Steam locomotive condensing apparatus

Steam locomotive condensing apparatus

A steam locomotive condensing apparatus differs in purpose from the usual closed cycle steam engine condenser, in that its function is primarily either to recover water, or to avoid excessive emissions to the atmosphere, rather than maintaining a vacuum to improve both efficiency and power. It takes the form of a series of pipes, valves and other ancillary equipment usually attached to an otherwise conventional steam locomotive. The apparatus takes the exhaust steam that would normally be lost up the funnel and routes it through a heat exchanger, into the normal water tanks. Installations vary depending on the purpose, design and the type of locomotive to which it is fitted.

Contents

Purpose

Unlike the surface condenser often used on a steam turbine, the condensing apparatus on a steam locomotive does not normally increase the power output. In fact it may reduce it considerably. Whilst more power is potentially available by expanding down to a vacuum, the corresponding low density (high specific volume) implies extremely bulky low pressure cylinders or a turbine would be needed to actually extract it. So with a more practical volume ratio the condenser pressure would be near atmospheric rather than at a more typical low pressure, and the temperature would be correspondingly higher. In exhausting hot steam to the condenser, the temperature gradient between the exhaust steam and the cooling water is greater, so that a smaller heat exchange surface area is needed than would be required for typical stationary or ship-based steam plant of similar power. However none of the energy in the hot steam is available to do mechanical work. The potential improvement in thermal efficiency expected from including the condenser in the cycle is therefore not usually realised within the space constraints of a typical locomotive, indeed losses due to viscous friction in the condenser piping is likely to reduce the power output over what was achievable from simply venting to atmosphere. There are two usual reasons for fitting such equipment, reducing exhaust emissions and increasing range.

Reduced exhaust emissions

Underground railways

Mersey Railway locomotive, showing the prominent exhaust pipes leading back to the water tanks

Originally developed for the Metropolitan Railway to allow their locomotives to work the tunnels of the London Underground. This system was devised by Daniel Gooch and developed by Beyer Peacock. Steam is diverted from the exhaust steam pipes into the water tanks via condensing pipes within the same tanks. The water in the tanks could quickly heat up near boiling point, reducing the condensing effect on the exhaust steam. It was not unknown for the tanks to be emptied and refilled with cold water on a regular basis. Ordinary injectors will not work with hot water (until hot-water injectors were developed) so condensing locomotives were usually fitted with axle-driven boiler feedwater pumps. When not working in tunnels, the steam was directed to the blast pipe and up the funnel in the usual way.

Roadside tramways

In Britain, locomotives working on roadside steam tramways were required by law to have condensers. Water tank condensers (as above) were sometimes used but air-condensers were more common. A steam tram engine usually had a full-length roof and this was surmounted by a nest of air-cooled copper tubes in which the exhaust steam was condensed. Kitson & Co. made many engines of this type. The system was satisfactory for tram engines (which were very low-powered) but would not have worked for larger railway locomotives.

Increased range

Generally this was a more sophisticated installation that used forced air cooling to condense the exhaust steam. The system was intended to reduce the problems of getting enough water to steam locomotives running through desert and very arid areas.

Locomotives fitted with a condensing apparatus

See also

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Steam locomotive — A steam locomotive is a locomotive powered by steam. The term usually refers to its use on railways, but can also refer to a road locomotive such as a traction engine or steamroller.Steam locomotives dominated rail traction from the mid 19th… …   Wikipedia

  • Condensing — may refer to: Condensation Steam locomotive condensing apparatus Condensing boiler Condensing osteitis This disambiguation page lists articles associated with the same title. If an …   Wikipedia

  • Steam engine — A steam engine is a heat engine that performs mechanical work using steam as its working fluid. [ [http://www.britannica.com/EBchecked/topic/564472/steam engine steam engine Britannica Online Encyclopedia ] ] Steam engines have a long history,… …   Wikipedia

  • steam engine — steam engine, adj. an engine worked by steam, typically one in which a sliding piston in a cylinder is moved by the expansive action of the steam generated in a boiler. [1745 55] * * * Machine that uses steam power to perform mechanical work… …   Universalium

  • Condenser (steam engine) — Articles on Condenser (steam engine) include: Jet condenser Steam locomotive condensing apparatus Surface condenser This disambiguation page lists articles associated with the same title. If an inter …   Wikipedia

  • History of the steam engine — This article primarily deals with the history of the reciprocating type steam engine. The parallel development of turbine type engines is described in the steam turbine article. The history of the steam engine stretches back as far as the first… …   Wikipedia

  • Thomas Green & Son — Thomas Green Son, Ltd. were engineers who manufactured a wide range of products at the Smithfield Foundry, Leeds, United Kingdom. Introduction Thomas Green came to Leeds from Carlton on Trent near Newark and founded the company in 1835. The… …   Wikipedia

  • Surface condenser — A surface condenser is a commonly used term for a water cooled shell and tube heat exchanger installed on the exhaust steam from a steam turbine in thermal power stations.[1][2][3] These condensers are heat exchangers which convert steam from its …   Wikipedia

  • Condenser — may refer to: Condenser (heat transfer), a device or unit used to condense vapor into liquid. More specific articles on some types include: Air coil used in HVAC refrigeration systems Condenser (laboratory), a range of laboratory glassware used… …   Wikipedia

  • GNR Class N2 — Infobox Locomotive powertype=Steam name = GNR Class N2 LNER Class N2 caption = designer = Nigel Gresley builder = builddate = 1920 1929 totalproduction = whytetype = 0 6 2T gauge = standard gauge leadingsize = driversize = 5 8 length = weight =… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”