Flashback arrestor

Flashback arrestor

A flashback arrestor or flame arrestor is a device most commonly used in oxy-fuel welding and cutting to stop the flame from burning back up into the equipment and causing damage or explosions. The two main types are dry and wet. Each has its own advantages and disadvantages. Most oxy-fuel flashback arrestors are the dry type.

__TOC__

Dry flashback arrestor

Dry flashback arrestors typically use a combination of methods to stop flashback. This is the type that is typically found on most workshops, home or portable oxy-fuel kits as they work just as effectively with any orientation, need very little maintenance, and are often small and light enough to be installed between the torch and hoses. They include:
*Flame trap to cool the flame front. They are designed to allow free flow of gas through them but to take the heat out of the flame front to get it below the ignition temperature of the burning gas mixture. The most common types are:
**Sintered metal or ceramic.
**Layers of mesh.
**Ceramic beads.
*Temperature-triggered valves to stop the gas flow completely. Because it relies on extracting heat from the flashback to stop it continuing, most arrestors have a temperature-controlled valve that will cut off the gas flow when the unit reaches around 90°C, until either the unit cools (if the unit is automatic) or the reset button is pressed (if the unit is manual).
*A check valve that closes due to the back pressure.

Wet flashback arrestor

Normally wet flashback arrestors work by bubbling the gas through a non-flammable and ideally non-gas-absorbing liquid, which is typically water in shop installations or a specialized non-flammable oil in industrial uses. They stop the flame by preventing it from reaching the submerged intake.

These devices are normally very effective at stopping flashbacks from reaching the manifolds or regulators or tanks. They have the disadvantages of only working in one orientation and tend to be much larger than dry type arrestors. This makes them mainly only suitable for large or fixed installations.

If the unit has a pressure release valve to prevent the unit from bursting under a severe flashback, the fluid level should be monitored to keep it always above the intake and not so high that the liquid could splash or overflow into the outlet.

External links

* [http://www.iigas.com/fba.htm Flash Back And Flame Arrestor] (with diagrams)
* [http://www.murexwelding.co.uk/mrxcont/gas/mrxgwsebig.htm Saffire 36ec Flashback Arrestor internals] (with cut-away image)


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • flashback arrestor — /ˈflæʃbæk ərɛstə/ (say flashbak uhrestuh) noun a device commonly used with an oxywelding torch, LPG cylinder, etc., to prevent oxygen and a fuel gas mixing within one hose and to quench any flame that burns back up the equipment so that it cannot …  

  • Flashback (disambiguation) — Flashback or flashbacks may refer to:Flashback (psychological phenomenon), in which a person vividly remembers a past experience In literature * Flashback (literary technique), employed in literature and dramatic media: an interjected scene that… …   Wikipedia

  • Flashback (welding) — Flashback is a dangerous situation occurring during the use of an acetylene torch. The flame burns backwards into the hose, causing a popping or squealing noise. It can cause an explosion in the hose that injures or kills the user. Using a lower… …   Wikipedia

  • Oxy-fuel welding and cutting — Oxyacetylene redirects here. For the song, see Cubanate. Side of metal, cut by oxygen propane cutting torch …   Wikipedia

  • Oxyhydrogen — Knallgas redirects here. For bacteria which oxidize hydrogen, see Knallgas bacteria. Nineteenth century electrolytic cell for producing oxyhydrogen. Oxyhydrogen is a mixture of hydrogen (H2) and oxygen (O2) gases, typically in a 2:1 molar ratio,… …   Wikipedia

  • Flame arrester — A flame arrester being tested …   Wikipedia

  • Explosimeter — An explosimeter is a device which is used to measure the amount of combustible gases present in a sample. The device operates on the principle of resistance proportional to heat a wire is heated, and a sample of the gas is introduced to the hot… …   Wikipedia

  • Detonation flame arrester — This Detonation Flame Arrester is being tested for an 8 inch piping system at Brooker Laboratory Testing Company to the USCG 33cfr154.1325 Standard …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”