Solder


Solder

A solder is a fusible metal alloy with a melting point or melting range of 90 to 450 °C (200 to 840 °F), used in a process called soldering where it is melted to join metallic surfaces. It is especially useful in electronics and plumbing. Alloys that melt between 180 and 190 °C are the most commonly used.

The word solder comes from the Middle English word "soudur", via Old French "solduree" and "soulder", from the Latin "solidare", meaning '‘to make solid’'. Solder can contain lead and or flux but in many applications solder is now lead free.

----

Lead solder

Tin/lead solders are commercially available with tin concentrations between 5% and 70% by weight. The greater the tin concentration, the greater the solder’s tensile and shear strengths. At the retail level, the two most common alloys are 60/40 Sn/Pb and 63/37 Sn/Pb used principally in electrical work. The 63/37 ratio is notable in that it is a eutectic mixture, which means:
# It has the lowest melting point (183 °C or 361.4 °F) of all the tin/lead alloys; and
# The melting point is truly a "point" — not a range

At a eutectic composition, the liquid solder solidifies as a eutectic, which consists of fine grains of nearly pure lead and nearly pure tin phases, but in no way is it an intermetallic, since there are no tin/lead intermetallics, as can be seen from a tin/lead equilibrium diagram. [cite web|url=http://pwatlas.mt.umist.ac.uk/internetmicroscope/micrographs/microstructures/more-metals/lead.html |title=Internet Microscope for Schools : Micrographs : Lead |publisher=Pwatlas.mt.umist.ac.uk |date= |accessdate=2008-09-22]

In plumbing, a higher proportion of lead was used. This had the advantage of making the alloy solidify more slowly, so that it could be wiped over the joint to ensure watertightness. Although lead water pipes were displaced by copper when the significance of lead poisoning began to be fully appreciated, lead solder was still used until the 1980s because it was thought that the amount of lead that could leach into water from the solder was negligible. Since even small amounts of lead have been found detrimental to health,Fact|date=August 2008 lead in plumbing solder was replaced by copper or antimony, with silver often added, and the proportion of tin was increased (see "Lead-free solder.)

Hard solder

As used for brazing, is generally a copper/zinc or copper/silver alloy, and melts at higher temperatures.

In silversmithing or jewelry making, special hard solders are used that will pass assay. They contain a high proportion of the metal being soldered and lead is not used in these alloys. These solders also come in a variety of hardnesses, known as 'enamelling', 'hard', 'medium' and 'easy'. Enamelling solder has a high melting point, close to that of the material itself, to prevent the joint desoldering during firing in the enamelling process. The remaining solder types are used in decreasing order of hardness during the process of making an item, to prevent a previously soldered seam or joint desoldering while soldering a new joint. Easy solder is also often used for repair work for the same reason. Flux or rouge is also used to prevent joints desoldering.

Silver solder is also used in manufacturing, when there is a need to join metal parts that cannot be welded. The alloys used for these purposes contain a high proportion of silver (up to 40%), and may also contain toxic cadmium.

Flux core solder

Solder often comes pre-mixed with, or is used with, flux, a reducing agent designed to help remove impurities (specifically oxidised metals) from the points of contact to improve the electrical connection. For convenience, solder is often manufactured as a hollow tube and filled with flux. Most cold solder is soft enough to be rolled and packaged as a coil, making for a convenient and compact solder/flux package. The two principal types of flux are acid flux, used for metal mending, and rosin flux, used in electronics, where the corrosiveness of the vapours that arise when acid flux is heated could damage components. Due to concerns over atmospheric pollution and hazardous waste disposal, the electronics industry has been gradually shifting from rosin flux to water-soluble flux, which can be removed with deionised water and detergent, instead of hydrocarbon solvents.

Lead-free solder

On July 1 2006 the European Union Waste Electrical and Electronic Equipment Directive (WEEE) and Restriction of Hazardous Substances Directive (RoHS) came into effect prohibiting the intentional addition of lead to most consumer electronics produced in the EU. No such legislation is in place in the United States or other countries, however manufacturers may receive tax benefits by reducing the use of lead-based solder. Lead-free solders in commercial use may contain tin, copper, silver, bismuth, indium, zinc, antimony, and traces of other metals. Most lead-free replacements for conventional Sn60/Pb40 and Sn63/Pb37 solder have melting points from 5–20 °C higher, though solders with much lower melting points are available. Drop-in replacements for silkscreen with solder paste soldering operations are available. Minor modification to the solder pots (e.g. titanium liners and/or impellers) used in wave-soldering operations may be desired to reduce maintenance costs associated with the increased tin-scavenging effects of high tin solders. The properties of lead-free solders are not as thoroughly known and may therefore be considered less reliable in select applications, e.g. Hi-rel aerospace and life-critical medical. "Tin whiskers" were a problem with early electronic solders which were coincidentally lead-free, and lead was initially added in part to eliminate them. These problems are negligible in modern alloys,Fact|date=June 2008 however, except in hi-rel military, aerospace-satellite and life-critical medical applications.

* SnAgCu solders are used by two thirds of Japanese manufacturers for reflow and wave soldering, and by about ¾ companies for hand soldering.
** SnAg3.0Cu0.5, tin with 3% silver and 0.5% copper, has a melting point of 217 to 220 °C and is predominantly used in Japan. It is the JEITA recommended alloy for wave and reflow soldering, with alternatives SnCu for wave and SnAg and SnZnBi for reflow soldering.
** SnAg3.5Cu0.7 is another commonly used alloy, with melting point of 217-218 °C.
** SnAg3.5Cu0.9, with melting point of 217 °C, is determined by NIST to be truly eutectic.
** SnAg3.8Cu0.7, with melting point 217-218 °C, is preferred by the European IDEALS consortium for reflow soldering.
** SnAg3.8Cu0.7Sb0.25 is preferred by the European IDEALS consortium for wave soldering.
** SnAg3.9Cu0.6, with melting point 217-223 °C, is recommended by the US NEMI consortium for reflow soldering.
* SnCu0.7, with melting point of 227 °C, is a cheap alternative for wave soldering, recommended by the US NEMI consortium.
* SnZn9, with melting point of 199 °C, is a cheaper alloy but is prone to corrosion and oxidation.
* SnZn8Bi3, with melting point of 191-198 °C, is also prone to corrosion and oxidation due to its zinc content.
* SnSb5, tin with 5% of antimony, is the US plumbing industry standard. Its melting point is 232-240 °C. It displays good resistance to thermal fatigue and good shear strength.
* SnAg2.5Cu0.8Sb0.5 melts at 217-225 °C and is patented by AIM alliance.
* SnIn8.0Ag3.5Bi0.5 melts at 197 to 208 °C and is patented by Matsushita/Panasonic.
* SnBi57Ag1 melts at 137-139 °C and is patented by Motorola.
* SnBi58 melts at 138 °C.
* SnIn52 melts at 118 °C and is suitable for the cases where low-temperature soldering is needed.

Different elements serve different roles in the solder alloy:
* Silver provides mechanical strength, but has worse ductility than lead. In absence of lead, it improves resistance to fatigue from thermal cycles.
* Copper lowers the melting point, improves resistance to thermal cycle fatigue, and improves wetting properties of the molten solder. It also slows down the rate of dissolution of copper from the board and part leads in the liquid solder.
* Bismuth significantly lowers the melting point and improves wettability. In presence of sufficient lead and tin, bismuth forms crystals of Sn16Pb32Bi52 with melting point of only 95 °C, which diffuses along the grain boundaries and may cause a joint failure at relatively low temperatures. A high-power part pre-tinned with an alloy of lead can therefore desolder under load when soldered with a bismuth-containing solder.
* Indium lowers the melting point and improves ductility. In presence of lead it forms a ternary compound that undergoes phase change at 114 °C.
* Zinc lowers the melting point and is low-cost. However it is highly susceptible to corrosion and oxidation in air, therefore zinc-containing alloys are unsuitable for some purposes, e.g. wave soldering, and zinc-containing solder pastes have shorter shelf life than zinc-free.
* Antimony is added to increase strength without affecting wettability.

ee also

*Soldering
*Solder paste
*Solder sucker
*Solderability
*Soldering gun
*Soldering iron
*Welding
*Brazing

References

External links

* [http://www.solderinguide.com/ SolderingGuide.com]
* [http://alpha.cooksonelectronics.com/products/paste/index.asp Solder Paste Selector Guide]
* [http://www.indium.com/products/alloychart.php Physical Properties Table: Specialty Alloys and Solders]
* [http://www.kester.com/en-us/leadfree/alloys.aspx Lead-free solder alloys]
* [http://www.bhavanimetals.com/Solder_Wire_Rosin_Core_Solder.htm Common Solder alloys and their melting ranges]
* [http://www.metallurgy.nist.gov/phase/solder/solder.html Phase Diagrams of different types of solder alloys]
* [http://www.sentryair.com/solder-fumes.htm Solder Fumes Dangers by Sentry Air Systems]
* [http://mtdata.software.googlepages.com/periodictableSolders.htm Phase diagrams for lead free solders]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • solder — 1. (sol dé) v. a. 1°   Donner une solde à des troupes, les avoir à sa solde. 2°   Par extension, payer des gens pour faire quelque chose. Solder des chefs d émeute. ÉTYMOLOGIE    Solde 1 ; bas lat. solidare ; ital. soldare. Le prov. disait… …   Dictionnaire de la Langue Française d'Émile Littré

  • Solder — Sol der, n. [Formerly soder; F. soudure, OF. soudeure, fr. OF. & F. souder to solder, L. solidare to fasten, to make solid. See {Solid}, and cf. {Sawder}.] A metal or metallic alloy used when melted for uniting adjacent metallic edges or… …   The Collaborative International Dictionary of English

  • solder — [säd′ər] n. [ME soudre < OFr souldure < soulder, to make solid < L solidare < solidus, SOLID] 1. a metal alloy that is heated and used to join or patch metal parts or surfaces: soft solders of tin lead alloys melt easily; hard (or… …   English World dictionary

  • Solder — Sol der, v. t. [imp. & p. p. {Soldered}; p. pr. & vb. n. {Soldering}.] [Formerlysoder. See {Solder}, n.] 1. To unite (metallic surfaces or edges) by the intervention of a more fusible metal or metallic alloy applied when melted; to join by means… …   The Collaborative International Dictionary of English

  • solder — mid 14c., sawd, from O.Fr. soldure, from solder to join with solder, from L. solidare to make solid, from solidus solid (see SOLID (Cf. solid)). Modern form is from early 15c. The l is still pronounced in Great Britain. The noun is first attested …   Etymology dictionary

  • solder — ► NOUN ▪ a low melting alloy, especially one based on lead and tin, used for joining less fusible metals. ► VERB ▪ join with solder. ORIGIN Old French soudure, from Latin solidare fasten together …   English terms dictionary

  • Solder — Solder. См. Припой. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • solder — index cement, connect (join together) Burton s Legal Thesaurus. William C. Burton. 2006 …   Law dictionary

  • solder — 1. solder [ sɔlde ] v. tr. <conjug. : 1> • XVIe, repris en 1789; de 1. solde ♦ Vx Avoir (qqn) à sa solde. ⇒ payer. solder 2. solder [ sɔlde ] v. tr. <conjug. : 1> • 1675; de 2. solde; évince souder en ce sens (depuis 1636) repris de l …   Encyclopédie Universelle

  • Sölder — Hofrat Dr. Ludwig Sölder war ein österreichischer Gerechter unter den Völkern. Der Tiroler Ludwig Sölder aus Thaur bei Innsbruck bewahrte 1943 zwei jüdische Frauen in Jugoslawien vor dem Tod. Er war damals als 21 jähriger Leutnant der Wehrmacht… …   Deutsch Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.