- Transistor models
Transistors are complicated devices. In order to ensure the reliable operation of circuits employing transistors, it is necessary to scientifically model the physical phenomena observed in their operation using transistor models. There exists a variety of different models that range in complexity and in purpose. Transistor models divide into two major groups: models for device design and models for circuit design.
Models for device design
The modern transistor has an internal structure that exploits complex physical mechanisms. Device design requires a detailed understanding of how device manufacturing processes such as
ion implantation, impurity diffusion, oxide growth, annealing, and etching affect device behavior. Process models simulate the manufacturing steps and provide a microscopic description of device "geometry" to the device simulator. By "geometry" is meant not only readily identified geometrical features such as whether the gate is planar or wrap-around, or whether the source and drain are raised or recessed (see Figure 1 for a memory device with some unusual modeling challenges related to charging the floating gate by an avalanche process), but also details inside the structure, such as the doping profiles after completion of device processing.With this information about what the device looks like, the device simulator models the physical processes taking place in the device to determine its electrical behavior in a variety of circumstances: DC current-voltage behavior, transient behavior (both large-signal and small-signal), dependence on device layout (long and narrow versus short and wide, or interdigitated versus rectangular, or isolated versus proximate to other devices). These simulations tell the device designer whether the device process will produce devices with the electrical behavior needed by the circuit designer, and is used to inform the process designer about any necessary process improvements. Once the process gets close to manufacture, the predicted device characteristics are compared with measurement on test devices to check that the process and device models are working adequately.
Although long ago the device behavior modeled in this way was very simple - mainly drift plus diffusion in simple geometries - today many more processes must be modeled at a microscopic level; for example, leakage currents in junctions and oxides, complex transport of carriers including
velocity saturationand ballistic transport, quantum mechanical effects, use of multiple materials (for example, Si-SiGe devices, and stacks of different dielectrics) and even the statistical effects due to the probabilistic nature of ion placement and carrier transport inside the device. Several times a year the technology changes and simulations have to be repeated. The models may require change to reflect new physical effects, or to provide greater accuracy. The maintenance and improvement of these models is a business in itself.
These models are very computer intensive, involving detailed spatial and temporal solutions of coupled partial differential equations on three-dimensional grids inside the device.cite book
author=Carlo Jacoboni, Paolo Lugli
title=The Monte Carlo Method for Semiconductor Device Simulation
url=http://books.google.com/books?id=3cWnyhKmACEC&pg=PP1&dq=isbn:3211821104&sig=TCFY-o_l5gLj8OblcwGgQeB4Xts] cite book
title=Analysis and Simulation of Semiconductor Devices
url=http://books.google.com/books?id=EE4HlRZTYi4C&pg=PA97&dq=isbn:3211818006&sig=19_iT2-C0gy8WdBIPcLc7gRAXw8#PPP1,M1] cite book
author=Tibor Grasser (Editor)
title=Advanced Device Modeling and Simulation (Int. J. High Speed Electron. and Systems)
url=http://books.google.com/books?id=HBkA3_pZMp4C&dq=%22MOSFET++simulation%22&as_brr=0] cite book
author=Kramer, Kevin M. and Hitchon, W. Nicholas G.
title=Semiconductor devices: a simulation approach
publisher=Prentice Hall PTR
location=Upper Saddle River, NJ
isbn=0-13-614330-X] cite book
author=Dragica Vasileska, Stephen Goodnick
publisher=Morgan & Claypool
url=http://books.google.com/books?id=DBPnzqy5Fd8C&printsec=frontcover&dq=%22gate+tunneling%22&as_brr=0#PPA83,M1] Such models are slow to run and provide detail not needed for circuit design. Therefore, faster transistor models oriented toward circuit parameters are used for circuit design.
Models for circuit design ("compact" models)
Transistor models are used for almost all modern
electronic designwork. Analog circuitsimulators such as SPICEuse models to predict the behavior of a design. Most design work is related to integrated circuit designs which have a very large tooling cost, primarily for the photomasks used to create the devices, and there is a large economic incentive to get the design working without any iterations. Complete and accurate models allow a large percentage of designs to work the first time.
Modern circuits are usually very complex. The performance of such circuits is difficult to predict without accurate computer models, including but not limited to models of the devices used. The device models include effects of transistor layout: width, length, interdigitation, proximity to other devices; transient and DC
current-voltage characteristics; parasitic device capacitance, resistance, and inductance; time delays; and temperature effects; to name a few items. cite book
author=Carlos Galup-Montoro, Mǻrcio C Schneider
title=Mosfet Modeling for Circuit Analysis And Design
Large-signal nonlinear models
Nonlinear, or large signal transistor models fall into three main types:cite book
title=Mosfet Modeling for VLSI Simulation: Theory And Practice
url=http://books.google.com/books?id=SkT2xOuvpuYC&dq=%22table+lookup+model%22&as_brr=0] cite book
title=Operational Modeling of the MOS Transistor
: These are models based upon device physics, based upon approximate modeling of physical phenomena within a transistor. Parameters within these models are based upon physical properties such as oxide thicknesses, substrate doping concentrations, carrier mobility, etc. In the past these models were used extensively, but the complexity of modern devices makes them inadequate for quantitative design. Nonetheless, they find a place in hand analysis (that is, at the conceptual stage of circuit design), for example, for simplified estimates of signal-swing limitations.
: This type of model is entirely based upon
curve fitting, using whatever functions and parameter values most adequately fit measured data to enable simulation of transistor operation. Unlike a physical model, the parameters in an empirical model need have no fundamental basis, and will depend on the fitting procedure used to find them. The fitting procedure is key to success of these models if they are to be used to extrapolate to designs lying outside the range of data to which the models were originally fitted. Such extrapolation is a hope of such models, but is not fully realized so far.
: The third type of model is a form of
look-up tablecontaining a large number of values for common device parameters such as drain current and device parasitics. These values are indexed in reference to their corresponding bias voltage combinations. Thus, model accuracy is increased by inclusion of additional data points within the table. The chief advantage of this type of model is decreased simulation time (see article look-up tablefor discussion of the computational advantages of look-up tables). A limitation of these models is that they work best for designs that use devices within the table ( interpolation) and are unreliable for devices outside the table ( extrapolation).
The use of nonlinear models, which describe the entire operating area of a transistor, is required for digital designs, for circuits that operate in a large-signal regime such as
power amplifiers and mixers, and for the large-signal simulation of any circuit, for example, for stability or distortion analysis. Nonlinear models are used with a computer simulation program, such as SPICE. The models in SPICE are a hybrid of physical and empirical models, and such models are incomplete unless they include specification of how parameter values are to be extracted, especially as "unrealistic" (that is, unphysical) values can be made to fit the measured data without such a prescription. An incorrect set of fitting parameters results in wild predictions for devices that were not part of the originally fitted data set.
Large-signal computer models for devices continually evolve to keep up with changes in technology. To attempt standardization of model parameters used in different simulators, an industry working group was formed, the
Compact Model Council, to choose, maintain and promote the use of [http://www.geia.org/index.asp?bid=1333 standard models] . An elusive goal in such modeling is prediction of how circuits using the next generation of devices should work, to identify before the next step which direction the technology should take, and have models ready beforehand.
mall-signal linear models
Small-signal or linear models are used to evaluate stability,
gain, noise and bandwidth, both in the conceptual stages of circuit design (to decide between alternative design ideas before computer simulation is warranted) and using computers. A small-signal model is generated by taking derivatives of the current-voltage curves about a bias point or Q-point. As long as the signal is small relative to the nonlinearity of the device, the derivatives do not vary significantly, and can be treated as standard linear circuit elements. A big advantage of small signal models is they can be solved directly, while large signal nonlinear models are generally solved iteratively, with possible convergence or stability issues. By simplification to a linear model, the whole apparatus for solving linear equations becomes available, for example, simultaneous equations, determinants, and matrix theory(often studied as part of linear algebra), especially Cramer's rule. Another advantage is that a linear model is easier to think about, and helps to organize thought.
A transistor’s parameters represent its electrical properties. Engineers employ transistor parameters in production-line testing and in circuit design. A group of a transistor’s parameters sufficient to predict circuit
gain, input impedance, and output impedance are components in its small-signal model.
Parameters used in small-signal circuits (two ports) adopt names related to the names of these circuits such as
*Transmission parameters (T-parameters),
*Impedance parameters (z-parameters),
*Admittance parameters (y-parameters), and
*Scattering parameters (S-parameters).
These parameters all can be evaluated using measured scattering parameter data. Scattering parameters, or S parameters, can be measured for a transistor at a given bias point with a vector network analyzer.
* Ebers–Moll model
* [http://www-device.eecs.berkeley.edu/~bsim3 BSIM3] (see
* [http://www-device.eecs.berkeley.edu/~bsim3/bsim4.html BSIM4]
* [http://www-device.eecs.berkeley.edu/~bsimsoi BSIMSOI]
EKV MOSFET Model( [http://legwww.epfl.ch/ekv/ its web site at EPFL] )
* [http://pspmodel.asu.edu/ PSP]
* [http://www.iee.et.tu-dresden.de/iee/eb/hic_new/hic_start.html HICUM]
* [http://mextram.ewi.tudelft.nl/ MEXTRAM] .
* H-parameter model
*"Agilent EEsof EDA, IC-CAP Parameter Extraction and Device Modeling Software http://eesof.tm.agilent.com/products/iccap_main.html
Bipolar junction transistor#Theory and modeling
Safe operating area
Electronic design automation
Electronic circuit simulation
Semiconductor device modeling
Wikimedia Foundation. 2010.
Look at other dictionaries:
Transistor — For other uses, see Transistor (disambiguation). Assorted discrete transistors. Packages in order from top to bottom: TO 3, TO 126, TO 92, SOT 23 A transistor is a semiconductor device used to amplify and switch electronic signals and power. It… … Wikipedia
Transistor radio — This article is about an electronic device. For the fourth studio album by M. Ward, see Transistor Radio.A transistor radio is a small transistor based radio receiver. Historically, the term transistor radio refers to a radio that is monaural and … Wikipedia
Bipolar junction transistor — BJT redirects here. For the Japanese language proficiency test, see Business Japanese Proficiency Test. PNP … Wikipedia
Avalanche transistor — An Avalanche Transistor is a bipolar junction transistor designed for operation in the region of its collector current/collector to emitter voltage characteristics beyond the collector to emitter breakdown voltage, called avalanche breakdown… … Wikipedia
Thin film transistor liquid crystal display — A thin film transistor liquid crystal display (TFT LCD) is a variant of liquid crystal display (LCD) which uses thin film transistor (TFT) technology to improve image quality (e.g. addressability, contrast). TFT LCD is one type of active matrix… … Wikipedia
History of the transistor — Invention of the transistor= The first patent [patent|US|1745175|Julius Edgar Lilienfeld: Method and apparatus for controlling electric current first filed in Canada on 22.10.1925, describing a device similar to a MESFET] for the field effect… … Wikipedia
Organic field-effect transistor — OFET based flexible display An organic field effect transistor (OFET) is a field effect transistor using an organic semiconductor in its channel. OFETs can be prepared either by vacuum evaporation of small molecules, by solution casting of… … Wikipedia
Insulated-gate bipolar transistor — The insulated gate bipolar transistor or IGBT is a three terminal power semiconductor device, noted for high efficiency and fast switching. It switches electric power in many modern appliances: electric cars, variable speed refrigerators, air… … Wikipedia
Molecular models of DNA — While this purified DNA precipitated in a water jug (left) appears to be a formless mass, nucleic acids actually possess intricate structure at the nanoscale (right). M … Wikipedia
Sumlock ANITA calculator — The ANITA Mark VII and ANITA Mark VIII calculators were launched simultaneously in late 1961 as the world s first all electronic desktop calculators. Designed and built by the Bell Punch Co. in Britain, and marketed through its Sumlock… … Wikipedia