The crankset (in the US) or chainset (in the UK), is the component of a bicycle drivetrain that converts the reciprocating motion of the rider's legs into rotational motion used to drive the chain, which in turn drives the rear wheel. It consists of one or more sprockets, also called chainrings or chainwheels attached to the cranks, arms, or crankarms to which the pedals attach. It is connected to the rider by the pedals, to the bicycle frame by the bottom bracket, and to the rear sprocket, cassette or freewheel via the chain.
- 1 Parts
- 2 Variations
- 3 See also
- 4 References
The two cranks, one on each side and usually mounted 180° out of phase, connect the bottom bracket axle to the pedals.
Bicycle cranks can vary in length to accommodate different sized riders and different types of cycling. Crank length is measured from the center of the pedal spindle to the center of the bottom bracket spindle or axle. The larger bicycle component manufacturers typically offer crank lengths for adult riders from 165 mm to 180 mm long in 2.5 mm increments, with 170 mm cranks being the most common size. A few small specialty manufacturers make bicycle cranks in a number of sizes smaller than 165 mm and longer than 180 mm. Some manufacturers also make bicycle cranks that can be adjusted to different lengths. While logic would suggest that, all other things being equal, riders with shorter legs should use proportionally shorter cranks and those with longer legs should use proportionally longer cranks, this is not universally accepted. However, very few scientific studies have definitively examined the effect of crank length on sustained cycling performance and the studies' results have been mixed. Bicycle crank length has not been easy to study scientifically for a number reasons, chief among them is that cyclists are able to physiologically adapt to different crank lengths. Cyclists are typically more efficient pedalling cranks with which they have had an adaptation period. Several different formulas exist to calculate appropriate crank length for various riders. In addition to the rider's size, another factor affecting the selection of crank length is the rider's cycling specialty and the type of cycling event. Historically, bicycle riders have typically chosen proportionally shorter cranks for higher cadence cycling such as criterium and track racing, while riders have chosen proportionally longer cranks for lower cadence cycling such as time trial racing and mountain biking. However, the evolution of very low rider torso positions to reduce aerodynamic drag for time trial racing and triathlon cycling can also affect crank selection for such events. Some have suggested that proportionally shorter cranks may have a slight advantage for a rider with a very low torso position and an actute hip angle, especially as the rider pedals near the top-dead-center position of the pedal stroke.
Cranks are constructed of either an aluminum alloy, titanium, carbon fiber, chromoly steel, or some less expensive steel. Tubular steel cranks (such as Tioga's Revolver) can be light and very strong, are usually found on bmx bikes, and are slowly finding their way to mountain bikes (Dirt jumping and Urban assault) . Aluminum cranks may be cast, hot forged or cold forged ("cold" in this context means the billet from which the crank is to be made is heated to a specified temperature well below the melting point, not room temperature). Cold forging gives the metal additional strength, and the cranks can therefore be made lighter without increasing the risk of breakage. Shimano "Hollowtech" aluminum cranks are made by forging the main arms around a hard steel insert which is then withdrawn, leaving an internal void to save weight. They are then welded up before final machining.
There are a variety of methods used to attach the cranks to the bottom bracket spindle (or axle).
- Older cranks use a wedge-shaped pin, called a cotter, for attachment to the bottom bracket spindle.
- Newer cranks slide onto
- a square tapered spindle. The taper is 2 degrees with respect to the centerline. There are at least two non-interchangeable dimensions (e.g. Shimano and Campagnolo use competing standards in square taper, viz. JIS and ISO respectively, where the ISO spindle is longer and its taper end is slightly smaller. Most parts made by European manufacturers are to the ISO standard, and most Asian manufacturers use the JIS (Shimano) standard), and two orientations: diamond and square.
- a hexagonal tapered spindle (Tune components cranks are an example)
- a splined bottom bracket spindle with two prominent specifications, and numerous uncommon ones. The ISIS spline may be the most common splined standard as it was decided on and supported by several companies. Shimano's Octalink is a common proprietary standard that comes in two forms: version one for XTR, 105, Ultegra and Dura Ace; and version two for every other groupset such as XT, LX and Deore. Truvative and DMR also have their own proprietary spline interface standards. A 48 splined spindle, such as from Profile Racing, Demolition, and Eighth Inch, is mostly used for BMX, unicycles, and fixed-gear Freestyle.
- The cranks are pressed into place and prevented from squirming off via fretting by a bolt or nut installed into or onto the bottom bracket spindle. The head of the bolt or the nut sit inside a counterbore that is also threaded to accept a crank puller tool. The counterbore is often covered with a dust cover.
One solution to the issue of fretting is to use a metal based anti-seize lubricant between the mating parts. Composed of assorted mixtures of aluminum, copper, graphite and nickel powders in a grease base, such lubrication allows repeated assembly and dis-assembly without wear and the elimination of fretting corrosion during use.
- Even newer designs have the bottom bracket spindle, usually hollow and larger diameter than is possible for bottom brackets with bearings held inside the bottom bracket shell of a bike frame, for reduced weight and increased stiffness, permanently attached to the right crank (Shimano and others) or the left crank (Race Face). The left crank slides onto a spline and is tightened with one or more pinch bolts (Shimano) or is pressed onto a spline by a bolt on the bottom bracket spindle (Race Face).
- The latest from Campagnolo, called Ultra-TorqueTM, has each crank permanently attached to one half of the spindle (called semi-axles) which then join in the middle of the bottom bracket with a Hirth joint and a bolt.
- Certain companies such as Cannondale (BB30 open standard, introduced in 2000) have made their own unique bottom bracket standards requiring changes in the bottom bracket shell of the bicycle frame in order to accommodate the bottom bracket/crank design. The open BB30 standard is gaining popularity on high end bicycle and component manufacturers (Zipp, Specialized, FSA).
- Finally, many children's bikes and older, or less-expensive bikes have one-piece ("Ashtabula") cranks where the two cranks and bottom bracket spindle are forged as one piece of steel (see photograph above).
See the bottom bracket article for more details.
To the pedals
Crank arms have a threaded hole (or "eye") at their outboard end to accommodate the pedal spindle. Adult or multi-piece cranks have a 9/16 inch hole with 20 TPI (a combination that appears to be unique to this application). One-piece or children's cranks use a 1/2 inch hole. Some cranks on children's bikes have more than one pedal hole so that the pedal can be moved to accommodate growth.
The right-side (usually the chain side) hole is right-hand threaded, and the left-side hole is left-hand (reverse) threaded to help prevent it from becoming unthreaded by an effect called precession.
Pedal spindles are hard steel, and gradually fret and erode the crankarm where the two meet. This can eventually be a cause of crank breakage, which commonly occurs at the pedal eye. Some manufacturers advise the use of a thin steel washer between the pedal and crank, but this is ineffective because the hard washer frets against the crank instead. A solution, suggested by Jobst Brandt, is to use a 45 degree taper at the surface where crank and pedal meet, as this would eliminate precession-induced fretting and loosening (it is already done for most automobile lug nuts for the latter reason). However, this would require manufacturers to change a well-established standard which currently allows most pedals to be fitted to most cranks.
The solution[dubious ] to the issue of fretting is to use a metal based anti-seize lubricant; being composed of assorted mixtures of aluminium, copper, graphite and nickel powders in a grease base - that allows repeated assembly and disassembly without wear and the elimination of fretting corrosion during use.
On older styles, the spider—the multi-armed piece that connects the chainring to the bottom bracket axle—was a separate piece from the crank arm. The most common modern cranks have an integrated spider on the drive-side crank arm. However, Middleburn, TA, and Surly currently produce cranks with separate detachable spiders, enabling a wide variety of chainring patterns to be used with the same cranks.
Spiders usually have 4 or 5 arms, although some models have had as few as 3 and many as 10 arms with 6 having been popular in the past.
Bolt circle diameter (BCD)
Many modern bicycles have removable chainrings, to allow for replacement when worn, or to change the gear ratio provided (although the change is limited).
The holes on the spider arms used for attaching a chainring can have a variety of dimensions, referred to as the bolt circle diameter, commonly abbreviated as BCD. This measurement is sometimes referred to as pitch-circle diameter (PCD). Cranks designed to mount one or two chainrings will almost always use a single bolt circle diameter. Cranks designed to mount three chainrings will almost always use two different bolt circle diameters; the larger to mount the two outer rings and the smaller to mount the inner ring. Most modern two-chainring cranks use either a 110mm or 130mm bolt circle diameter.
Bolt circle diameters of common cranks:
- 130, 135, or 144 BCD
- Road double
- 130 BCD (Shimano and others), or 135 (Campagnolo)
- Road triple
- 130/74 BCD (Shimano and others), or 135/74 BCD (Campagnolo)
- Compact/touring double
- 110 BCD or (Campagnolo carbon 4×110/1×113 BCD)
- Compact/touring triple
- 110/74 BCD
- Mountain bike (4 arm)
- 104/64 BCD
- Mountain bike (5 arm standard)
- 110/74 BCD
- Mountain bike (5 arm compact)
- 94/58 BCD
Chainrings (also called "chain rings", "chainwheels" or "sprockets", although sprocket is used this way mostly in the BMX community) engage the chain to transfer power to the (usually rear) wheel. They usually have teeth spaced to engage every link of the chain as it passes over; however, in the past, some designs (called skip-tooth or inch-pitch) have had one tooth for every other link of the chain.
By convention, the largest chainring is outboard and the smallest is inboard. Chainrings vary in size from as few as 20 teeth to as many as 55 or potentially more.
Chainrings also come in several nominal widths:
- 3/16" (4.76 mm) for old-time bikes (especially skip-tooth or inch-pitch), heavy duty BMX, Worksman, and exercise bikes
- 1/8" (3.18 mm) for track, BMX, cruiser bikes, one-speed, three-speeds, and the rare derailleur bike.
- 3/32" (2.38 mm) for road, hybrid, mtb bikes, single-speed and 5-, 6-, 7-speed freewheels.
- 5/64" (1.98 mm) for any bike with 9- or 10-speed cassettes
Chainrings are constructed of either an aluminum alloy, titanium, steel, or carbon fiber.
Cheaper cranksets may have the chainrings welded or riveted directly to the crank arm or spider. More expensive sets have the chainrings bolted on so that they can be replaced if worn or damaged, or to provide different gearing.
Replacement chainrings must be chosen with a bolt-hole count and spacing that matches the spider.
Chainrings designed for use with multi-chainring crank arms may have ramps or pins to aid in shifting. The middle chain ring, in the case of a triple crankset, usually has the most shaping to aid in shifting up and down. The smallest chainring usually has the least, if any shaping.
On tandem bicycles the pedalling contribution of both riders is often combined and coordinated by the crank arms. There may be a second set of chain rings, often on the opposite side from the regular drive train, one on each crank set and connected by a separate chain. The most common implementation has both cyclists pedaling at exactly the same pace and usually in phase, although it is possible to configure the system for out-of-phase pedaling.
The most common tandem crankset is a set of four cranks. Both left cranks have spiders and chainrings to be connected by a timing chain, and only one of the right cranks has a spider for the drive chain.
There are tandem cranksets available called independent pedaling system cranksets, which allow each cyclist to pedal, or not, at their own pace.
Some cranksets incorporate a chain guard that consists simply of a plastic or metal ring outboard of the largest chainring and slightly larger in diameter to help prevent the chain from touching or catching clothing. Bicycles that are going to be used in abusive applications, such as freeride and BMX, will often incorporate a very heavy-duty chain guard that is designed to protect the chainrings from physical damage caused by impact with fixed objects; also called 'bashguards', these commonly replace a third (large) chainring.
Some cranksets used for freeride and downhill mountain biking have a chainguide installed. A chainguide is a metal or plastic housing that keeps the chain on the chainrings over rough terrain and during technical riding. Most chainguides are designed for only one front chainring, but there are a few dual-ring chainguides available such as the E13 DRS and MRP LRP. Chainguides include a channel on the top of the chainring to keep the chain in line (for models designed for one front chainring) and a roller or sprocket on the bottom to help keep the chain engaged with the chainring. These are almost always used in conjunction with bashguards. Exceptions including the E.thirteen LG-1 and the MRP G2 (and now the G2 SL) do exist which use integrated skid plates, removing impact forces from the crank's spider and transferring them to the frame.
Some cranksets have been produced that incorporate a ratcheting mechanism to accommodate coasting. In this case, the chain continues to rotate with the rear wheel when the rider stops pedaling. The ultimate goal of freewheeling cranks is to allow the rider to shift the chain while coasting. Shimano's discontinued FF system (Front Freewheeling) is one of the more commonly seen examples.
This configuration consists of a left crank arm with a spider and chainring, and a right crank arm without a spider. This is exactly the opposite of a normal configuration. The special crankset must also be paired with a rear hub that can be driven from the left side. These hubs typically have left hand threads for a special freewheel, which is also threaded left hand and ratchets the opposite direction of a normal freewheel. If the freewheel and hub were threaded with right hand threads, the torque applied by pedaling would loosen and unthread the freewheel from the hub.
Left-side-drive is sometimes done with a fixed gear drivetrain. Because a correctly installed track cog can not be loosened from the hub no matter which way torque is applied, it can be used for left-side drive without requiring special left hand threaded parts.
Note that a normal right-side-drive crankset can not be installed backwards to create a left-side-drive bicycle because the threaded pedal holes at the end of the crank arms would be backwards of normal. Even though some kinds of pedals could simply be installed on the wrong sides to get around this issue, precession would tend to loosen them over time, causing the pedals to become detached and/or damaging the pedal threading in the crank arms. A front crankset designed for tandem use is a commercially available option, since this has a chainring for the timing chain on the left side. Choice of chainring sizes may be limited.
Independent crank arms
At least one manufacturer offers a crankset in which the crank arms may rotate independently. This is supposed to aid in training by requiring each leg to move its own pedal in a full circle. One independent study has demonstrated training with these cranks can improve cycling efficiency. The manufacture also claims that this change can also be useful to aid in running improvement, help prevent injuries in runners, improve core strength development, and are useful for the rehabilitation of lower extremity injuries, especially in the athlete. The manufacturer claims these cranks have been used as a training tool by several World and Olympic Champions in both cycling and triathlon and several professional sports teams including MLB and NFL teams, and other uses.
Non Round chainrings
Several manufacturers have tried non-round chainrings, such as Shimano's Biopace, Rotor's Q-Rings and Osymetric's Harmonic ring. These are designed to provide varying mechanical advantage at different points in the pedal stroke, effectively changing the gear ratio at different angles of rotation with the intention to be more ergonomic. Non-round chainrings can sometimes cause problems in front shifting.
Their significant popularity in the late eighties to early nineties is best reflected in their widespread use by professional cyclists of that time. However, one hold-out has been Team CSC Saxo Bank veteran Bobby Julich, and there are still a couple of pro riders that use them as late as 2011. Notably Bradley Wiggins of Team SKY, David Millar of Team Garmin Transitions and Agritubel's Geoffrey Lequatreall riding the Osymetric brand and Team CSC Saxo Bank's Carlos Sastre with Rotor's Q-Rings from his native Spain. Sastre won the 2008 Tour de France with Q-rings. Bradley Wiggins of the Garmin Slipstream team used an oval chainring from Osymetric in his TT bike (Felt DA) in the 2009 Tour de France. In the 2010 Giro D'Italia, and David Millar used them in his 2011 victory in the final TT of the 2011 Giro. Several Pro-Tour teams were using Osymetric and Q-Rings ovoid chainrings for road racing and time trialing.
In the context of mountain biking the term compact crankset, or micro drive, refers to smaller triple cranksets, giving a small benefit in weight at the expense of increased wear and also giving the bike better clearance over obstacles. Typical ratios would be 22/32/44 teeth as opposed to 28/38/48 or 24/36/46 teeth. These would be used with smaller cassettes (Generally cassettes are available with 11 tooth minimum gear sizes for compact chainsets while standard chainsets were designed for cassettes with a 13 or 14 tooth top gear), giving the same overall ratio. Compact chainrings are the dominant standard for mountain bike cranks for the past decade or so.
In the context of road cycling, compact drivetrain typically refers to double cranksets with a smaller (usually 110mm) bolt circle diameter than the standard 130mm or Campagnolo's 135mm. As of 2006, all of the major component manufacturers such as Shimano and Campagnolo offer compact cranks in their midrange and high-end product lines. The compact crankset provides a compromise between the standard road double crankset (with 39/52 or 39/53 tooth chainrings) and the road triple (with 30/42/52 or 30/39/53 tooth chainrings). The compact crankset has two chainrings and typical ratios are 34/48, 34/50 and 36/50. This provides nearly the same lower gear ratios as a triple but without the need for a third chainring, a triple front derailleur and a long cage rear derailleur. Both Shimano and Campagnolo recommend and sell front derailleurs specifically designed for compact cranksets, claiming better shifting.
Compact gearing is not necessarily lower than standard gearing if cassettes with smaller sprockets (such as 11–23) are used. A high gear of 50×11 on a compact drivechain is actually slightly higher than the 53×12 of a standard set.
Compact gearing usually has a large percentage jump between the two chainrings. In balance, it may also allow small jumps in the rear by allowing a closer ratio cassette to be used, except for the 9% jump at the high end between the 11 and 12 tooth sprockets.
Marketed and known by a variety of names (Z-cranks, P.M.P cranks, etc.) non-straight crank arms have been introduced several times. However, "as long as the distance from crank axle to pedal is fixed, there is no pedaling advantage in using bent crank arms". Possible disadvantages from comparable straight crank arms include more weight and more flex.
Rotor is a trade name of a type of crank used in the transmission system of a bicycle. Unlike a standard pair of cranks that always remain at 180 degrees relative to each other, the Rotor system varies this angle through the circle of motion. The manufacturer claims that by reducing the time each crank spends in the top and bottom "dead spots", where little or no force is available from the leg, power output relative to heart rate is increased, amongst other claimed benefits.
The Rotor crank was developed by Aeronautic Engineering School students in Madrid, Spain in 1995 and was later commercialised. While Rotor cranks have found success with town and cargo cyclists, many competitive cyclists continue to use the traditional fixed system as offered by major manufacturers Campagnolo and Shimano, amongst others. One major factor is weight—Rotor cranks are 50%–75% heavier than most competitive cranks. Another factor is that a cyclist with more than one bike needs to change them all to the Rotor system, which can be expensive, and adaptation to the Rotor pedaling style can take around a week [Source?]. Many competitive cyclists, including Cervélo TestTeam, use Rotor's Q-rings which provide many of the same benefits without the added weight.
A planetary-gear crankset offers two different gear ratios with just one chainring. This can have at least two advantages: shifting while not pedalling and fewer chances for the chain to come off the chainring. The Mountain Drive & Speed-Drive by Schlumpf Innovations and the Hammerschmidt are examples.
- ^ "Bike Works NYC Chainring Archive". http://www.bikecult.com/works/chainring.html. Retrieved 2007-10-21.
- ^ "Shimano Technical SG-X Chainrings". http://bike.shimano.com/publish/content/cycle/sac/us/en/technical_service/shimano_technology/front_shifting_technology.html. Retrieved 2007-10-21.
- ^ a b c Brown, Sheldon. "Sheldon Brown's Bicycle Glossary: Chainring". Sheldon Brown. http://www.sheldonbrown.com/gloss_ch.html. Retrieved 2007-10-21.
- ^ Brown, Sheldon. "Sheldon Brown's Bicycle Glossary: Crank". Sheldon Brown. http://www.sheldonbrown.com/gloss_cn-z.html#crank. Retrieved 2007-10-21. "Sometimes called a "crank arm", but this is redundant and inelegant. Call it a crank, or call it an arm, but please don't call it a "crank arm"."
- ^ Lennard Zinn (Jun 5th 2007). "Tech Report, with Lennard Zinn – The new Madone". VeloNews. http://velonews.competitor.com/2007/06/bikes-tech/tech-report-with-lennard-zinn-the-new-madone_12366. Retrieved 2010-07-12. "The only tool required is a hex key to tighten the headset top cap and to attach the left crankarm."
- ^ "Sheldon Brown: Square Taper Bottom Bracket Interchangeability". http://www.sheldonbrown.com/bbtaper.html. Retrieved 2008-08-28.
- ^ "Fretting damage in Bicycle Mechanics". http://www.sheldonbrown.com/brandt/fretting.html. Retrieved 2008-08-28.
- ^ "Campagnolo Ultra-Torque Crankset". 2006. http://www.campagnolo.com/ultratorque.php. Retrieved 2006-12-14.
- ^ "Bike Works NYC Chainring Archive". http://www.bikecult.com/works/chainring.html. Retrieved 2007-01-16.
- ^ Oxford English Dictionary. Oxford University Press. April 2010. "1991: Bicycle Guide Sept. 54/2, On a smooth graded downhill,...Herbold trades up to a 62-tooth chainring. 2006: Toro (Canada) Summer 110/3, A third inside chain ring (a.k.a. the granny gear)‥means you can stay in the saddle all the way to the top of gruelling steeps."
- ^ "Bike Works NYC Chainwheel Archive". 2006. http://www.bikecult.com/works/chainwheel.html. Retrieved 2006-12-14.
- ^ "IPS Independent Pedaling System" (PDF). 2001. http://www.hostelshoppe.com/atp_archives/ips_instructions.pdf. Retrieved 2006-12-14.
- ^ "PowerCranks". http://www.powercranks.com/. Retrieved 12-08-2009.
- ^ Luttrell. Effects of short-term training using powercranks on cardiovascular fitness and cycling efficiency. PMID 14666944.
- ^ "Comparative biomechanical study of circular and non-circular chainrings for endurance cycling at constant speed.". http://www.noncircularchainring.be/pdf/Biomechanical%20study%20chainrings%20-%20release%202.pdf. Retrieved 2010-08-27.
- ^ Stokes, Shane (2008-02-06). "Carlos Sastre's Cervélo TestTeam Cervélo S3". cyclingnews.com. Cyclingnews. http://autobus.cyclingnews.com/tech/2009/probikes/?id=carlos_sastre_cervelo_testeam_s3. Retrieved 2010-04-12.
- ^ Stokes, Shane (2009-02-03). "Pro bike: Carlos Sastre’s Cervélo TestTeam Cervélo S3". bikeradar.com. http://www.bikeradar.com/Road/news/article/pro-bike-carlos-sastres-cervlo-testteam-cervlo-s3-20229. Retrieved 2010-04-12. "One of the most striking components on the bike is the chainset. Sastre won the 2008 Tour de France using Rotor Q-Ring elliptical chainrings mounted on FSA crankarms and the entire team has gone all-Rotor for 2009, using the Q-Rings, a novel self-aligning bottom bracket and – officially - the Ágilis Evo crankset."
- ^ Cycling Weekly, Photos by Andy Jones (06-07-2009). "Bradley Wiggins' Tour de France time trial bike". IPC Media Ltd.. http://www.cyclingweekly.co.uk/news/latest/381426/bradley-wiggins-tour-de-france-time-trial-bike.html. Retrieved 2010-02-09.
- ^ "Bike Works NYC Chainring Archive: Bent Crank Arms". http://www.bikecult.com/works/chainring.html. Retrieved 2007-01-16.
- ^ "ROTOR: Fabricacion de Componentes para Bicicletas". RotorBike.com. 2008-10-17. http://www.rotorbike.com/index2.html.
- ^ "The world center of cycling". CyclingNews.com. 2008-10-17. http://autobus.cyclingnews.com/tech/?id=2002/reviews/rotor_cranks.
- ^ "New Cervélo TestTeam bikes for the cobbled Classics". bikeradar.com. 2009-04-04. http://www.bikeradar.com/road/news/article/new-cervlo-testteam-bikes-for-the-cobbled-classics-21113.
- ^ "Q-Rings General Information". http://www.rotorbikeusa.com/pdf/More%20information_Q%20Rings.pdf.
- ^ Davis, Alan. "Previewed: Unveiling Truvativ's Hammerschmidt". bikemagazine. http://www.bikemag.com/news/freshproduce/8-12-08-previewed-unveiling-truvativs-hammerschmidt/. Retrieved 12-08-2009.
- ^ "Schlumpf Innovations". http://www.schlumpf.ch/. Retrieved 2010-05-05.
- Barnett, John (2003). Barnett's Manual: Analysis and Procedures for Bicycle Mechanics (5th edition ed.). Boulder, CO: VeloPress. ISBN 1-931382-29-8.
List of bicycle parts Frame Wheels Drivetrain Cabling Peripherals
Wikimedia Foundation. 2010.
Look at other dictionaries:
Crankset — Pays d’origine France Genre(s) hardcore metal Années actives depuis 1997 Site Web … Wikipédia en Français
crankset — A group of components on a bicycle that includes the bottom bracket removable parts, two crankarms, and one or more chainrings. Also see cotterless crankset … Dictionary of automotive terms
CRANKSET Versus Noise Data — Album par Crankset Noise Data Sortie 2006 Enregistrement Le Metro (France) Genre(s) metal Producteur(s) Crankset Noise Data … Wikipédia en Français
cotterless crankset — A bicyclecrankset in which the crankarms are fastened to the axle by means of nuts or bolts instead of cotter pins … Dictionary of automotive terms
Bottom bracket — A square taper cartridge bottom bracket. The bottom bracket on a bicycle connects the crankset to the bicycle and allows the crankset to rotate freely. It contains a spindle that the crankset attaches to, and the bearings that allow the spindle… … Wikipedia
Tandem bicycle — The tandem bicycle or twin is a form of bicycle (occasionally, a tricycle) designed to be ridden by more than one person. The term tandem refers to the seating arrangement (fore to aft, not side by side) instead of the number of… … Wikipedia
Waiting After Rebellion — Album par Crankset Sortie 2004 Enregistrement Factory Studio (France) Durée 61:03 Genre(s) metal Producteur(s) … Wikipédia en Français
Bicycle gearing — The gearing on a bicycle is the selection of appropriate gear ratios for optimum efficiency or comfort. Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi speed bicycles allow gear selection to… … Wikipedia
Cycling power meter — A cycling power meter is a device on a bicycle that allows measuring of the power output of the rider. Most cycling power meters use strain gauges to measure torque applied, and, combined with angular velocity, calculate power. The Technology was … Wikipedia
Future For Thought — Album par Crankset Sortie 2001 Enregistrement Factory Studio (France) Durée 61:13 Genre(s) metal Producteur(s) … Wikipédia en Français