Subaru EJ engine

Subaru EJ engine

The Subaru EJ engine is a series of automotive engines manufactured by Subaru, a division of Fuji Heavy Industries introduced mid 1989 for the 1st generation Legacy. The engine was designed by Masayuki Kodama, Takemasa Yamada and Shuji Sawafuji of FHI Ltd. Engines of this series are 16 valve flat-4 horizontal, with configurations available for SOHC and DOHC, natural aspiration and turbocharged. These engines are commonly used in light aircraft, kit cars and engine swaps into air cooled Volkswagens, but it's also popular as a swap into the wasserboxer engined Volkswagen Type 2.

Identifying An EJ

A 10-digit engine code is used by Subaru: the first 2 characters identify the engine series. The 3rd & 4th identify displacement volume in liters. The 5th digit is a sub-series identifier and fuel system flag. The 6th digit identifies emissions regulations it conforms to, while the 7th digit shows the intended transmission it was mated with. The final 3 digits are minor production change codes.


1.5 Litre SOHC

* Impreza (JDM only, though often seen in gray market exports to eastern Europe and Russia.)


1.6 Litre SOHC, convert|90|hp|abbr=on @ 5600 rpm.

* Impreza 93-94 (JDM only)
* Impreza 93-06 (Europe & Middle East)
* Impreza 93-97 (Australia)


1.8 Litre SOHC convert|110|hp|abbr=on @ 5600 rpm.

* Impreza 93-96
* Legacy (non-USDM) 90-96


2.0 Litre SOHC or DOHC


This is not actually a valid code from Subaru, but is mostly used by enthusiasts (and can be seen in such context on webforums such as rs25)& also mechanics to describe the entire line of 2.0 litre turbocharged engines that have been available over time. When referring to the EJ20T, one is speaking of one of the following:


EJ20G fall in to 2 categories-early engines 1989-9/1996-late wagon and automatic sedans from 1994/1996 and later

to identify an early EJ20G
*Coil on plug
*Divorced idle air wer qLate model EJ20Gs are the same general design as the EJ20K3a q3tUsage:
* Legacy RS 89-93
* Legacy RS-RA 89-93
* Legacy GT 89-93
* Impreza WRX 92~96
* Impreza WRX Wagon 92~98
* Impreza WRX STi 94~96


to identify an EJ20K
*Wasted spark coil pack on center of manifold
*Inlet under manifold
*Divorced idle air controller

*Impreza WRX & STi 9/96~9/98


This engine series is used for non-Japanese marketed WRX models in the world market as of 1999. The Japanese WRX models use the EJ207 from 1999~2001, except the 5-door wagon which also uses the EJ205. After 2001, all WRXs use the identify an EJ205:
*Coil on plug
*idle air integrated into throttle body

Impreza WRX

* 99~01 (JDM Wagon Body only)
* 01~current (all JDM)
* 02~05 (USDM)
* 99~current (all other markets)


to identify an 9/99-9/2000 EJ207
*Wasted spark coil pack off center of manifold
*Inlet under manifold
*Red manifold

* Impreza WRX STi 1998~present (JDM, specifically Homologation models for World_Rally_Championship)


This can refer to one of the 2.0 Litre DOHC Sequential Twin Turbo and intercooled engines (EJ20H/EJ20R/EJ206/EJ208). Yet like EJ20T, it is not actually a valid code used by Subaru themselves.

* Legacy GT, RS & B4 (JDM)



* Legacy BD/BG5 JDM GT's (183 kW manual & auto) and GTB's (190 kW auto)



* Legacy BD/BG5 JDM RSB and GTB's (205 kW Manual)


* Legacy BE/BH5 JDM GT's, GTB's and B4's (190 kW Auto)


* Legacy BE/BH5 JDM GT's, GTB's and B4's (205 kW Manual)


2.2 Litre SOHC

* Impreza 95-01
* Legacy 90-99

EJ22 Enhancements and Improvements

2.2 Liter Engine EnhancementsBeginning in the 1997 Model Year, the 2.2 liter engine for 1997 Legacy and Impreza models has had internal and external changes that yield an approximately 10% increase in power and 3% increase in fuel economy.

Accomplishing this involves many factors, one of which is engine friction reduction. The piston, a major source of engine friction, has been coated with a friction reducing agent called Molybdenum. This thin coating not only allows smoother travel through the cylinder, but also reduces cylinder wall scuffing.

The skirt of the piston has been reshaped and the overall weight has been reduced by approximately 100 grams. Compression ratio has been increased to 9.7 to 1 by reshaping the crown of the piston. This eliminates the clearance that was available between the piston at TDC and the fully opened valve.

Piston pin offset has been changed to 0.5 mm. Piston to cylinder wall clearance has been reduced by increasing the piston diameter.

Another source of high engine friction is the valve train. Hydraulic lash adjusters (HLAs) are always in contact with the valves. The hydraulic pressure of the lash adjuster must be overcome during operation and during the most critical time of engine start.

To overcome this situation and to contribute to the total reduction of friction loss, 1997 and later SOHC engines have solid valve adjusters. The scheduled service of this valve train is set at 100,000 miles. SOHC engines now use an adjustment screw to adjust valve clearance.

The roller rocker cam follower system that was introduced on the 1.8L Impreza engines, is installed on all 1995 model year and later 2.2 liter engines. The roller assemblies are not serviceable separately, but the rocker arms may be serviced as individual units.

The carbon composition head gaskets with integrated o-rings are interchangeable from left to right on 1990 to 1994 N/A engines only.

Other Engine Modifications (2.2L 1997) The intake manifold has been reshaped to increase the airflow mass and speed, contributing to improved low and mid engine speed operation. Components located on the intake manifold have been relocated as compared to the 1996 models. EGR Solenoid, Purge Control Solenoid, etc.

1999 2.2 Liter Phase 2 Engine Enhancements (from endwrench article H-4 and H-6 service):All 2.2 liter engine for 1999 are the Phase 2 design. The 2.2 liter Phase 2 engines are a SOHC design, with a newly-designed cylinder head. Changes in the 2.2 liter Phase 2 engines are as follows:

* The engine and transmission are fastened with six bolts and two studs.
* The thrust bearing has been moved to the number 5 position.
* The oil groove in the number 1 and 3 have been changed to supply additional lubrication to the crank journal.

Additional Phase 2 Engine Features
* The cylinder head is a two-rocker shaft, solid type valve system with roller followers.
* The valves are positioned at a larger angle than previous model years. The intake valves are positioned 23 degrees off-center with the exhaust valvespositioned 20 degrees off-center. Prior model year engines utilized a 15-degree positioning angle.
* Head gasket thickness is 0.7 mm.
* The intake rocker arms are marked so they are correctly placed on the rocker shaft when servicing. An IN1 or IN2 will be embossed on each rocker arm. As viewed from the front of the engine the Number 1 intake valve of ach cylinder and the number 2 intake valve have an IN1 marked and IN2 arked rocker arm that mates with it. New IN1 rocker arms can also be identified by a Green painted mark on the top of the rocker arm. The IN2 rocker arms have a white mark. Proper positioning is maintained through the use of a wave washer located between the rocker shaft arm and rocker arm shaft support.
* The camshaft is secured to the cylinder head with the camcase. An oil passage in the cylinder head provides the passageway in the camcase with oilthat leads to the intake rocker shaft. Oil from the camshaft is collected on the opposite side of the passageway leading to the intake rocker shaft to provide oil to the exhaust rocker shaft.

Note: Cylinder head and camcase must be replaced together (line bored).
* The sparkplug pipe is pressed into the cylinder head and is not serviceable.If it becomes damaged the cylinder head must be replaced. The sealsinstalled onto the ends of the sparkplug pipes seal against the valve covers and should be replaced when the valve cover is removed.
* Pistons on the 2.2 liter engines have a 0.5 mm offset with the engine having a compression ratio of 10.0 to 1. The horsepower has increased to 142 hp @ 5600 RPM. Maximum torque is149 ft·lbf @ 3600 RPM.
* Camshaft sprockets are constructed of a resin type material with a metal key pressed into the sprocket for maintaining proper sprocket to shaft orientation.


2.2 litre

convert|135|bhp|abbr=on @ 5800 rpmconvert|140|ft.lbf|N.m|abbr=on @ 4800 rpm

Australian model - convert|100|kW|hp|abbr=on @ 6000 rpmconvert|189|Nm|ftlbf|abbr=on @ 4800 rpm

* Legacy 89-99
* Impreza 93-01


2.2 Litre SOHC Turbo, fully closed deck, oil squirters, no intercooler

* Legacy 89-94 (North American market only from 1991)


turbocharged 2.2 litre DOHC with 2.5 litre heads.Usage:
* Impreza WRX STi 22B (JDM)


2.5 Litre


The EJ251 is a 2.5 L (2457 cc) Horizontally Opposed SOHC Engine with a bore of convert|99.5|mm|in|abbr=on and a stroke of convert|79.0|mm|in|abbr=on. Compression ratio is 10.0: 1. Firing order is 1 - 3 - 2 - 4. SAE power:

* Impreza RS 99-05 (US)
* Impreza Outback 00-04 (US)
* Forester 99-04
* Outback 00-04 (US)



* Legacy 00


SOHC - convert|175|hp|abbr=on @ 5600 rpm, convert|166|ftlbf|Nm|abbr=on torque @ 4000 rpm. I-Active valves(VVT intake side.)
* Impreza 06+
* Legacy 05+
* Forester 05+
* Baja 05+


DOHC - 165hp @ 5600 rpm convert|162|ftlbf|Nm|abbr=on at 4000 rpm

* Impreza 98
* Legacy 96~99
* Forester 98~99


SOHC 16 valve

* Impreza RS 99~01
* Forester 99~00
* Legacy 00~01


2.5 litre DOHC AVCS turbocharged, with sodium-filled valves originally designed for North American market, now sees usage in some European Imprezas and Legacies destined for Australia and South Africa.

Usage in North America:
* Impreza: 2006 - present
* Forester: 2004 - present
* Legacy: 2005 - present
* Baja: 2004 - 2006

Usage in the rest of the world:
* Legacy: 2005 - present
* Impreza: 2006 - present


DOHC 16 valve turbo

* US Market Impreza WRX STi MY04~present (300 hp)

* Asian, European Market Impreza WRX STi 05~present (280 hp, 40KGh/m)

Subaru Formula One Flat-12

An unexpected contract with Subaru, the automobile branch of Fuji Heavy Industries, brought substantial monetary backing and additionally an exclusive "works" engine for free. The Japanese took over 51% of Coloni formula, paid the debts and supported the new alliance with a brand new, unique engine. It was a flat-12 engine which in fact was penned by Carlo Chiti. Chiti's Motori Moderni company at Novara had supplied V6 Turbo engines for the Minardi Formula One team from 1985 to 1987, and in 1988 Chiti had penned a normally aspirated V12 engine that attracted Subaru. In late 1988, the Japanese commissioned Chiti to design a new Formula One engine with a "flat" layout - as used in their road cars - that was ready in the Summer of 1989. The engine - now with a Subaru badge - was tested in a Minardi M188 chassis but due to a severe lack of power Minardi very soon lost interest. After a few months of searching, Subaru found the Coloni team. Eventually, the "Subaru Coloni" Team was founded with Enzo Coloni staying on board as the man for operational business.

By the beginning of 1990, the "Subaru" flat engine was not producing more than 500 bhp, so the Coloni Subaru was by far the least competitive machine regularly competing in Formula One in 1990. Subaru and Chiti agreed to build a new V12 engine for Summer 1990 together with a completely new chassis, but in the meantime the flat engine should be used by the "Coloni Subaru" Team in a carry-over chassis. Early in 1990, a handful of Enzo Coloni's mechanics worked on a single C3 and tried to put the Subaru engine in it. The work was not done until the day the FIA started shipping the Formula One material to Phoenix. In the pits at Phoenix, the car was assembled for the very first time, and a short private "practice" took place on a parking area of an American supermarket. On prequalification day of Phoenix the world saw Coloni's "new" model C3B which wore a white, red and green livery. Without an airbox but with wide, long sidepods, it looked like a tank, was overweight by 300 pounds and nearly impossible to handle. Neither at Phoenix nor at any other event, did Bertrand Gachot, Coloni's new driver, manage to prequalify the car. As the season went on, improvements were few and results stayed nowhere. Meanwhile, no success could be seen at Coloni's plant in Perugia where obviously nobody worked seriously on a new car. In May, Enzo Coloni was sacked by Subaru, but no improvement came. In June, the Japanese company withdrew completely and sold the team back to Enzo Coloni, debt free, but with no sponsors and no engines. By the German Grand Prix Coloni had arranged a supply of Cosworth engines, prepared by Langford & Peck. An improved car also appeared in Germany. The "new" Coloni C3C was simply a 1989 C3 with minor changes in aerodynamics. The car was quicker, but not enough to achieve any serious results. Gachot was usually able to prequalify his car, but the "main" qualification was still out of reach. By the end of the season, Coloni had not taken part in a single Grand Prix.

Other Data

All the EJ series share compatibility and construction similarity and are 16 valved engines. The EJ series started with the EJ15, a 1.5 liter (SOHC) and makes ~90 hp, then the EJ16, a 1.6 litre single overhead cam (SOHC). Later followed by the EJ20, a 120 hp 2.0 litre single overhead cam and the EJ22, a 135 hp 2.2 litre single overhead cam. The EJ20 turbocharged version was developed with dual overhead cams, as well as non-turbo DOHC engines and DOHC twin-turbos. The EJ18 and EJ20 were most popular in Europe and the EJ22T SOHC, mostly in the US and is known as the bulletproof Subaru engine.

The SOHC EJ Subaru boxer engines were non-interference engines through 1996, run by a single timing belt driving both cams (both sides of the engine) and the water pump. Because they are non-interference engines, if the timing belt fails, the engine of the models up to 1996 will not be destroyed. The oil pump is driven directly from the crank shaft and the waterpump by the timing belt. All DOHC and 1997-up SOHC EJ engines are interference engines, if the timing belt fails the engine will likely be destroyed or the valves & piston will be heavily damaged.


Subaru 2.5-liter Turbo Boxer Engine won 'best engine' in the 2.0-2.5 litre category in the 2006 International Engine of the Year awards.


* [ Subaru Engine Specs and Designations]

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Subaru EA engine — Infobox Automobile engine name = Subaru EA 81 aka = manufacturer = Fuji Heavy Industries type = Flat 4 bore = 3.622 in (92 mm) stroke = 2.638 in (67 mm) displacement = 108.7 in³ (1781 cm³) length = diameter = width = height = weight = 171 lb (78… …   Wikipedia

  • Subaru EF engine — The EF is an automotive engine made by Subaru, introduced in 1984 for the Subaru Justy.It is a water cooled straight 3 engine with a belt driven single overhead camshaft, and a chain driven balance shaft. It has an alloy cylinder head and iron… …   Wikipedia

  • Subaru Legacy — Subaru Legacy …   Википедия

  • Subaru B4 — Subaru Legacy (русск. Субару Легаси)  седан или универсал повышенной проходимости (кроссовер, японской фирмы 1989 года, на международный рынок поставляется с 1990 года. В Австралии Legacy имеет название Liberty из уважения к Legacy Австралия,… …   Википедия

  • Subaru Legacy B4 — Subaru Legacy (русск. Субару Легаси)  седан или универсал повышенной проходимости (кроссовер, японской фирмы 1989 года, на международный рынок поставляется с 1990 года. В Австралии Legacy имеет название Liberty из уважения к Legacy Австралия,… …   Википедия

  • Subaru Liberty — Subaru Legacy (русск. Субару Легаси)  седан или универсал повышенной проходимости (кроссовер, японской фирмы 1989 года, на международный рынок поставляется с 1990 года. В Австралии Legacy имеет название Liberty из уважения к Legacy Австралия,… …   Википедия

  • Subaru Legacy Touring Wagon — Subaru Legacy (русск. Субару Легаси)  седан или универсал повышенной проходимости (кроссовер, японской фирмы 1989 года, на международный рынок поставляется с 1990 года. В Австралии Legacy имеет название Liberty из уважения к Legacy Австралия,… …   Википедия

  • Subaru Impreza WRX — Infobox Automobile boxcolor = darkgreen name = Subaru Impreza WRX manufacturer = Subaru parent company = Fuji Heavy Industries production = 1992 ndash;present class = Sport compact assembly = Ōta, Gunma, Japan layout = Front engine, symmetrical… …   Wikipedia

  • Subaru — Infobox Company company name = Subaru company company type = Division of Fuji Heavy Industries slogan = flagicon|Japan flagicon|Canada flagicon|Europe Think. Feel. Drive. flagicon|Australia Advanced Driving Technologyflagicon|United Kingdom… …   Wikipedia

  • Subaru Alcyone SVX — Infobox Automobile name=Subaru Alcyone SVX aka=Subaru SVX / Alcyone SVX manufacturer=Subaru parent company=Fuji Heavy Industries (FHI) class=Sport compact similar=Toyota Supra Mitsubishi 3000GT Nissan 300ZX production=1991 1997 predecessor=Subaru …   Wikipedia