- Thermal management of electronic devices and systems
Heatgenerated by electronic devices and circuitry must be dissipated to improve reliabilityand prevent premature failure. Techniques for heat dissipation can include heatsinks and fans for air cooling, and other forms of computer coolingsuch as liquid cooling.
In cases of extreme low environmental temperatures, it may actually be necessary to heat the electronic components to achieve satisfactory operation.
Thermal resistance of devices
This is usually quoted as the thermal resistance from
junctionto case of the semiconductordevice. The units are °C/W. For example, a heatsink rated at 10 °C/W will get 10°C hotter than the surrounding air when it dissipates 1 Watt of heat. Thus, a heatsink with a low °C/W value is more efficient than a heatsink with a high °C/W value.
Thermal time constants
A heatsink's thermal mass can be considered as a capacitor (storing heat instead of charge) and the thermal resistance as an electrical resistance (giving a measure of how fast stored heat can be dissipated). Together, these two components form a thermal
RC circuitwith an associated time constant given by the product of R and C. This quantity can be used to calculate the dynamic heat dissipation capability of a device, in an analogous way to the electrical case.A specific type of thermalinterface material is put between the heat sink and the heat source to increase thermal throughput), such as a microprocessorchip or other power handling semiconductorto stablise its temperaturethrough increased thermal massand heat dissipation (primarily by conduction and convection and to a lesser extent by radiation).
Heat sinks are widely used in
electronics, and have become almost essential to modern central processing units. In common use, it is a metalobject brought into contact with an electronic component's hot surface — though in most cases, a thin thermal interface materialmediates between the two surfaces. Microprocessors and power handling semiconductors are examples of electronics that need a heat sink to reduce their temperature through increased thermal massand heat dissipation (primarily by conduction and convectionand to a lesser extent by radiation). Heat sinks have become almost essential to modern integrated circuitslike microprocessors, DSPs, GPUs, and more.
A heat sink usually consists of a metal structure with one or more flat surfaces to ensure good thermal contact with the components to be cooled, and an array of comb or fin like protrusions to increase the surface contact with the air, and thus the rate of heat dissipation.
A heat sink is sometimes used in conjunction with a fan to increase the rate of airflow over the heat sink. This maintains a larger temperature gradient by replacing warmed air faster than convection would. This is known as a forced air system.
A heat sink (or heatsink) is an environment or object that absorbs and dissipates heat from another object using
thermal contact(either direct or radiant). Heat sinks are used in a wide range of applications wherever efficient heat dissipation is required; major examples include refrigeration, heat enginesand cooling electronic devices.
Heat sinks function by efficiently transferring
thermal energy("heat") from an object at high temperature to a second object at a lower temperature with a much greater heat capacity. This rapid transfer of thermal energy quickly brings the first object into thermal equilibriumwith the second, lowering the temperature of the first object, fulfilling the heat sink's role as a cooling device. Efficient function of a heat sink relies on rapid transfer of thermal energy from the first object to the heat sink, and the heat sink to the second object.
The most common design of a heat sink is a metal device with many fins. The high
thermal conductivityof the metal combined with its large surface area result in the rapid transfer of thermal energy to the surrounding, cooler, air. This cools the heat sink and whatever it is in direct thermal contact with. Use of fluids (for example coolants in refrigeration) and thermal interface material(in cooling electronic devices) ensures good transfer of thermal energy to the heat sink. Similarly, a fan may improve the transfer of thermal energy from the heat sink to the air.
Construction and materials
A heat sink usually consists of a base with one or more flat surfaces and an array of comb or fin-like protrusions to increase the heat sink's surface area contacting the air, and thus increasing the heat dissipation rate. While a heat sink is a static object, a fan often aids a heat sink by providing increased airflow over the heat sink — thus maintaining a larger temperature
gradientby replacing the warmed air more quickly than passive convection achieves alone — this is known as a forced air system.
Heat sinks are made from a good thermal conductor such as
copperor aluminumalloy. Copper (401 W/(m·K) at 300 K) is significantly more expensive than aluminum (237 W/(m·K) at 300 K) but is also roughly twice as efficient as a thermal conductor. Aluminum has the significant advantage that it can be easily formed by extrusion, thus making complex cross-sections possible. Aluminum is also much lighter than copper, offering less mechanical stress on delicate electronic components. Some heat sinks made from aluminum have a copper core as a trade off. The heat sink's contact surface (the base) must be flat and smooth to ensure the best thermal contact with the object needing cooling. Frequently a thermally conductive grease is used to ensure optimal thermal contact, such compounds often contain colloidal silver. Further, a clamping mechanism, screws, or thermal adhesive hold the heat sink tightly onto the component, but specifically without pressure that would crush the component.
Heat sink performance (including free convection, forced convection, liquid cooled, and any combination thereof) is a function of material, geometry, and overall surface heat transfer coefficient. Generally, forced convection heat sink thermal performance is improved by increasing the thermal conductivity of the heat sink materials, increasing the surface area (usually by adding extended surfaces, such as fins or foam metal) and by increasing the overall area heat transfer coefficient (usually by increase fluid velocity, such as adding fans, pumps, etc.).
Online heat sink calculators from companies such as Novel Concepts, Inc., can accurately estimate forced convection heat sink performance. For more complex heat sink geometries, and/or heat sinks with multiple materials, and/or heat sinks with multiple fluids, computation fluid dynamics (CFD) analysis is recommended (see graphics on this page).
Use in electronics
Due to recent technological developments and public interest, the retail heat sink market has reached an all time high. In the early 2000s,
CPUs were produced that emitted more and more heat than earlier, escalating requirements for quality cooling systems. Overclockinghas always meant greater cooling needs, and the inherently hotter chips meant more concerns for the enthusiast. Efficient heat sinks are vital to overclocked computer systems because the higher a microprocessor's cooling rate, the faster the computer can operate without instability; generally, faster operation leads to higher performance. Many companies now compete to offer the best heat sink for PC overclocking enthusiasts. Prominent aftermarket heat sink manufacturers include: Advanced Thermal Solutions, Inc., www.qats.com, Aero Cool, Cooler Master, Foxconn, Thermalright, Thermaltake, Swiftech, and Zalman.
Temporary heat sinks were sometimes used while
solderingcircuit boards, preventing excessive heat from damaging sensitive nearby electronics. In the simplest case, this means partially gripping a component using a heavy metal crocodile clipor similar clamp. Modern semiconductor devices, which are designed to be assembled by reflow soldering, can usually tolerate soldering temperatures without damage. On the other hand, electrical components such as magnetic reed switches can malfunction if exposed to higher powered soldering irons, so this practice is still very much in use. [http://www.eleinmec.com/article.asp?23]
synthetic diamondcooling sinks are being researched to provide better cooling. Also, some heat sinks are constructed of multiple materials with desirable characteristics, such as phase change materials, which can store a great deal of energy due to their heat of fusion.
Convective air cooling
This term describes device cooling by the convection currents of the warm air being allowed to escape the confines of the component to be replaced by cooler air. Since warm air normally rises, this method usually requires venting at the top or sides of the casing to be effective.
Forced air cooling
If there is more air being forced into a system than being pumped out (due to an imbalance in the number of fans), this is referred to as a 'positive' airflow, as the pressure inside the unit is higher than outside.
A balanced or neutral airflow is the most efficient, although a slightly positive airflow results in less dust build up.
A heat pipe is a heat transfer mechanism that can transport large quantities of heat with a very small difference in
temperaturebetween the hot and cold interfaces. A typical heat pipe consists of sealed hollow tube made of a thermoconductive metal such as copperor aluminium. The pipe contains a relatively small quantity of a "working fluid" or coolant(such as water, ethanolor mercury) with the remainder of the pipe being filled with the vapour phase of the working fluid, all other gases being excluded.The advantage of heat pipes is their great efficiency in transferring heat. They are actually more "conductive" than a copper bar of equivalent cross-section.
Peltier cooling plates
Peltier cooling plates uses the Peltier effect to create a heat flux between the junction of two different types of materials. This effect is commonly used for cooling electronic components and small instruments.
There are no moving parts and such a device is maintenance free. Due to the relatively low efficiency, thermoelectric cooling is generally only used in environments where the solid state nature outweighs the poor efficiency. Thermoelectric junctions are generally only around 10% as efficient as the ideal refrigerator (Carnot cycle), compared with 40% achieved by conventional compression cycle systems.
Synthetic Jet Air Cooling
Synthetic Jetis produced by a continual flow of vortices that are formed by alternating brief ejection and suction of air across an opening such that the net mass flux is zero. A unique feature of these jets is that they are formed entirely from the working fluid of the flow system in which they are deployed can produce a net momentum to the flow of a system without net mass injection to the system.
Synthetic jet air movers have no moving parts and are thus maintenance free. Due to the high heat transfer coefficients, high reliability but lower overall flow rates, Synthetic jet air movers are usually used at the chip level and not at the system level for cooling. However depending on the size and complexity of the systems they can be used for both at times.
Thermal resistance in electronics
* [http://www.sems.com.my/ SEMS Sdn Bhd: Heat Sink, Automation & Robots, Metal Stamping]
* [http://www.novelconceptsinc.com/ Online Heat Sink Calculators]
* [http://www.frostytech.com/articlesearch.cfm?SearchValue=&Search=Search&Category=198&CategorySearch=Get+Listing Over 350 reviews of CPU heatsinks with synthetic thermal test apparatus] (
* [http://www.madshrimps.be/gotoartik.php?articID=389 Hundreds of CPU heatsink tests in real world conditions] (
* [http://www.heatsink-guide.com/heatsinkinfo-2.shtml Overview of different manufacturing methods to produce a heat sink]
* [http://www.tomshardware.com/2001/09/17/hot_spot/index.html Tom's hardware test: What happens when the processor heat sink is removed]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Thermal management of high power LED — With the coming of energy saving era, high power light emitting diodes (LEDs) are promising to replace other technologies such as incandescent and fluorescent bulbs in signaling, solid state lighting, and vehicle headlight applications due to… … Wikipedia
Electronic waste — For the EC directive, see Waste Electrical and Electronic Equipment Directive. Defective and obsolete electronic equipment. Electronic waste, e waste, e scrap, or Waste Electrical and Electronic Equipment (WEEE) describes discarded electrical or… … Wikipedia
Thermal copper pillar bump — The Thermal Copper Pillar Bump, also known as the thermal bump , is a thermoelectric device made from thin film thermoelectric material embedded in flip chip interconnects (in particular copper pillar solder bumps) for use in electronics and… … Wikipedia
Saint Petersburg State University of Information Technologies, Mechanics and Optics — Infobox University name = Saint Petersburg State University of Information Technologies, Mechanics and Optics native name = Санкт Петербургский государственный университет информационных технологий, механики и оптики latin name = motto =… … Wikipedia
Mathematics and Physical Sciences — ▪ 2003 Introduction Mathematics Mathematics in 2002 was marked by two discoveries in number theory. The first may have practical implications; the second satisfied a 150 year old curiosity. Computer scientist Manindra Agrawal of the… … Universalium
Copper wire and cable — Copper has been used in electric wiring since the invention of the electromagnet and the telegraph in the 1820s. The invention of the telephone in 1876 proved to be another early boon for copper wire. Today, despite competition from… … Wikipedia
Mobile phone radiation and health — A man speaking on a mobile telephone The effect of mobile phone radiation on human health is the subject of recent interest and study, as a result of the enormous increase in mobile phone usage throughout the world (as of June 2009 … Wikipedia
Nuclear and radiation accidents — This article is about nuclear and radiation accidents in general. For a list of military nuclear accidents, see List of military nuclear accidents. For a list of civilian nuclear accidents, see List of civilian nuclear accidents. For a discussion … Wikipedia
Business and Industry Review — ▪ 1999 Introduction Overview Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… … Universalium
Defence Research and Development Organisation — Sanskrit: बलस्य मूलं विज्ञानम् Strength s Origin is in Science  Agency overvi … Wikipedia