flue pipes through which hot gases from a wood burning furnace are passed. Only occasionally is electricity or gas employed for heating.c) Humidification: Humidification is commonly accomplished by introducing live steam into the kiln through a steam spray pipe. In order to limit and control the humidity of the air when large quantities of moisture are being rapidly evaporated from the timber, there is normally a provision for ventilation of the chamber in all types of kilns.d) Air circulation: Air circulation is the means for carrying the heat to and the moisture away from all parts of a load. Forced circulation kilns are most common, where the air is circulated by means of fans or blowers, which may be installed outside the kiln chamber (external fan kiln) or inside it (internal fan kiln). Throughout the process, it is necessary to keep close control of the moisture content using a moisture meter system in order to reduce over-drying and allow operators to know when to pull the charge. [ [http://www.wwwagner.com/mc4000.php Wagner Moisture Meters - MC4000 Advanced In-Kiln Moisture Measurement System ] ] Preferably, this in-kiln moisture meter will have an auto-shutoff feature.

Kiln drying schedules

Satisfactory kiln drying can usually be accomplished by regulating the temperature and humidity of the circulating air to suit the state of the timber at any given time. This condition is achieved by applying kiln-drying schedules. The desired objective of an appropriate schedule is to ensure drying timber at the fastest possible rate without causing objectionable degrade. The following factors have a considerable bearing on the schedules.

# The species; because of the variations in physical, mechanical and transport properties between species.
# The thickness of the timber; because the drying time is approximately inversely related to thickness and, to some extent, is also influenced by the width of the timber.
# Whether the timber boards are quarter-sawn, back-sawn or mixed-sawn; because sawing pattern influences the distortion due to shrinkage anisotropy.
# Permissible drying degrade; because aggressive drying schedules can cause timber to crack and distort.
# Intended use of timber; because the required appearance of the timber surface and the target final moisture contents are different depending on the uses of timber.Considering each of the factors, no one schedule is necessarily appropriate, even for similar loads of the same species. This is why there is so much timber drying research, including this work, focused on the development of effective drying schedules.

Drying defects

Drying defects are the most common form of degrade in timber, next to natural problems such as knots (Desch and Dinwoodie, 1996).There are two broad categories of drying defects (some defects involve both causes):
* defects that arise due to the shrinkage anisotropy. This leads to warping: cupping, bowing, twisting, spring and diamonding.
* defects that arise due to uneven drying. This leads to the rupture of the wood tissue: checks (surface, end and internal), end splits, honey-combing and case-hardening. Another such defect is collapse, often seen as a corrugation, or "washboarding" of the wood surface (Innes, 1996). Collapse is a defect that results from the physical flattening of fibres, above the fibre saturation point (thus not a form of shrinkage anisotropy).

Australian and New Zealand Standard Organisations (AS/NZS 4787, 2001) have developed a standard for timber quality. Their five criteria for measuring drying quality:
# moisture content gradient and presence of residual drying stress (case-hardening);
# surface, internal and end checks;
# collapse;
# distortions;
# and discolouration caused by drying.This standard also indicates how to assess each of these drying quality criteria and provides a classification to express drying quality.

References

* ABARE (2000). National Plantation Inventory, March, 2000. 4p.
* Anon. (1997). Timber markets, home and away: Australian growers capitalising on international demand. Pie, Newsletter of Australia’s International and National Primary Industries and Energy (PIE) R&D Organisations. Volume 7 (Summer Issue): p14.
* Bootle, K.R. (1994). Wood in Australia: Types, Properties and Uses. McGraw-Hill Book Company, Sydney. 443p.
* Desch, H.E. and Dinwoodie, J.M. (1996). Timber: Structure, Properties, Conversion and Use. 7th ed. Macmillan Press Ltd., London. 306p.
* Doe, P.D., Oliver, A.R. and Booker, J.D. (1994). A Non-Linear Strain and Moisture Content Model of Variable Hardwood Drying Schedules. Proc. 4th IUFRO International Wood Drying Conference, Rotorua, New Zealand. 203-210pp.
* Haque, M.N. (1997). The Chemical Modification of Wood with Acetic Anhydride. MSc Dissertation. The University of Wales, Bangor, UK. 99p.
* Hoadley, R.Bruce. (2000). Understanding Wood:A Craftsman's Guide to Wood Technology. The Taunton Press. 280p. ISBN 1-56158-358-8
* Innes, T. (1996). Improving Seasoned Hardwood Timber Quality with Particular Reference to Collapse. PhD Thesis. University of Tasmania, Australia. 172p.
* Keey, R.B., Langrish, T.A.G. and Walker, J.C.F. (2000). Kiln-Drying of Lumber. Springer, Berlin. 326p.
* Kollmann, F.F.P. and Cote, W.A.J. (1968). Principles of Wood Science and Technology. I. Solid Wood. Springer-Verlag, NewYork. 592p.
* Kumar, S. (1994). Chemical modification of wood. Wood and Fiber Sci., 26(2):270-280.
* Langrish, T.A.G. and Walker, J.C.F. (1993). Transport Processes in Wood. In: Walker, J.C.F. Primary Wood Processing. Chapman and Hall, London. pp121-152.
* Panshin, A.J. and de Zeeuw, C. (1970). Textbook of Wood Technology. Volume 1, Third Edition. McGraw-Hill, New York, 705 p.
* Pordage, L.J. and Langrish, T.A.G. (1999). Simulation of the effect of air velocity in the drying of hardwood timber. Drying Technology - An International Journal, 17(1&2):237-256.
* Rowell, R.M. (1983). Chemical modification of wood. Forest Product Abstract, 6(12):363-382.
* Rowell, R.M. (1991). Chemical Modification of Wood. In: Hon, D.N.-S and Shiraishi, N. (eds), Wood and Cellulosic Chemistry. pp.703-756. Marcel Dekker, Inc., New York.
* Siau, J.F. (1984). Transport processes in wood. Springer-Verlag, NewYork. 245p.
* Sjostrom, E. (1993). Wood Chemistry: Fundamentals and Applications. Academic Press Limited, London. 293p.
* Skaar, C. (1988). Wood Water Relations. Springer-Verlag, NewYork. 283p.
* Stamm, A. J. (1964). Wood and Cellulose Science. Ronald Press, New York. 509p.
* Standard Australia (2000). Timber - Classification into Strength Groups. Australian/New Zealand Standard (AS/NZS) 2878. Sydney. 36p.
* Standard Australia (2001). Timber - Assessment of Drying Quality. Australian/New Zealand Standard (AS/NZS) 4787. Sydney. 24p.
* Strumillo, C. and Kudra, T. (1986). Drying: Principles, Applications and Design. Gordon and Breach Science Publishers, New York. 448p.
* Walker, J.C.F., Butterfield, B.G., Langrish, T.A.G., Harris, J.M. and Uprichard, J.M. (1993). Primary Wood Processing. Chapman and Hall, London. 595p.
* Wise, L.E. and Jahn, E.C. (1952). Wood Chemistry. Vol 2. Reinhold Publishing Corp., New York. 1343p.
* Wu, Q. (1989). An Investigation of Some Problems in Drying of Tasmanian Eucalypt Timbers. M.Eng. Sc. Thesis, University of Tasmania. 237p.

Related Journal

"Drying Technology [http://www.tandf.co.uk/journals/titles/07373937.asp] "

Further reading

* This Entry is edited extract from the Chapter 1 of [http://www.geocities.com/nhaque.geo/page3.html#PhD Ph.D. Thesis by Dr. Nawshadul Haque]

ee also

* Wood


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Wood — Wooden redirects here. For other uses, see Wooden (disambiguation). Heartwood redirects here. For other uses, see Heartwood (disambiguation). This article is about the substance. For small forests, see woodland. For wood as a commodity, see… …   Wikipedia

  • Wood — /wood/, n. 1. Grant, 1892 1942, U.S. painter. 2. Leonard, 1860 1927, U.S. military doctor and political administrator. * * * I Hard, fibrous material formed by the accumulation of secondary xylem produced by the vascular cambium. It is the… …   Universalium

  • Wood finishing — refers to the process of embellishing and/or protecting the surface. The process starts with surface preparation, either by sanding by hand (typically using a sanding block or power sander), scraping, or planing. Imperfections or nail holes on… …   Wikipedia

  • wood — wood1 woodless, adj. /wood/, n. 1. the hard, fibrous substance composing most of the stem and branches of a tree or shrub, and lying beneath the bark; the xylem. 2. the trunks or main stems of trees as suitable for architectural and other… …   Universalium

  • Drying — For the food conservation method, see drying (food). Drying is a mass transfer process consisting of the removal of water or another solvent [1] by evaporation from a solid, semi solid or liquid. This process is often used as a final production… …   Wikipedia

  • Drying oil — Plant oils linseed oil Types Vegetable fats (list) Macerated (list) Uses …   Wikipedia

  • Wood preservation — All measures that are taken to ensure a long life of wood fall under the definition wood preservation (timber treatment). Apart from structural wood preservation measures, there are a number of different (chemical) preservatives and processes… …   Wikipedia

  • Wood stain — A Wood stain, is a sub category of paint, consists of a pigment suspended in a vehicle of solvent and binding agent (alkyd, linseed oil, acrylic, polyurethane, lacquer, or resin). It is formulated to impart or transport the pigment into the pores …   Wikipedia

  • Wood-burning stove — For a list of stove types see Stove (disambiguation). A wood burning stove is a heating appliance capable of burning wood fuel and wood derived biomass fuel. Generally the appliance consists of a solid metal (usually cast iron or steel) closed… …   Wikipedia

  • drying — the removal of moisture from fish by evaporation as a means of preservation; see dried fish. May be natural, taking place in the open air or over wood fires, or technological involving vacuum or freeze drying, for example. Often used in… …   Dictionary of ichthyology

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”