- Nuclear poison
A nuclear poison, also called a neutron poison is a substance with a large neutron absorption cross-section in applications, such as
nuclear reactors, when absorbing neutrons is an undesirable effect. However neutron-absorbing materials, also called poisons, are intentionally inserted into some types of reactors in order to lower the high reactivity of their initial fresh fuel load. Some of these poisons deplete as they absorb neutrons during reactor operation, while others remain relatively constant.
Transient fission product poisons
Some of the
fission productsgenerated during a nuclear reactionhave a high neutron absorption capacity, such as xenon-135(Xe-135) and samarium-149 (Sm-149). Because these two fission product poisons remove neutrons from the reactor, they will have an impact on the thermal utilization factor and thus the reactivity. The poisoning of a reactor core by these fission products may become so serious that the chain reactioncomes to a standstill.
Xe-135 in particular has a tremendous impact on the operation of a nuclear reactor. The inability of a reactor to be started due to the effects of Xe-135 is sometimes referred to as "xenon precluded start-up". The period of time where the reactor is unable to override the effects of Xe-135 is called the "xenon dead time". During periods of steady state operation, at a constant
neutron fluxlevel, the Xe-135 concentration builds up to its equilibrium value for that reactor power in about 40 to 50 hours. When the reactor power is increased, Xe-135 concentration initially decreases because the burn up is increased at the new higher power level. Because 95% of the Xe-135 production is from iodine-135 decay, which has a 6 to 7 hour half-life, the production of Xe-135 remains constant, at this point, the Xe-135 concentration reaches a minimum. The concentration then increases to the new equilibrium level for the new power level in again roughly 40 to 50 hours. The magnitude and the rate of change of concentration during the initial 4 to 6 hours following the power change is dependent upon the initial power level and on the amount of change in power level; the Xe-135 concentration change is greater for a larger change in power level. When reactor power is decreased, the process is reversed. ["DOE Fundamentals Handbook: Nuclear Physics and Reactor Theory", pages 35-42.]
Because Sm-149 is not radioactive and is not removed by decay, it presents problems somewhat different from those encountered with Xe-135. The equilibrium concentration and (thus the poisoning effect) builds to an equilibrium value during reactor operation in about 500 hours, and since Sm-149 is stable, the concentration remains essentially constant during reactor operation. ["DOE Fundamentals Handbook: Nuclear Physics and Reactor Theory", pages 43-47.]
Accumulating fission product poisons
There are numerous other fission products that, as a result of their concentration and thermal neutron absorption cross section, have a poisoning effect on reactor operation. Individually, they are of little consequence, but taken together they have a significant impact. These are often characterized as "lumped fission product poisons" and accumulate at an average rate of 50 barns per fission event in the reactor. The buildup of fission product poisons in the fuel eventually leads to loss of efficiency, and in some cases to instability. In practice, buildup of reactor poisons in nuclear fuel is what determines the lifetime of nuclear fuel in a reactor: long before all possible fissions have taken place, buildup of long-lived neutron-absorbing fission products damps out the chain reaction. This is the reason that
nuclear reprocessingis a useful activity: solid spent nuclear fuelcontains about 99% of the original fissionable material present in newly manufactured nuclear fuel. Chemical separation of the fission products restores the fuel so that it can be used again.
Other potential approaches to fission product removal include solid but porous fuel which allows escape of fission products [cite web | author = Liviu Popa-Simil | url = http://www.inspi.ufl.edu/space07/program/abstracts/2060.html | title = The advantages of the poisons free fuels | date = 2007 | publisher = Space Nuclear Conference 2007 | format = abstract | accessdate = 2007-09-27] and liquid or gaseous fuel (
Molten salt reactor, Aqueous homogeneous reactor). These ease the problem of fission product accumulation in the fuel, but pose the additional problem of safely removing and storing the fission products.
Other fission products with relatively high absorption cross sections include 83Kr, 95Mo, 143Nd, 147Pm. [http://www-nds.ipen.br/sgnucdat/b3.pdf] Above this mass, even many even-
mass numberisotopes have large absorption cross sections, allowing one nucleus to serially absorb multiple neutrons.Fission of heavier actinides produces more of the heavier fission products in the lanthanide range, so the total neutron absorption cross section of fission products is higher. [ [http://lpsc.in2p3.fr/gpr/bowman/BowDynSim/BowDynSim.html BowDynSim ] ]
fast reactorthe fission product poison situation may differ significantly because neutron absorption cross sections can differ for thermal neutrons and fast neutrons. In the RBEC-M Lead-Bismuth Cooled Fast Reactor, the fission products with neutron capturemore than 5% of total fission products capture are, in order, Cs-133, Ru-101, Rh-103, Tc-99, Pd-105, Pd-107in the core, with Sm-149replacing Pd-107for 6th place in the breeding blanket. [cite web | title = RBEC-M Lead-Bismuth Cooled Fast Reactor Benchmarking Calculations | author = A. A. Dudnikov, A. A. Sedov | publisher = International Atomic Energy Agency| url = http://www.iaea.org/OurWork/ST/NE/NENP/NPTDS/Downloads/SMR_CRP1_SRWOSR/2006/RBEC-M%20Kurchatov%20Final.pdf]
In addition to fission product poisons, other materials in the reactor decay to materials that act as neutron poisons. An example of this is the decay of
tritiumto helium-3(He-3). Since tritium has a half-life of 12.3 years, normally this decay does not significantly affect reactor operations because the rate of decay of tritium is so slow. However, if tritium is produced in a reactor and then allowed to remain in the reactor during a prolonged shutdown of several months, a sufficient amount of tritium may decay to He-3 to add a significant amount of negative reactivity. Any He-3 produced in the reactor during a shutdown period will be removed during subsequent operation by a neutron-proton reaction.
During operation of a reactor the amount of fuel contained in the core constantly decreases. If the reactor is to operate for a long period of time, fuel in excess of that needed for exact criticality must be added when the reactor is built. The positive reactivity due to the excess fuel must be balanced with negative reactivity from neutron-absorbing material. Movable
control rods containing neutron-absorbing material is one method, but control rods alone to balance the excess reactivity may be impractical for a particular core design as there may be insufficient room for the rods or their mechanisms.
To control large amounts of excess fuel without control rods, burnable poisons are loaded into the core. Burnable poisons are materials that have a high neutron absorption cross section that are converted into materials of relatively low absorption cross section as the result of neutron absorption. Due to the burn-up of the poison material, the negative reactivity of the burnable poison decreases over core life. Ideally, these poisons should decrease their negative reactivity at the same rate the fuel's excess positive reactivity is depleted. Fixed burnable poisons are generally used in the form of compounds of
boronor gadoliniumthat are shaped into separate lattice pins or plates, or introduced as additives to the fuel. Since they can usually be distributed more uniformly than control rods, these poisons are less disruptive to the core's power distribution. Fixed burnable poisons may also be discretely loaded in specific locations in the core in order to shape or control flux profiles to prevent excessive flux and power peaking near certain regions of the reactor. Current practice however is to use fixed non-burnable poisons in this service.
A non-burnable poison is one that maintains a constant negative reactivity worth over the life of the core. While no neutron poison is strictly non-burnable, certain materials can be treated as non-burnable poisons under certain conditions. One example is
hafnium. The removal (by absorption of neutrons) of one isotopeof hafnium leads to the production of another neutron absorber, and continues through a chain of five absorbers. This absorption chain results in a long-lived burnable poison which approximates non-burnable characteristics."DOE Fundamentals Handbook: Nuclear Physics and Reactor Theory", page 32.]
Soluble poisons, also called chemical shim, produce a spatially uniform neutron absorption when dissolved in the water
coolant. The most common soluble poison in commercial pressurized water reactors (PWR) is boric acid, which is often referred to as soluble boron, or simply "solbor". The boric acid in the coolant decreases the thermal utilization factor, causing a decrease in reactivity. By varying the concentration of boric acid in the coolant, a process referred to as boration and dilution, the reactivity of the core can be easily varied. If the boron concentration is increased, the coolant/moderator absorbs more neutrons, adding negative reactivity. If the boron concentration is reduced (dilution), positive reactivity is added. The changing of boron concentration in a PWR is a slow process and is used primarily to compensate for fuel burnout or poison buildup. The variation in boron concentration allows control rod use to be minimized, which results in a flatter flux profile over the core than can be produced by rod insertion. The flatter flux profile occurs because there are no regions of depressed flux like those that would be produced in the vicinity of inserted control rods. This system is not in widespread use because the chemicals make the moderator temperature reactivity coefficient less negative."DOE Fundamentals Handbook: Nuclear Physics and Reactor Theory", page 31.]
Soluble poisons are also used in emergency shutdown systems. During
SCRAMthe operators can inject solutions containing neutron poisons directly into the reactor coolant. Various solutions, including sodiumpolyborate and gadolinium nitrate(Gd(NO3)3 •x H2O), are used.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Nuclear fission product — Nuclear fission products are the atomic fragments left after a large atomic nucleus fissions. Typically, a large nucleus like that of uranium fissions by splitting into two smaller nuclei, along with a few neutrons and a large release of energy… … Wikipedia
Poison (disambiguation) — Poison is a substance that causes injury, illness, or death.Poison may also refer to: * Poison (band), an American glam metal band * Poison (House episode) * The Poison , an album by Bullet For My Valentine * Poison (comics), a Marvel Comics hero … Wikipedia
Nuclear reactor technology — This article is a subarticle of Nuclear power .A nuclear reactor is a device in which nuclear chain reactions are initiated, controlled, and sustained at a steady rate, as opposed to a nuclear bomb, in which the chain reaction occurs in a… … Wikipedia
Nuclear reactor physics — See also: Critical mass Nuclear reactor physics is the branch of science that deals with the study and application of chain reaction to induce controlled rate of fission for energy in reactors. Most nuclear reactors use a chain reaction to induce … Wikipedia
Poison — This article is about the type of substance. For other uses, see Poison (disambiguation). The EU s standard toxic symbol, as defined by Directive 67/548/EEC. The skull and crossbones has long been a standard symbol for poison. In the context of… … Wikipedia
Nuclear reprocessing — technology was developed to chemically separate and recover fissionable plutonium from irradiated nuclear fuel. Reprocessing serves multiple purposes, whose relative importance has changed over time. Originally reprocessing was used solely to… … Wikipedia
Nuclear chemistry — is the subfield of chemistry dealing with radioactivity, nuclear processes and nuclear properties. It is the chemistry of radioactive elements such as the actinides, radium and radon together with the chemistry associated with equipment (such as… … Wikipedia
Nuclear warfare — Nuclear War redirects here. For other uses, see Nuclear War (disambiguation). Warfare Military history Eras Prehistoric Ancie … Wikipedia
Nuclear engineering — is the branch of engineering concerned with the application of the breakdown (fission) as well as the fusion of atomic nuclei and/or the application of other sub atomic physics, based on the principles of nuclear physics. In the sub field of… … Wikipedia
Nuclear safety — covers the actions taken to prevent nuclear and radiation accidents or to limit their consequences. This covers nuclear power plants as well as all other nuclear facilities, the transportation of nuclear materials, and the use and storage of… … Wikipedia