- Constant speed propeller
Constant speed propeller Cutaway constant speed propeller hub
A constant speed propeller is a type of propeller that can change its blade pitch to take better advantage of the power supplied by an engine in much the same way that a transmission in a car takes better advantage of its power source. The mechanism varies depending on the aircraft, but the effect is to change the angle of attack of the propeller blades to take a smaller or larger "bite" of air as it rotates.
An airplane propeller operates as the source of thrust that moves the plane forward.
When an airplane is stationary with the propeller spinning (in calm air), air flows past the narrow leading edge of the propeller. This is the most efficient configuration as the drag forces on the propeller are the lowest. As the airplane starts moving forward, the airflow begins to push against the front, wider cross section of the propeller, creating greater drag.
A constant-speed propeller is able to rotate along the longest axis of the blade to take a sharper bite of air with respect to the airplane, allowing the propeller to maintain the most efficient orientation to the airflow around it. This balances the tradeoff that fixed-pitch propellers must make between high take-off performance and high cruise performance.
A shallower angle of attack requires the least horsepower, but the highest RPM because the propeller is not moving very much air with each revolution. This is similar to a car operating in low gear: when you get up to speed you want to slow down the engine while still producing enough power to keep the vehicle moving. This is accomplished in an airplane by increasing the angle of attack of the propeller. This means that the propeller moves more air per revolution and allows the engine to spin slower while moving an equivalent volume of air, thus maintaining velocity.
The first attempts at constant-speed propellers were called counterweight propellers which were driven by mechanisms which operated on centrifugal force. A counterbalance was set up near or in the spinner, held in by a spring. When the propeller reached a certain RPM, centrifugal force would cause these counterbalances to swing outwards, which would drive a mechanism that twisted the propeller into a steeper pitch. When the airplane slowed down, the RPM would decrease enough for the spring to push the counterweights back in, realigning the propeller to the shallower pitch.
In newer models of constant-speed propellers, oil is pumped through the propeller shaft to push on a piston which drives the mechanism to change pitch. The flow of oil and the pitch is controlled by a governor, consisting of a speeder spring, fly weights, and a pilot valve. The tension of the speeder spring is set by the prop control lever, which sets the RPMs. The governor will maintain that RPM setting until an overspeed or underspeed condition exists. When an overspeed condition occurs, the propeller begins to rotate faster than the desired RPM setting. This would occur as the plane descends and airspeed increases. The fly weights begin to pull outward due to centrifugal force which further compresses the speeder spring. As that happens, the piston moves forward allowing the pilot valve to open and oil to flow from the oil sump into the hub. This increase in oil pressure will increase the pitch of the propeller angle causing it to slow back down to the desired RPM setting. When an underspeed condition occurs, as in a climb with loss of airspeed, just the opposite takes place. The airspeed decreases causing the propeller to slow down. This will cause the fly weights to move inward due to a lack in centrifugal force and tension will be released from the speeder spring. As this happens, the piston will move in the opposite direction causing the pilot valve to allow oil to flow from the hub back to the oil sump. The propeller blade angle will now decrease to a lower pitch allowing the propeller to speed back up to the desired RPM setting. This process usually takes place frequently throughout flight.
All high-performance aircraft have constant-speed propellers as they vastly improve fuel efficiency and performance, especially at high altitude.
Constant speed units
A constant speed unit (CSU) or propeller governor is the device fitted to one of these propellers to automatically change its pitch so as to attempt to keep engine speed constant. Most engines produce their maximum power in a narrow speed band. The CSU can be said to be to an aircraft what the CVT is to the motor car: the engine can be kept running at its optimum speed no matter what speed the aircraft is flying through the air. The advent of the CSU had another benefit: it allowed the designers of aircraft engines to keep ignition systems simple - the automatic spark advance seen in motor vehicle engines is much simplified in aircraft engines.
Three methods are used to vary the pitch. Engine oil pressure is the usual mechanism used in commercial aircraft and the Continental and Lycoming engines fitted to light aircraft. Alternatively or additionally centrifugal weights may be attached directly to the propeller as in the Yak-52. Small modern engines such as the Rotax 912 which have a CSU may use either the traditional hydraulic method or an electrical pitch control mechanism. A pilot requires some additional training and, in most jurisdictions, a formal signoff before being allowed to fly aircraft fitted with a CSU. CSUs are not allowed to be fitted to aircraft certified under the USA Light-sport Aircraft regulations.
- Variable pitch propeller – where the pitch is manually selected by the pilot
- http://www.pilotfriend.com/aero_engines/aero_eng_dvmt.htm, Kimble D. McCutcheon
Aircraft piston engine components, systems and terminology Piston engines
- Mechanical components
Camshaft · Connecting rod · Crankpin · Crankshaft · Cylinder · Cylinder head · Gudgeon pin · Hydraulic tappet · Main bearing · Obturator ring · Oil pump · Piston · Piston ring · Poppet valve · Pushrod · Rocker arm · Sleeve valve · Tappet
- Electrical components
Air-cooled · Bore · Compression ratio · Dead centre · Engine displacement · Four-stroke engine · Horsepower · Ignition timing · Manifold pressure · Mean effective pressure · Naturally-aspirated · Monosoupape · Overhead camshaft · Overhead valve · Rotary engine · Shock-cooling · Stroke · Time between overhaul · Two-stroke engine · Valve timing · Volumetric efficiency
Propellers Engine instruments Engine controls Fuel and induction system Other systems Aircraft gas turbine engine components, systems and terminology Gas turbinesTypesMechanical
Annunciator panel · Electronic Centralised Aircraft Monitor (ECAM) · Electronic Flight Instrument System (EFIS) · Engine Indicating and Crew Alerting System (EICAS) · Flight data recorder · Glass cockpit
Engine controls Fuel and induction
Other systems Lists relating to aviation General Military Accidents/incidents Records
Wikimedia Foundation. 2010.
Look at other dictionaries:
constant-speed propeller — A propeller in which the pitch is adjusted automatically, so that the propeller revolves at a given rate dictated by the pilot and remains at that rate irrespective of maneuvers or throttle position. The pitch of the propeller is altered suitably … Aviation dictionary
Constant Speed Drive — Mechanism CSDs are mainly used on airliner and military aircraft jet engines to drive the alternating current (AC) electrical generator. In order to produce the proper voltage at a constant AC frequency, usually 3 phase 115 VAC at 400 Hz, a… … Wikipedia
constant-speed unit — An engine driven unit used for variable pitch propellers. A CSU automatically permits adjustment of the pitch for varying the speed and power. This allows the propeller to operate more efficiently at any selected combination of RPM, manifold… … Aviation dictionary
Propeller — A propeller is essentially a type of fan which transmits power by converting rotational motion into thrust for propulsion of a vehicle such as an aircraft, ship, or submarine through a mass such as water or air, by rotating two or more twisted… … Wikipedia
Propeller governor — History = In the history of development of the airplane it became apparent that it is necessary to improve aircraft performance. One of influential factors was the propeller design in relation to the most efficient blade angle. The first… … Wikipedia
Constant-velocity joint — Rzeppa six ball CV joint Constant velocity joints (aka homokinetic or CV joints) allow a drive shaft to transmit power through a variable angle, at constant rotational speed, without an appreciable increase in friction or play. They are mainly… … Wikipedia
propeller governor — A device that keeps the propeller speed constant irrespective of the forward speed and power. The governor is usually centrifugal and keeps the shuttle valve oscillating about the null position feeding oil to change the propeller pitch and thus… … Aviation dictionary
Controllable pitch propeller — A controllable pitch propeller (CPP) or variable pitch propeller is a type of propeller with blades that can be rotated around their long axis to change their pitch. If the pitch can be set to negative values, the reversible propeller can also… … Wikipedia
controllable-pitch propeller — A propeller whose pitch can be altered by the pilot in flight. Unlike in a constant speed propeller, where the governor automatically controls the pitch, here the pilot carries out the pitch adjustments. Takeoff is made with a low blade angle, so … Aviation dictionary
Controllable Pitch-Propeller — Ein Verstellpropeller Verstellpropeller sind Propeller, bei denen der Einstellwinkel der Propellerblätter variabel ist, wodurch der Anstellwinkel der Blätter an verschiedene Betriebssituationen angepasst werden kann. Verstellpropeller kommen als… … Deutsch Wikipedia