- Hybrid automatic repeat-request
Hybrid ARQ (HARQ) is a variation of the
ARQerror control method. In standard ARQ, error-detection information (ED) bits are added to data to be transmitted (such as cyclic redundancy check, CRC). In Hybrid ARQ, forward error correction(FEC) bits are also added to the existing Error Detection (ED) bits (such as Reed-Solomon codeor Turbo code). As a result Hybrid ARQ performs better than ordinary ARQ in poor signal conditions, but in its simplest form this comes at the expense of significantly lower throughput in good signal conditions. There is typically a signal quality cross-over point below which simple Hybrid ARQ is better, and above which basic ARQ is better.
The simplest version of HARQ, Type I HARQ, adds both ED and FEC information to each message prior to transmission. When the coded data block is received, the receiver first decodes the error-correction code. If the channel quality is good enough, all transmission errors should be correctable, and the receiver can obtain the correct data block. If the channel quality is bad, and not all transmission errors can be corrected, the receiver will detect this situation using the error-detection code, then the received coded data block is discarded and a retransmission is requested by the receiver, similar to ARQ.
In a more sophisticated form, Type II HARQ, transmits only ED bits or only FEC information and ED bits on a given transmission, typically alternating on successive transmissions.
To understand the difference between Type I and Type II Hybrid ARQ, consider the size of ED and FEC added information: detection typically only adds a couple bytes to a message, which is only an incremental increase in length. FEC, on the other hand, can often double or triple the message length with error correction parities. In terms of throughput, standard ARQ typically expends a few percent of channel capacity for reliable protection against error, while FEC ordinarily expends half or more of all channel capacity for channel improvement.
In standard ARQ a transmission must be received error free on any given transmission for the error detection to pass. In Type II Hybrid ARQ, the first transmission contains only data and error detection (no different than standard ARQ). If received error free, it's done. If data is received in error, the second transmission will contain FEC parities and error detection. If received error free, it's done. If received in error, error correction can be attempted by combining the information received from both transmissions.
Only Type I Hybrid ARQ suffers the capacity loss in strong signal condition. Type II Hybrid does not, because FEC bits are only transmitted on subsequent retransmissions as needed. In strong signal Type II Hybrid ARQ performs with as good capacity as standard ARQ. In poor signal conditions Type II Hybrid ARQ performs with as good sensitivity as standard FEQ.
In practice, incorrectly received coded data blocks are often stored at the receiver rather than discarded, and when the retransmitted block is received, the two blocks are combined ("
chase combining"). This can increase the probability of successful decoding.
An example of incremental redundancy HARQ is
HSDPA: the data block is first coded with a punctured 1/3 Turbo code, then during each (re)transmission the coded block is usually punctured further (i.e. only a fraction of the coded bits are chosen) and sent. The punctuation pattern used during each (re)transmission is different, so different coded bits are sent at each time.
HARQ can be used in stop-and-wait mode or in selective repeat mode. Stop-and-wait is simpler, but waiting for the receiver's acknowledgment reduces efficiency. Thus multiple stop-and-wait HARQ processes are often done in parallel in practice: when one HARQ process is waiting for an acknowledgment, another process can use the channel to send some more data.
There are other forward error correction codes can be used in HARQ scheme besides Turbo code,eg. extended irregular repeat-accumulate (eIRA) code and Efficiently-Encodable Rate-Compatible (E2RC) code,both of which are Low Density Parity Check Code.
HARQ is used in
HSDPAand HSUPAwhich provides high speed data transmission on downlinkand uplinkrespectively for mobile phone networks such as UMTS, and in the IEEE 802.16-2005 standard for mobile broadband wireless access, also known as "mobile WiMAX".It also has been used in 3GPP Long Term Evolution.
HARQ is generally implemented in hardware, rather than in software. Fact|date=December 2007
* Soljanin E., Hybrid ARQ in Wireless Networks, presented at Wireless System Lab Seminar, Texas A&M University, April 2003, and DIMACS Workshop on Network Information Theory, March 2003.
* R.A.Comroe and D.J.Costello. "ARQ schemes for data transmission in mobile radio systems". IEEE J. Select. Areas Commun., 2:472-481, July 1984.
* G. Davida and S. Reddy. "Forward Error Correction with Decision Feedback", Information and Control, Vol 21, 1972.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Automatic repeat request — L Automatic Repeat reQuest (en français requête automatique de répétition) est une méthode de contrôle d erreur pour la transmission de données. Elle utilise des acquittements et des timeouts pour parvenir à une transmission efficace de l… … Wikipédia en Français
Automatic repeat-request — Automatic Repeat Query (ARQ) (or Automatic Repeat reQuest) is an error control method for data transmission which uses acknowledgments and timeouts to achieve reliable data transmission. An acknowledgment is a message sent by the receiver to the… … Wikipedia
Automatic Repeat reQuest — L’Automatic Repeat reQuest (en français requête automatique de répétition) est une méthode de contrôle d erreur pour la transmission de données. Elle utilise des acquittements et des timeouts pour parvenir à une transmission efficace de l… … Wikipédia en Français
Selective Repeat ARQ — is a specific instance of the Automatic Repeat reQuest (ARQ) Protocol. It may be utilized as a protocol for the delivery and acknowledgement of message units, or it may be utilized as a protocol for the delivery of subdivided message sub… … Wikipedia
Error detection and correction — In mathematics, computer science, telecommunication, and information theory, error detection and correction has great practical importance in maintaining data (information) integrity across noisy channels and less than reliable storage… … Wikipedia
High-Speed Downlink Packet Access — (HSDPA) is an enhanced 3G (third generation) mobile telephony communications protocol in the High Speed Packet Access (HSPA) family, also dubbed 3.5G, 3G+ or turbo 3G, which allows networks based on Universal Mobile Telecommunications System… … Wikipedia
Forward error correction — In telecommunication, information theory, and coding theory, forward error correction (FEC) or channel coding is a technique used for controlling errors in data transmission over unreliable or noisy communication channels. The central idea is… … Wikipedia
WiMAX — Worldwide Interoperability for Microwave Access Logo trademarked by the WiMAX Forum … Wikipedia
IEEE 802.16 — The IEEE 802.16 Working Group on Broadband Wireless Access Standards , which was established by IEEE Standards Board in 1999, aims to prepare formal specifications for the global deployment of broadband Wireless Metropolitan Area Networks. The… … Wikipedia
3.5G — High Speed Downlink Packet Access Générations et normes de téléphonie mobile 0G PTT MTS IMTS AMTS 0,5G Autotel/PALM ARP 1G NMT AMPS Hicap CDPD Mobitex DataTac TACS RC2000 C NETZ Comvik NTT … Wikipédia en Français