- Audio system measurements
Audio system measurements are made for several purposes. Designers take measurements so that they can specify the performance of a piece of equipment. Maintenance engineers make them to ensure equipment is still working to specification, or to ensure that the cumulative defects of an audio path are within limits considered acceptable. Some aspects of measurement and specification relate only to intended usage. For example,
magnetic tapespeeds and types, interface specifications, or power output.
Others are intended as an index of the quality, or 'fidelity', of reproduction perceivable by a human. It is important that such measurements accommodate
psychoacousticprinciples, so that they truly measure the system in a way that is 'subjectively valid'.
Subjectivity and frequency weighting
Measurements based on psychoacoustics, such as the measurement of noise, often use a
weighting filter. It is well-established that human hearingis more sensitive to some frequencies than others, as demonstrated by equal-loudness contours, but it is not well appreciated that these contours vary depending on the type of sound. The measured curves for pure tones, for instance, are different from those for random noise. The ear also responds less to short bursts, below 100 to 200 ms, than to continuous sounds [ Moore, Brian C. J., "An Introduction to the Psychology of Hearing", 2004, 5th ed. p137, Elsevier Press] such that a quasi-peakdetector has been found to give the most representative results when noise contains click or bursts, as is often the case for noise in digital systems. [ BBC Research Report EL17, "The Assessment of Noise in Audio Frequency Circuits", 1968.] For these reasons a set of subjectively valid measurement techniques have been devised and incorporated into BS, IEC, EBU and ITUstandards. These newer methods of audio quality measurementare used by broadcast engineers throughout most of the world, as well as by some audio professionals, though the older A-weightingstandard for continuous tones is still commonly used by others. [http://www.sweetwater.com/expert-center/glossary/t--ANSIA-Weighting] Subjectively valid methods came to prominence in consumer audio in the UK and Europe in the 1970s, when the introduction of compact cassettetape and DBXand Dolby noise reductiontechniques revealed the unsatisfactory nature of many basic engineering measurements. The specification of weighted CCIR-468 quasi-peak noise, and weighted quasi-peak wow and flutter became particularly widely used and attempts were made to find more valid methods for distortion measurement.
No single measurement can assess audio quality. Instead, it is usual to take a series of measurements to test for the various types of degradation that can reduce fidelity. Thus, when testing an analogue tape machine it is necessary to test for
wow and flutterand tape speed variations over longer periods, as well as for distortion and noise. When testing a digital system, testing for speed variations is normally considered unnecessary given the nearly ubiquitous accurate clocks in digital circuitry, but testing for aliasingand timing jitteris often desirable, as these have caused audible degradation in many systems. The claim is often made that different methods of measuring noise, or distortion, are better suited to different items of equipment is not widely believed among professional audio engineers.
Once subjectively valid methods have been shown to correlate well with listening tests over a wide range of conditions, then such methods are generally adopted as preferred. But it's important to realise that engineering methods are not always sufficient to when comparing like with like. One CD player, for example, might have higher measured noise than another CD player when measured RMS, or even A-weighted RMS, yet sound quieter and measure lower when 468-weighting is used. This could be because it has more noise at high frequencies, or even at frequencies beyond 20 kHz, both of which are less important since human ears are less sensitive to them. See
noise shaping.) This effect is how Dolby B works and why it was introduced. Cassette noise, which was predominately high frequency and unavoidable given the small size and speed of the recorded track could be made subjectively much less important. The noise sounded 10 dB quieter, but failed to measure much better unless 468-weighting was used rather than A-weighting.
Frequency response: The signal should be passed at least over the audible range (usually quoted as 20 Hz to 20 kHz) with no significant peaks or dips. The human ear can discern differences in level of about 3 dB in some frequency ranges, so peaks and troughs must be less than this. Much modern equipment is capable of less than ±1 dB variation over the entire audible frequency range. Rapid variations over a small frequency range (ripple), or very steep rolloffs are considered undesirable as they can correspond to resonances associated with energy storage which produce delayed echoes and hence colouration, or decreased quality, of the sound.
Total harmonic distortion(THD) : In music material, there are distinct tones, and some kinds of distortion involve spurious double or triple the frequencies of those tones. Such harmonically related distortion is called harmonic distortion. For high fidelity, this is usually expected to be < 1% for electronic devices; mechanical elements such as loudspeakers usually have inescapable higher levels. Low distortion is relatively easy to achieve in electronics with use of negative feedback, but the use of high levels of feedback in this manner has been the topic of much controversy among audiophiles — see electronic amplifier. Essentially all loudspeakers produce more distortion than electronics, and 1–5% distortion is not unheard of at moderately loud listening levels. Human ears are less sensitive to distortion in the bass frequencies, and levels are usually expected to be under 10% at loud playback. Distortion which creates only even-order harmonics for a sine wave input is sometimes considered less bothersome than odd-order distortion.
; Output power : Output power for amplifiers is ideally measured and quoted as maximum Root Mean Square (RMS) power output per channel, at a specified distortion level at a particular load, which by convention and government regulation, is considered the most meaningful measure of power available on music signals, though real, non-
clippingmusic has a high peak-to-average ratio, and usually averages well below the maximum possible. The commonly given measurement of PMPO (peak music power out) is largely meaningless and often used in marketing literature; in the late 1960s there was much controversy over this point and the US Government (FTA) required that RMS figures be quoted for all high fidelity equipment. Music power has been making a comeback in recent years. "See also Audio power.": Power specifications require the load impedanceto be specified, and in some cases two figures will be given (for instance, a power amplifier for loudspeakers will be typically measured at 4 and 8 ohms). Any amplifier will drive more current to a lower impedance load. For example, it will deliver more power into a 4-ohm load, as compared to 8-ohm, but it must not be assumed that it is capable of sustaining the extra current unless it is specified so. Power supply limitations may limit high current performance.
Intermodulation distortion(IMD) : Distortion which is not harmonically related to the signal being amplified is intermodulation distortion. It is a measure of the level of spurious signals resulting from unwanted combination of different frequency input signals. This effect results from non-linearities in the system. Sufficiently high levels of negative feedback can reduce this effect in an amplifier. Many believe it is better to design electronics in a way to minimize feedback levels, though this is difficult to achieve while meeting other high accuracy requirements. Intermodulation in loudspeaker drivers is, as with harmonic distortion, almost always larger than in most electronics. IMD increases with cone excursion. Reducing a driver's bandwidth directly reduces IMD. This is achieved by splitting the desired frequency range into separate bands and employing separate drivers for each band of frequencies, and feeding them through a crossover filter network. Steep slope crossover filters are most effective at IMD reduction, but may be too expensive to implement using high-current components and may introduce ringing distortion. [ [http://www.xsgeo.com/course/filt.htm Excess Geophysics. "FREQUENCY FILTERING in practice"] ]
; Noise : The level of unwanted noise generated by the system itself, or by interference from external sources added to the signal.
Humusually refers to noise only at power line frequencies (as opposed to broadband white noise), which is introduced through induction of power line signals into the inputs of gain stages. Or from inadequately regulated power supplies.
Crosstalk: The introduction of noise (from another signal channel) caused by stray inductance or capacitance between components or lines. Crosstalk reduces, sometimes noticeably, separation between channels (eg, in a stereo system). It is given in dB relative to a nominal level of signal in the path receiving interference. Crosstalk is normally only a problem in equipment in which several audio channels are handled in the same chassis.
Common-mode rejection ratio(CMRR) : All electronic equipment with inputs is susceptible to this problem. In balanced audiosystems, there are equal and opposite signals (difference-mode) in inputs, and any interference imposed on both leads will be subtracted, canceling out that interference (ie, the common-mode). CMRR is a measure of a system's ability to ignore any such interference and especially humwhich arises at its input. It is generally only significant with long lines on an input, or when some kinds of ground loopproblems exist. Unbalanced inputs do not have common mode resistance; induced noise on their inputs appears directly as noise or hum.
Dynamic range"and" Signal-to-noise ratio(SNR) : The difference between the maximum level a component can accommodate and the noise level it produces. Input noise is not counted in this measurement. It is measured in dB. : "Dynamic range" refers to the ratio of maximum to minimum loudness in a given signal source (eg, music or programme material), and this measurement also quantifies the maximum dynamic range an audio system can carry. This is the ratio (usually expressed in dB) between the noise floor of the device with no signal and the maximum signal (usually a sine wave) that can be output at a specified (low) distortion level. :Since the early 1990s it has been recommended by several authorities including the Audio Engineering Societythat measurements of dynamic range be made with an audio signal present. This avoids questionable measurements based on the use of blank media, or muting circuits.
: "Signal-to-noise ratio" (SNR), however, is the ratio between the noise floor and an arbitrary reference level or
alignment level. In "professional" recording equipment, this reference level is usually +4 dBu (IEC 60268-17), though sometimes 0 dBu (UK and Europe - EBU standard Alignment level). 'Test level', 'measurement level' and 'line-up level' mean different things, often leading to confusion. In "consumer" equipment, no standard exists, though −10 dBV and −6 dBu are common. : Different media characteristically exhibit different amounts of noise and headroom. Though the values vary widely between units, a typical analogue cassette might give 60 dB, a CD almost 100 dB. Most modern quality amplifiers have >110 dB dynamic range, which approaches that of the human ear, usually taken as around 130 dB. See Programme levels.
Phase distortion", " Group delay", and " Phase delay: A perfect audio component will maintain the phase coherency of a signal over the full range of frequencies. Phase distortion can be extremely difficult to reduce or eliminate. The human ear is largely insensitive to phase distortion, though it is exquisitely sensitive to relative phase relationships within heard sounds. The complex nature of our sensitivity to phase errors, coupled with the lack of a convenient test that delivers an easily understood quality rating, is the reason that it is not a part of conventional audio specifications.Fact|date=October 2008 Multi-driver loudspeaker systems may have complex phase distortions, caused or corrected by crossovers, driver placement, and the phase behaviour of the specific driver.
Transient response: A system may have low distortion for a steady-state signal, but not on sudden transients. In amplifiers, this problem can be traced to power supplies in some instances, to insufficient high frequency performance or to excessive negative feedback. Related measurements are slew rateand rise time. Distortion in transient response can be hard to measure. Many otherwise good power amplifier designs have been found to have inadequate slew rates, by modern standards. In loudspeakers, transient response performance is affected by the mass and resonances of drivers and enclosures and by group delay and phase delayintroduced by poorly-designed crossover filtering or inadequate time alignment of all the loudspeaker's drivers. Most loudspeakers generate significant amounts of transient distortion, though some designs are less prone to this (e.g. electrostatic loudspeakers, plasma arc tweeters, ribbon tweeters and horn enclosures with multiple entry points).
Damping factor: A higher number is generally believed to be better. This is a measure of how well a power amplifiercontrols the undesired motion of a loudspeakerdriver. An amplifier must be able to suppress resonances caused by mechanical motion (e.g., inertia) of a speaker cone, especially a low frequency driver with greater mass. For conventional loudspeaker drivers, this essentially involves ensuring that the output impedanceof the amplifier is close to zero and that the speaker wires are sufficiently short and have sufficiently large diameter. Damping factor is the ratio of the output impedance of an amplifier and connecting cables to the DC resistance of a voice coil, which means that long, skinny speaker wires will undo the benefits of good electronic damping performance from the amplifier. A damping factor of 20 or greater is considered adequate for live sound reinforcement systems, as the SPL of inertia-related driver movement is 26 dB less than signal level and won't be heard. [ [http://www.prosoundweb.com/ee/images/uploads/df.pdf ProSoundWeb. Chuck McGregor, Community Professional Loudspeakers. September 1999. "What is Loudspeaker Damping and Damping Factor (DF)?"] ] Negative feedback in an amplifier design generally increases its damping factor. [ [http://www.aikenamps.com/NegativeFeedback.htm Aiken Amplification. Randall Aiken. "What is Negative Feedback?" 1999] ]
; Wow and
flutter: These measurements are related to physical motion in a component, largely the drive mechanism of analogue media, such as vinyl records and magnetic tape. "Wow" is slow speed (a few Hz) variation, caused by longer term drift of the drive motor speed, whereas "flutter" is faster speed (a few tens of Hz) variations, usually caused by mechanical defects such as out-of-roundness of the capstanof a tape transport mechanism. The measurement is given in % and a lower number is better.
; Rumble : The measure of the low frequency (many tens of Hz) noise contributed by the turntable of an analogue playback system. It is caused by imperfect bearings, by uneven motor windings, by vibrations in driving bands in some turntables, by room vibrations (eg, from traffic) which is transmitted by the turntable mounting and so to the phono cartridge. A lower number is better.
Note that digital systems do not suffer from many of these effects at a signal level, though the same processes occur in the circuitry, since the data being handled is "symbolic". As long as the symbol survives the transfer between components, and can be perfectly regenerated (eg, by
pulse shapingtechniques) the data itself is perfectly maintained. The data is typically buffered in a memory, and is clocked out by a very precise crystal oscillator. The data usually does not degenerate as it passes through many stages, because each stage regenerates new symbols for transmission.
But digital systems have their own problems. Digitizing adds noise which is measurable, and which depends on the resolution ('number of bits") of the system, regardless of other quality issues. Clock timing errors (
jitter) result in non-linear distortion of the signal. The quality measurement for a digital system centers on the probability of an error in transmission or reception. Otherwise the quality of the system is defined more by design intent (ie, specifications) than measurements, such as the sample rateand bit depth. In general, digital systems are much less prone to error than analog systems. However, nearly all digital systems contain analog inputs and/or outputs, and certainly all of those which interact with the analog world do so. These analog components of the digital system can suffer analog effects and potentially compromise the integrity of a well designed digital system.
Jitter: A measurement of the variation in period between clock cycles, which should theoretically be exactly the same period. Less jitter is better.
Sample rate: A specification of the rate at which measurements are taken of the analog signal. This is measured in samples per second, or hertz. A higher sampling rate allows a greater total bandwidth or flatband frequency response. It can also reduce the effects of jitter.
Bit depth: A specification of the accuracy of each measurement. For example, a 3-bit system would be able to measure 23 = 8 different levels, so it would round the actual level at each point to the nearest representable. Typical values for audio are 8-bit, 16-bit, 24-bit, and 32-bit. The bit depth determines the theoretical maximum signal-to-noise ratio or dynamic range for the system. It is common for devices to create more noise than the minimum possible noise floor, however. Sometimes this is done intentionally; dithernoise is added to decrease the negative effects of quantization noiseby converting it into a higher level of uncorrelated noise.
:To calculate the maximum theoretical dynamic range of a digital system, find the total number of levels in the system. Dynamic Range = 20·log(# of different levels). Note: the log function has a base of 10. Example: An 8-bit system has 256 different possibilities, from 0 – 255. The smallest signal is 1 and the largest is 255. Dynamic Range = 20·log(255) = 48 dB.
; Sample accuracy/synchronization : Not as much a specification as an ability. Since independent digital audio devices are each run by their own
crystal oscillator, and no two crystals are exactly the same, the sample rate will be slightly different. This will cause the devices to drift apart over time. The effects of this can vary. If one digital device is used to monitor another digital device, this will cause dropouts in the audio, as one device will be producing more or less data than the other per unit time. If two independent devices record at the same time, one will lag the other more and more over time. This effect can be circumvented with a wordclocksynchronization.
; Linearity : "Differential non-linearity" and "integral non-linearity" are two measurements of the accuracy of an
analog-to-digital converter. Basically, they measure how close the threshold levels for each bit are to the theoretical equally-spaced levels.
audiophiles have postulated that the present set of audio measurements, as exemplified by the above list, do not fully represent all that is significant in accurate music reproduction, and instead represent only those aspects which are relatively simple and cost-effective to measure. Given the complexity and sophistication of human hearingand perception, some consideration should be given to the possibility that there may be aspects of audio that do not lend themselves to convenient measurement and simple interpretation, so have yet to be included in typical specifications.Fact|date=October 2008
All of the above measurements are
quantitative, rather than qualitative. Subjectivists claim that listening tests are more appropriate for appraising the 'quality' of an audio system than measuring the accuracy with which it can reproduce a waveform. Objectivitists counterclaim that repeated double-blind testing, using highly qualified listeners, consistently demonstrates that the current suit of measurements are more accurate and reliable than personal, subjective opinion.Fact|date=October 2008
Audio quality measurement
High fidelity, especially the
Physics of music
* [http://www.maxim-ic.com/appnotes.cfm/appnote_number/283 Explanation of INL/DNL measurements]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Audio quality measurement — seeks to quantify the various forms of corruption present in an audio system or device. The results of such measurement are used to maintain standards in broadcasting, to compile specifications, and to compare pieces of equipment. The need for… … Wikipedia
Audio noise measurement — is carried out when assessing the quality of audio equipment, such as is used in recording studios, broadcast studios, and in the home (Hi Fi).Noise in general refers to unwanted sound, often loud, but in audio systems it is the low level hiss or … Wikipedia
Audio power — Sound measurements Sound pressure p, SPL Particle velocity v, SVL Particle displacement ξ Sound intensity I, SIL Sound power Pac Sound power level SWL Sound energy Sound energy density … Wikipedia
Audio equipment testing — is done to provide consumers with an idea of what they are looking for and to make the process of equipment selection easier. The results are published in specialty electronics magazines, online, and in other media. Many people involved in the… … Wikipedia
Audio amplifier — An audio amplifier is an electronic amplifier that amplifies low power audio signals (signals composed primarily of frequencies between 20 hertz to 20,000 hertz, the human range of hearing) to a level suitable for driving loudspeakers and is the… … Wikipedia
Sound reinforcement system — A sound reinforcement system is an arrangement of microphones, electronic signal processors, amplifiers, and loudspeakers that makes live or pre recorded sounds usually music or speech louder, or that distributes the sound to a larger or more… … Wikipedia
Global Positioning System — GPS redirects here. For other uses, see GPS (disambiguation). Geodesy Fundamentals … Wikipedia
High-end audio — is a term used to describe higher priced and/or higher quality audio equipment. Definition of high end High end audio can refer to the build quality of the components, but more specifically, refers to the ability to reproduce a recording with the … Wikipedia
Constant voltage speaker system — Constant voltage speaker systems refer to networks of loudspeakers which are connected to an audio amplifier using step up and step down transformers to simplify impedance calculations and to minimize power loss over the speaker cables. They are… … Wikipedia
Connectors for car audio — Several types of connectors for car audio systems is used. Contents 1 ISO 10487 1.1 Power (A) 1.2 Loudspeaker (B) 1.3 Miscellaneous (C) … Wikipedia