Cat's-whisker detector


Cat's-whisker detector
Galena cat's whisker detector
Precision cat's whisker detector using iron pyrite crystal, early 1900s. The crystal is inside the metal capsule under the vertical needle "whisker" (right).

A cat’s whisker detector (sometimes called a crystal detector) is an antique electronic component consisting of a thin wire that lightly touches a crystal of semiconducting mineral to make a crude point-contact rectifier. Developed by early radio researchers Jagadish Chandra Bose, G. W. Pickard and others, this device was used as the detector in early crystal radios, from about 1906 through the Second World War. It gave this type of radio receiver its name. It was the first type of semiconductor diode, and in fact the first semiconductor electronic device. The term cat's whisker was also sometimes used to describe the crystal receiver itself. Cat's whisker detectors are obsolete and are now only used in antique or antique-reproduction radios.

Contents

Description

A small portable crystal radio, with a cat's whisker detector visible at top

The wire touching the surface of the crystal formed a crude and unstable metalsemiconductor or p-n point-contact junction, forming a Schottky barrier diode. This junction conducts electric current in only one direction and resists current flowing in the other direction. In a crystal radio, its function was to rectify the radio signal, converting it from alternating current to a pulsing direct current, to extract the audio signal (modulation) from the radio frequency carrier wave.

Only certain sites on the crystal surface functioned as rectifying junctions. Thus, the device was very sensitive to the exact geometry and pressure of contact between wire and crystal. Therefore it was made adjustable, and a usable point of contact was found by trial and error before each use. The wire was suspended from a moveable arm, and was dragged across the crystal face by the operator until the device began functioning. In a crystal radio, the operator would tune the radio to a strong local station if possible, and then adjust the cat's whisker until the station or static sounds was heard in the radio's earphones. This required some skill and a great deal of patience; even then a good contact could easily be lost by the slightest vibration. An alternate method of adjustment was to use a battery-operated buzzer to generate a test signal. The spark at the buzzer's contacts functioned as a weak radio transmitter, so when the crystal began functioning the buzz could be heard in the earphones, and the buzzer was turned off. The temperamental, unreliable action of the crystal detector was a barrier to its acceptance as a standard component in commercial radio equipment,[1] and was one reason for its rapid replacement by vacuum tubes after 1920. Frederick Seitz, a later semiconductor researcher, wrote:

Such variability, bordering on what seemed the mystical, plagued the early history of crystal detectors and caused many of the vacuum tube experts of a later generation to regard the art of crystal rectification as being close to disreputable.[2]

Crystal

Pictorial diagram with parts labelled; a horizontal wire antenna at top is connected to the top end of a coil with a sliding contact for tuning. The top end of the coil is connected through a cat's whisker detector to a set of headphones. The bottom end of the tuning coil is connected to ground, as is the second terminal of the headphones.
Diagram of a crystal set using a cat's-whisker detector.
Modern galena cat's whisker detector, showing parts. The galena crystal (upper left) is held in the metal capsule with a screw cap, leaving its face exposed.

A natural mineral crystal forms the semiconductor side of the junction. The most common crystal used was galena (PbS, lead sulfide), a naturally occurring ore of lead. Galena is a semiconductor with a small bandgap of about 0.4 eV, and is used without treatment directly as it is mined. Galena with good detecting properties is rare and has no reliable visual characteristics distinguishing it from galena samples with poor detecting properties. A rough pebble of detecting mineral about the size of a pea was mounted in a metal cup, which formed one side of the circuit. The electrical contact between the cup and the crystal had to be good, because this contact must not act as a second rectifying junction. To make good contact with the crystal, it was either clamped with setscrews or mounted in solder. Because the relatively high temperature of tin-lead solder can damage many crystals, a low melting point (well under 200°F) alloy such as Wood's metal was used. One surface was left exposed to allow contact with the cat's whisker wire.

Whisker

The "cat's whisker", a springy piece of thin metal wire, formed the metal side of the junction. Phosphor bronze wire of about 30 gauge was commonly used because it had the right amount of springiness. It was mounted on an adjustable arm with an insulated handle so that the entire exposed surface of the crystal could be probed from many directions to try to find the most sensitive spot. Cat's whiskers in simple detectors were straight or curved, but most professional cat's whiskers had a coiled section in the middle that served as a spring.[3] The crystal required just the right gentle pressure by the wire; too much pressure caused the device to conduct in both directions. Precision detectors often used a metal needle instead of a cat's whisker, mounted on a thumbscrew-operated leaf spring to adjust the pressure applied.

The first crystal detector commercially produced, Pickard's silicon detector, from 1906. Silicon didn't require the delicate "cat's whisker" contact.
A "Perikon" detector, 1914. Instead of a wire-to-crystal contact, this had a crystal-to-crystal contact. The bornite crystal (right) on the adjustable arm was moved forward until it touched one of the zincite crystals on the carousel (left). Multiple zincite crystals were provided because the zincite was vulnerable to damage from atmospheric electricity.
Precision detector using leaf spring and thumbscrew to control pressure
Pyrite detector
Galena detector on a French crystal radio

Types

How a crystal detector works in a radio receiver.[4][5] (A) The amplitude modulated radio signal from the receiver's tuning section. The rapid oscillations are the radio frequency carrier wave. The audio signal (the sound) is contained in the slow variations (modulation) of the size of the waves. This signal cannot be converted to sound by the earphone, because the audio excursions are the same on both sides of the axis, averaging out to zero, resulting in no net motion of the earphone's diaphragm. (B) The crystal conducts current in only one direction, stripping off the oscillations on one side of the signal, leaving a pulsing direct current whose amplitude does not average zero but varies with the audio signal. (C) A bypass capacitor across the earphone smoothes the waveform, removing the radio frequency carrier pulses, leaving the audio signal.

Historically, many other minerals and compounds besides galena were used for the crystal, the most important being iron pyrite ("fool's gold", iron disulfide), silicon, molybdenite (MoS2), and silicon carbide (carborundum, SiC). Some were used with gold or graphite "cat's whiskers". Another type had a crystal-to-crystal junction instead of a "cat's whisker", with two crystals mounted facing each other. One crystal was moved forward on an adjustable mount until the crystal faces touched. The most common of these was a zincite-bornite (ZnO-Cu5FeS4) junction trade-named Perikon, but zincite-chalcopyrite, silicon-arsenic and silicon-antimony junctions were also used. The goal of researchers was to find junctions that were not as sensitive to vibration and unreliable as galena and pyrite. Some of these other junctions, particularly carborundum, were stable enough that they used a more permanent spring-loaded contact rather than a "cat's whisker".[6] For this reason carborundum detectors were preferred in large commercial wireless stations, and military and shipboard stations which were subject to vibration from waves and gunnery exercises. Another quality desired was the ability to withstand high currents without damage, because in wireless stations the fragile detector junction could be "burned out" by atmospheric electric charge from the antenna, or high radio frequency current leaking into the receiver from the powerful spark-gap transmitter during transmissions. Carborundum detectors, which used large area contacts, were also particularly robust in this regard.

To increase sensitivity, some of these junctions such as silicon carbide were "biased" by connecting a battery and potentiometer across them to provide a small constant forward voltage across the junction.[7]

The oxide layers that form on many ordinary metal surfaces have semiconducting properties, and detectors for crystal radios have been improvised from a variety of everyday objects such as rusty needles and corroded pennies. The foxhole radio [5] was a crystal radio receiver improvised by soldiers during World War II without access to conventional sets. It used a razor blade and a safety pin or lead pencil to form a demodulating junction. Much patience was required to find an active detecting site on the blade. Stray rectifying junctions between metal parts of radio transmitter installations are still a source for interference, because they can radiate harmonics of the transmitter frequency.

History

The modern circuit symbol for a diode originated as a schematic drawing of a cat's whisker detector.

Unlike modern radio stations that transmit sound, the first radio transmitters during the first three decades of radio transmitted information by telegraphy, turning the transmitter on and off with a switch called a telegraph key to spell out messages in Morse code, consisting of "dots" and "dashes". So early radio receiving apparatus merely had to detect the presence or absence of the radio signal, not convert it into audio. The device that did this was called a detector. The crystal detector was the most successful of many detector devices that were used in the early days of radio. It replaced electrolytic, magnetic, and particularly coherer detectors in radio receivers around 1906. Later, when AM radio transmission was developed to transmit sound, around World War 1, crystal detectors proved able to receive this as well.

The "unilateral conduction" of crystals, as it was then called, was discovered by Ferdinand Braun, a German physicist in 1874 at the University of Würzburg, before radio had been invented. Based on this work G.W. Pickard developed the cat's whisker diode using a silicon crystal, which was patented in 1906. However, Bengali scientist Jagadish Chandra Bose was the first to use a crystal to detect radio waves, in his experiments with microwaves in 1894, applying for a patent on a galena detector in 1901.

When these devices were in common use, more advanced proprietary versions of "permanent" detectors were developed, many of them by G. W. Pickard, who tested more than 30,000 combinations of crystal and wire contacts.[8] One consisted of various combinations of pairs of different crystals such as Zincite touching Bornite or Chalcopyrite, in fairly heavily spring-loaded contact. Pickard named this the Perikon detector, from "PERfect pIcKard cONtact". Other detectors patented by Pickard included the common crystal iron pyrite. Pickard has the distinction of having brought silicon into use as a detector, patenting it in 1906. At nearly the same time, General Henry Harrison Chase Dunwoody patented the use of the silicon carbide (carborundum) detector, an artificial substance created accidentally during attempts by Edward Acheson to create diamonds.

Unamplified radio receivers, most of which were crystal radios, were the only way to receive radio signals during most of the wireless telegraphy era, which ended around 1920. Mineral detectors were largely superseded by vacuum tubes, invented in 1906, although the expense of tube receivers meant that full replacement took several decades. By the 1920s crystal radios were relegated to use by hobbyists and youth groups.

A crystal detector in commercial form from the 1960s

The point-contact semiconductor detector was subsequently resurrected around World War II because of the military requirement for microwave radar detectors. Vacuum tube detectors do not work at microwave frequencies. The small area of the point contact minimized minority carrier storage and capacitance, making these diodes fast enough to function at radar frequencies. Silicon and germanium point contact diodes were developed. Wartime research on PN junctions in crystals paved the way for the invention of the transistor in 1956.(Transistor#History 1947? Silicon transistor 1954?)[citation needed] The first transistors also used cat's whisker contacts.

The germanium diodes that became widely available after the war proved to be as sensitive as galena and didn't require any adjustment, so they replaced cat's whisker detectors in the few crystal radios still being made, largely putting an end to the manufacture of this antique radio component. Although cat's whisker detectors are obsolete, modern point-contact silicon detectors are still commercially produced.[9] Thus the point contact method used to make these first semiconductor diodes 100 years ago is still being used today.

Copies of original cat's-whisker detectors are still manufactured and sold, for antique radio hobbyists.

See also

 Newspaper clipping with photo showing a man wearing headphones and smoking a pipe; attached to the headphones is a diamond-shaped multiturn aerial, and the pipe bowl is wound with wire; the crystal detector is mounted on the pipe stem. Text in the clipping describes the photo and says this rig could pick up stations up to 10 miles away.
An early portable cat's-whisker radio set with aerial

References

  1. ^ Braun, Ernest; Stuart MacDonald (1982). Revolution in Miniature: The history and impact of semiconductor electronics, 2nd Ed.. UK: Cambridge Univ. Press. pp. 11–12. ISBN 9780521289030. http://books.google.com/books?id=03c4wldf-k4C&pg=PA11. 
  2. ^ Riordan, Michael; Lillian Hoddeson (1988). Crystal fire: the invention of the transistor and the birth of the information age. USA: W. W. Norton & Company. pp. 19–21. ISBN 0393318516. http://books.google.com/books?id=SZ6wm5ZSUmsC&pg=PA92. 
  3. ^ Sievers, Maurice L. (2008). Crystal Clear: Vintage American Crystal Sets, Crystal Detectors, and Crystals. Sonoran Publishing. pp. 6. ISBN 1886606013. http://books.google.com/books?id=2huyl5tOpWAC&pg=PA6. 
  4. ^ Marx & Van Muffling (1922) Radio Reception, p.43, fig.22
  5. ^ a b Campbell, John W. (October 1944). "Radio Detectors and How They Work". Popular Science (New York: Popular Science Publishing Co.) 145 (4): 206–209. http://books.google.com/books?id=PyEDAAAAMBAJ&pg=PA206&. Retrieved 2010-03-06. 
  6. ^ The Principles Underlying Radio Communication, 2nd Ed., Radio pamphlet no. 40. USA: Prepared by US National Bureau of Standards, United States Army Signal Corps. 1922. pp. 421–425. http://books.google.com/books?id=4JVEAAAAIAAJ&pg=PA422. 
  7. ^ Pender, Harold; William Arthur del Mar (1922). Handbook for Electrical Engineers, 2nd Ed.. New York: J. Wiley & Sons.. pp. 1268. http://books.google.com/books?id=t6JEAAAAIAAJ&pg=PA1268. 
  8. ^ Lee, Thomas H. (2004). Planar Microwave Engineering: A practical guide to theory, measurements, and circuits. UK: Cambridge Univ. Press. pp. 297–300. ISBN 9780521835268. http://books.google.com/books?id=uoj3IWFxbVYC&pg=PA299&. 
  9. ^ For example, Advanced Semiconductor Inc. (North Hollywood, California, USA) is selling Si point contact detectors which will cover from UHF (ultra high frequency) to 16 GHz.

External links

Patents

  • U.S. Patent 836,531 - Means for receiving intelligence communicated by electric waves (silicon detector), Greenleaf Whittier Pickard, 1906
  • U.S. Patent 837,616 - Wireless telegraph system (silicon carbide detector), Henry H.C. Dunwoody, 1906
  • U.S. Patent 906,991 - Oscillation detector (multiple metallic sulfide detectors), Clifford D. Babcock, 1908
  • U.S. Patent 912,613 - Oscillation detector and rectifier ("plated" silicon carbide detector with DC bias), G.W. Pickard, 1909
  • U.S. Patent 912,726 - Oscillation receiver (fractured surface red zinc oxide (zincite) detector), G.W. Pickard, 1909
  • U.S. Patent 933,263 - Oscillation device (iron pyrite detector), G.W. Pickard, 1909
  • U.S. Patent 1,118,228 - Oscillation detectors (paired dissimilar minerals), G.W. Pickard, 1914

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • cat's whisker — /kæts ˈwɪskə/ (say kats wiskuh) noun 1. Radio the wire forming one contact of the crystal in a crystal detector. 2. Colloquial a small amount, often of distance: she won the race by a cat s whisker. 3. (plural) → facebow. 4. the cat s whiskers,… …   Australian English dictionary

  • cat's-whisker — cat s whiskˈer noun (radio) A delicate wire brought into contact with a crystal to rectify the current in some forms of crystal detector and produce audibility • • • Main Entry: ↑cat …   Useful english dictionary

  • Detector (radio) — Passband modulation v · d · e Analog modulation AM · …   Wikipedia

  • cat whisker — noun or cat s whisker : a fine wire making contact with the crystal in the crystal detector or mixer of certain types of radio or electronic circuits * * * 1. Radio. a stiff wire forming one contact in a crystal detector and used for probing the… …   Useful english dictionary

  • cat whisker — 1. Radio. a stiff wire forming one contact in a crystal detector and used for probing the crystal. 2. Electronics. any wire for making contact with a semiconductor. Also, cat s whisker. Also called whisker. [1910 15] * * * …   Universalium

  • crystal detector — noun a detector consisting of a fine wire in contact with a galena crystal; acts as a rectifier • Hypernyms: ↑detector • Part Meronyms: ↑crystal * * * noun radio : a detector that depends for its operation on the rectifying action of the surface… …   Useful english dictionary

  • crystal detector — Radio. a device for rectifying a modulated radio frequency signal, consisting of a crystal of germanium, silicon, galena, or the like with a cat whisker contact, permitting a high frequency current to pass freely in one direction only: one of the …   Universalium

  • Crystal radio — Crystal set redirects here. For the Australian rock band, see The Crystal Set. A modern reproduction of an antique crystal set. It is tuned to different stations by moving the sliding contact (right) up and down the tuning coil (red). The device… …   Wikipedia

  • Audion tube — Audion redirects here. For other uses, see Audion (disambiguation). Triode Audion from 1908. (The 1906 Audion was a 2 element device with the signal applied to a wire wrapped around the glass envelope.) The Audion is an electronic amplifying… …   Wikipedia

  • Valve amplifier — A valve amplifier or tube amplifier is a type of electronic amplifier that make use of vacuum tubes instead of solid state semiconductor devices (such as transistors). As any other electronic amplifier they serve to increase the power and/or… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.