Chirped mirror

Chirped mirror
An electron microscope image of a tiny piece of dielectric mirror being cut out from a larger substrate. The periodic structure of the mirror is clearly visible on the bottom edge. In a chirped dielectric mirror the space between layers would not be all the same, but would become gradually wider to create the chirped effect. The distance between the layers determines the wavelength of light that is reflected by that layer, so the varying space between layers creates layers that reflect varying wavelengths of light.

A chirped mirror is a dielectric mirror with chirped spaces—spaces of varying depth designed to reflect varying wavelengths of lights—between the dielectric layers (stack).

Chirped mirrors are used in applications like lasers to reflect a wider range of light wavelengths than ordinary dielectric mirrors, or to compensate for the dispersion of wavelengths that can be created by some optical elements.

Contents

Simple explanation

An ordinary dielectric mirror is made to reflect a single frequency of light. The dielectric mirror is made of transparent materials that are uniformly layered at a depth of 1/4 the wavelength of light the dielectric mirror is designed to reflect. The dielectric mirror is transparent to other wavelengths of light except those in a very narrow band around the wavelength it is designed to reflect.

A chirped mirror is made to reflect a wider range of frequencies. This is done by creating layers with different depths. There may be 10 layers with a depth designed to reflect a certain wavelength of light, another 10 layers with slightly greater depth to reflect a slightly longer wavelength of light, and so on for the entire range of wavelengths of light the mirror is designed to reflect. The result is a mirror that can reflect a whole range of light wavelengths rather than single narrow band of wavelengths.

Because light reflected from the deeper layers of the mirror travels a longer distance than the light that reflects off the surface layers, a chirped mirror can be designed to change the relative times of wavefronts of different wavelength reflecting from it. This may be used, for example, to disperse a pulse of light of different wavelengths which arrives all at one time or to tighten a pulse of light where different wavelengths arrive dispersed in time.

This ability tighten or more tightly pack a pulse of light of different wavelengths is important, because some commonly used optical elements naturally disperse a packet of light according to wavelength, a phenomenon known as chromatic dispersion. A chirped mirror can be designed to compensate for the chromatic dispersion created by other optical elements in a system.

This is a simplified explanation which omits some important but more complex technical considerations.

Technical explanation

For dielectric mirrors, materials with a refractive index of 1.5 and 2.2 are available. The Fresnel reflection for the amplitude is about 0.2. So with 10 layers about 0.99 of the light amplitude that is 0.98 of the light intensity is reflected. Chirped mirrors use 60 layers. So the light of a specific frequency interacts only with one sixth of the whole stack.

The surface leads to an early reflection of a pulse with an unaltered chirp. This is prevented by sparing some layers for anti-reflective coating. In a simple case this is done with a single layer of MgF2, which has a refractive index of 1.38 (in the near infrared). The bandwidth is large, but not one octave. Going from normal incidence to Brewster's angle p-polarized is less and less reflected. To eliminate residual reflections from the surface in the case of multiple mirrors, the distance between the surface and the stack is different for every mirror.

Naively one would think that the chirp starts outside the desired wavelength range, and any wavelength within the range experiences a complete resonance fade in and fade out. A detailed calculation (references in the external link ) says that the reflectivity of the mirror must be chirped also by not allotting the λ/2 equally across high and low index of refraction material. These are called double chirped mirrors.

Application

In Ti-sapphire lasers which employ Kerr-lens modelocking, chirped mirrors are often used as the sole means to compensate group delay variations. Considering the above numbers a single mirror can compensate 4 µm optical path length. Considering the group velocity this is enough for the 3 m air inside the cavity, for the 3 mm of Ti:sapphire crystal three more mirrors are needed, so that a simple Z-cavity can already be compensated. On the other hand, the gain of the crystal of about 1.1 which is high enough to compensate the loss of 8 mirrors, which gives more degrees of freedom in group delay compensation. More critically for short pulses is that the frequency components outside the gain range of the crystal generated indirectly by self-phase modulation are not lost through the end or folding mirrors but and are transmitted through the out-couple mirror. In a kind of decision by majority the modes of the laser decide which group delay to choose, and spectral components close to this delay are emphasized in the output. Due to the ripples in the compensation, the spectrum also has ripples. A single stack reflects between 780 nm and 800 nm. The chirped mirror with 6 times the layers can be reflective from 730 nm to 850 nm. The gain of Ti:Sa is greater than one between 600 nm and 1200 nm. To reflect this bandwidth higher losses have to be accepted.

In Chirped pulse amplification these mirrors are used to correct residual variations of group delay after a grating compressor is inserted into the system.

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Chirped pulse amplification — Diagramatic scheme of chirped pulse amplification. Chirped pulse amplification (CPA) is a technique for amplifying an ultrashort laser pulse up to the petawatt level with the laser pulse being stretched out temporally and spectrally prior to… …   Wikipedia

  • Prism compressor — A prism compressor is an optical device used to shorten the duration of a positively chirped ultrashort laser pulse by giving different wavelength components a different time delay. It typically consists of two prisms and a mirror. Figure 1 shows …   Wikipedia

  • Chirp — For other uses, see Chirp (disambiguation). A chirp is a signal in which the frequency increases ( up chirp ) or decreases ( down chirp ) with time. In some sources, the term chirp is used interchangeably with sweep signal.[1] It is commonly used …   Wikipedia

  • Laser acronyms — Here, is a list of acronyms used in laser physics, applications and technology.A*AOM – acousto optic modulator *APD – avalanche photodiode *APM – additive pulse mode locking *ASE – amplified spontaneous emission *AWG – arrayed waveguide… …   Wikipedia

  • Kerr-lens modelocking — (KLM) is a method of modelocking lasers via a nonlinear optical process known as the optical Kerr effect . This method allows the generation of pulses of light with a duration as short as a few femtoseconds.The optical Kerr effect is a process… …   Wikipedia

  • Bragg-Reflektor — Bragg Reflektor,   Bragg Spiegel [bræg , nach W. L. Bragg], Schichtfolge nicht absorbierender dielektrischer Schichten mit abwechselnd hoher und niedriger Brechzahl. Sind die optischen Weglängen der beiden Schichten einander gleich, gilt also n1… …   Universal-Lexikon

  • Optics — For the book by Sir Isaac Newton, see Opticks. Optical redirects here. For the musical artist, see Optical (artist). Optics includes study of dispersion of light. Optics is the branch of …   Wikipedia

  • Fiber Bragg grating — A fiber Bragg grating (FBG) is a type of distributed Bragg reflector constructed in a short segment of optical fiber that reflects particular wavelengths of light and transmits all others. This is achieved by adding a periodic variation to the… …   Wikipedia

  • Nonlinear optics — (NLO) is the branch of optics that describes the behaviour of light in nonlinear media, that is, media in which the dielectric polarization P responds nonlinearly to the electric field E of the light. This nonlinearity is typically only observed… …   Wikipedia

  • Ti-sapphire laser — Ti:sapphire lasers (also known as Ti:Al2O3 lasers, titanium sapphire lasers, or simply Ti:sapphs) are tunable lasers which emit red and near infrared light in the range from 650 to 1100 nanometers. These lasers are mainly used in scientific… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”