RC circuit

RC circuit
Linear analog electronic filters
edit

A resistor–capacitor circuit (RC circuit), or RC filter or RC network, is an electric circuit composed of resistors and capacitors driven by a voltage or current source. A first order RC circuit is composed of one resistor and one capacitor and is the simplest type of RC circuit.

RC circuits can be used to filter a signal by blocking certain frequencies and passing others. The four most common RC filters are the high-pass filter, low-pass filter, band-pass filter, and band-stop filter.

Contents

Introduction

There are three basic, linear passive lumped analog circuit components: the resistor (R), the capacitor (C), and the inductor (L). These may be combined in the RC circuit, the RL circuit, the LC circuit, and the RLC circuit, with the abbreviations indicating which components are used. These circuits, among them, exhibit a large number of important types of behaviour that are fundamental to much of analog electronics. In particular, they are able to act as passive filters. This article considers the RC circuit, in both series and parallel forms, as shown in the diagrams below.

This article relies on knowledge of the complex impedance representation of capacitors and on knowledge of the frequency domain representation of signals.

Natural response

The simplest RC circuit is a capacitor and a resistor in series. When a circuit consists of only a charged capacitor and a resistor, the capacitor will discharge its stored energy through the resistor. The voltage across the capacitor, which is time dependent, can be found by using Kirchhoff's current law, where the current through the capacitor must equal the current through the resistor. This results in the linear differential equation


C\frac{dV}{dt} + \frac{V}{R}=0
.

Solving this equation for V yields the formula for exponential decay:


V(t)=V_0 e^{-\frac{t}{RC}} \ ,

where V0 is the capacitor voltage at time t = 0.

The time required for the voltage to fall to \frac{V_0}{e} is called the RC time constant and is given by

 \tau = RC \ .

Complex impedance

The complex impedance, ZC (in ohms) of a capacitor with capacitance C (in farads) is

Z_C = \frac{1}{sC}

The complex frequency s is, in general, a complex number,

s \ = \ \sigma + j \omega

where

j2 = − 1

Sinusoidal steady state

Sinusoidal steady state is a special case in which the input voltage consists of a pure sinusoid (with no exponential decay). As a result,


\sigma \ = \ 0

and the evaluation of s becomes


s \ = \  j \omega

Series circuit

Series RC circuit

By viewing the circuit as a voltage divider, the voltage across the capacitor is:


V_C(s) =  \frac{1/Cs}{R + 1/Cs}V_{in}(s) = \frac{1}{1 + RCs}V_{in}(s)

and the voltage across the resistor is:


V_R(s) = \frac{R}{R + 1/ Cs}V_{in}(s) = \frac{ RCs}{1 + RCs}V_{in}(s)
.

Transfer functions

The transfer function from the input voltage to the voltage across the capacitor is


H_C(s) = { V_C(s) \over V_{in}(s) }   = { 1 \over 1 + RCs  } 
.

Similarly, the transfer function from the input to the voltage across the resistor is


H_R(s) = { V_R(s) \over V_{in}(s) }   = { RCs \over 1 + RCs  }
.

Poles and zeros

Both transfer functions have a single pole located at


s = - {1 \over RC }
.

In addition, the transfer function for the resistor has a zero located at the origin.

Gain and phase angle

The magnitude of the gains across the two components are:


G_C = | H_C(j \omega) | = \left|\frac{V_C(j \omega)}{V_{in}(j \omega)}\right| = \frac{1}{\sqrt{1 + \left(\omega RC\right)^2}}

and


G_R = | H_R(j \omega) | = \left|\frac{V_R(j \omega)}{V_{in}(j \omega)}\right| = \frac{\omega RC}{\sqrt{1 + \left(\omega RC\right)^2}}
,

and the phase angles are:


\phi_C =  \angle H_C(j \omega) =  \tan^{-1}\left(-\omega RC\right)

and


\phi_R = \angle H_R(j \omega) =  \tan^{-1}\left(\frac{1}{\omega RC}\right)
.

These expressions together may be substituted into the usual expression for the phasor representing the output:


V_C \ = \ G_{C}V_{in}  e^{j\phi_C}

V_R \ = \  G_{R}V_{in} e^{j\phi_R}
.

Current

The current in the circuit is the same everywhere since the circuit is in series:


I(s) = \frac{V_{in}(s) }{R + \frac{1}{Cs}}  =  { Cs \over 1 + RCs } V_{in}(s)

Impulse response

The impulse response for each voltage is the inverse Laplace transform of the corresponding transfer function. It represents the response of the circuit to an input voltage consisting of an impulse or Dirac delta function.

The impulse response for the capacitor voltage is


h_C(t) = {1 \over RC} e^{-t / RC} u(t)  =  { 1 \over \tau} e^{-t / \tau} u(t)

where u(t) is the Heaviside step function and


\tau \ = \ RC

is the time constant.

Similarly, the impulse response for the resistor voltage is


h_R(t) = \delta (t) - {1 \over RC} e^{-t / RC} u(t)  =  \delta (t) - { 1 \over \tau} e^{-t / \tau} u(t)

where δ(t) is the Dirac delta function

Frequency-domain considerations

These are frequency domain expressions. Analysis of them will show which frequencies the circuits (or filters) pass and reject. This analysis rests on a consideration of what happens to these gains as the frequency becomes very large and very small.

As \omega \to \infty:

G_C \to 0
G_R \to 1.

As \omega \to 0:

G_C \to 1
G_R \to 0.

This shows that, if the output is taken across the capacitor, high frequencies are attenuated (rejected) and low frequencies are passed. Thus, the circuit behaves as a low-pass filter. If, though, the output is taken across the resistor, high frequencies are passed and low frequencies are rejected. In this configuration, the circuit behaves as a high-pass filter.

The range of frequencies that the filter passes is called its bandwidth. The point at which the filter attenuates the signal to half its unfiltered power is termed its cutoff frequency. This requires that the gain of the circuit be reduced to

G_C = G_R = \frac{1}{\sqrt{2}}.

Solving the above equation yields

\omega_{c} = \frac{1}{RC} \ \mathrm{rad/s}

or

f_c = \frac{1}{2\pi RC} \ \mathrm{Hz}

which is the frequency that the filter will attenuate to half its original power.

Clearly, the phases also depend on frequency, although this effect is less interesting generally than the gain variations.

As \omega \to 0:

\phi_C \to 0
\phi_R \to 90^{\circ} = \pi/2^{c}.

As \omega \to \infty:

\phi_C \to -90^{\circ} = -\pi/2^{c}
\phi_R \to 0

So at DC (0 Hz), the capacitor voltage is in phase with the signal voltage while the resistor voltage leads it by 90°. As frequency increases, the capacitor voltage comes to have a 90° lag relative to the signal and the resistor voltage comes to be in-phase with the signal.

Time-domain considerations

This section relies on knowledge of e, the natural logarithmic constant.

The most straightforward way to derive the time domain behaviour is to use the Laplace transforms of the expressions for VC and VR given above. This effectively transforms j\omega \to s. Assuming a step input (i.e. Vin = 0 before t = 0 and then Vin = V afterwards):


V_{in}(s) = V\frac{1}{s}

V_C(s) = V\frac{1}{1 + sRC}\frac{1}{s}

and


V_R(s) = V\frac{sRC}{1 + sRC}\frac{1}{s}
.
Capacitor voltage step-response.
Resistor voltage step-response.

Partial fractions expansions and the inverse Laplace transform yield:


\,\!V_C(t) = V\left(1 - e^{-t/RC}\right)

\,\!V_R(t) = Ve^{-t/RC}
.

These equations are for calculating the voltage across the capacitor and resistor respectively while the capacitor is charging; for discharging, the equations are vice-versa. These equations can be rewritten in terms of charge and current using the relationships C=Q/V and V=IR (see Ohm's law).

Thus, the voltage across the capacitor tends towards V as time passes, while the voltage across the resistor tends towards 0, as shown in the figures. This is in keeping with the intuitive point that the capacitor will be charging from the supply voltage as time passes, and will eventually be fully charged.

These equations show that a series RC circuit has a time constant, usually denoted τ = RC being the time it takes the voltage across the component to either rise (across C) or fall (across R) to within 1 / e of its final value. That is, τ is the time it takes VC to reach V(1 − 1 / e) and VR to reach V(1 / e).

The rate of change is a fractional \left(1 - \frac{1}{e}\right) per τ. Thus, in going from t = Nτ to t = (N + 1)τ, the voltage will have moved about 63.2 % of the way from its level at t = Nτ toward its final value. So C will be charged to about 63.2 % after τ, and essentially fully charged (99.3 %) after about . When the voltage source is replaced with a short-circuit, with C fully charged, the voltage across C drops exponentially with t from V towards 0. C will be discharged to about 36.8 % after τ, and essentially fully discharged (0.7 %) after about . Note that the current, I, in the circuit behaves as the voltage across R does, via Ohm's Law.

These results may also be derived by solving the differential equations describing the circuit:


\frac{V_{in} - V_C}{R} = C\frac{dV_C}{dt}

and


\,\!V_R = V_{in} - V_C
.

The first equation is solved by using an integrating factor and the second follows easily; the solutions are exactly the same as those obtained via Laplace transforms.

Integrator

Consider the output across the capacitor at high frequency i.e.

\omega \gg \frac{1}{RC}.

This means that the capacitor has insufficient time to charge up and so its voltage is very small. Thus the input voltage approximately equals the voltage across the resistor. To see this, consider the expression for I given above:


I = \frac{V_{in}}{R+1/j\omega C}

but note that the frequency condition described means that


\omega C \gg \frac{1}{R}

so


I \approx \frac{V_{in}}{R}
which is just Ohm's Law.

Now,


V_C = \frac{1}{C}\int_{0}^{t}Idt

so


V_C \approx \frac{1}{RC}\int_{0}^{t}V_{in}dt
,

which is an integrator across the capacitor.

Differentiator

Consider the output across the resistor at low frequency i.e.,


\omega \ll \frac{1}{RC}
.

This means that the capacitor has time to charge up until its voltage is almost equal to the source's voltage. Considering the expression for I again, when


R \ll \frac{1}{\omega C}
,

so


I \approx \frac{V_{in}}{1/j\omega C}

V_{in} \approx \frac{I}{j\omega C} = V_C

Now,


V_R = IR = C\frac{dV_C}{dt}R

V_R \approx RC\frac{dV_{in}}{dt}

which is a differentiator across the resistor.

More accurate integration and differentiation can be achieved by placing resistors and capacitors as appropriate on the input and feedback loop of operational amplifiers (see operational amplifier integrator and operational amplifier differentiator).

Parallel circuit

Parallel RC circuit

The parallel RC circuit is generally of less interest than the series circuit. This is largely because the output voltage Vout is equal to the input voltage Vin — as a result, this circuit does not act as a filter on the input signal unless fed by a current source.

With complex impedances:


I_R = \frac{V_{in}}{R}\,

and


I_C = j\omega C V_{in}\,
.

This shows that the capacitor current is 90° out of phase with the resistor (and source) current. Alternatively, the governing differential equations may be used:


I_R = \frac{V_{in}}{R}

and


I_C = C\frac{dV_{in}}{dt}
.

When fed by a current source, the transfer function of a parallel RC circuit is


\frac{V_{out}}{I_{in}} = \frac{R}{1+sRC}
.

See also

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • circuit — [ sirkɥi ] n. m. • 1257; circuite n. f. 1220; lat. circuitus, de circuire, circumire « faire le tour » 1 ♦ Vieilli Distance à parcourir pour faire le tour d un lieu. ⇒ contour, périmètre, pourtour, 3. tour. Le parc a quatre kilomètres de circuit …   Encyclopédie Universelle

  • Circuit court — is the name of court systems in several common law jurisdictions. Contents 1 History 2 Republic of Ireland 3 United States 3.1 Federal courts of appeals …   Wikipedia

  • Circuit Automobile De La Sarthe — Circuit des 24 Heures Circuit des 24 Heures …   Wikipédia en Français

  • Circuit automobile de la Sarthe — Circuit des 24 Heures Circuit des 24 Heures …   Wikipédia en Français

  • Circuit automobile de la sarthe — Circuit des 24 Heures Circuit des 24 Heures …   Wikipédia en Français

  • Circuit de la Sarthe automobile — Circuit des 24 Heures Circuit des 24 Heures …   Wikipédia en Français

  • Circuit des 24 heures — Circuit des 24 Heures …   Wikipédia en Français

  • Circuit du lac d'Aix les Bains — Le circuit du lac d Aix les Bains était tracé au bord du lac d’Aix les Bains. Long de 2 400 mètres, il se situait autour de l’endroit où se …   Wikipédia en Français

  • Circuit du lac d'Aix-les-Bains — Le circuit du lac d Aix les Bains était tracé au bord du lac d’Aix les Bains. Long de 2 400 mètres, il se situait autour de l’endroit où se trouve actuellement le carrefour du Lac …   Wikipédia en Français

  • Circuit Park Zandvoort — Zandvoort today Location Burgemeester van Alphenstraat 108, 2041 KP Zandvoort, Netherlands Time zone CET (UTC+01) Major events …   Wikipedia

  • Circuit de Nevers Magny-Cours — bis 1987 Circuit Jean Behra Adresse: Circuit de Nevers Magny Cours Technopôle 58 470 Magny Cours …   Deutsch Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”