- Instrument landing system
The Instrument Landing System (ILS) is a ground-based
instrument approachsystem that provides precision guidance to an aircraftapproaching a runway, using a combination of radio signals and, in many cases, high-intensity lighting arrays to enable a safe landing during instrument meteorological conditions (IMC), such as low ceilings or reduced visibility due to fog, rain, or blowing snow.
Instrument Approach Procedure charts (or "
approach plates") are published for each ILS approach, providing pilots with the needed information to fly an ILS approach during instrument flight rules (IFR) operations, including the radio frequencies used by the ILS components or navaidsand the minimum visibility requirements prescribed for the specific approach.
Principle of operation
An ILS consists of two independent sub-systems, one providing lateral guidance (
Localizer), the other vertical guidance ( Glideslopeor Glide Path) to aircraft approaching a runway. Aircraft guidance is provided by the ILS receivers in the aircraft by performing a modulation depth comparison.
A localizer (LOC, or LLZ in Europe) antenna array is normally located beyond the departure end of the runway and generally consists of several pairs of directional antennas. Two signals are transmitted on one out of 40 ILS channels between the
carrier frequencyrange 108.10 MHz and 111.95 MHz (but only the odd kHz, so 108.10 108.15 108.30 and so on are LOC frequencies but 108.20 108.25 108.40 and so on are not). One is modulated at 90 Hz, the other at 150 Hz and these are transmitted from separate but co-located antennas. Each antenna transmits a narrow beam, one slightly to the left of the runway centerline, the other to the right.
The localizer receiver on the aircraft measures the
Difference in the Depth of Modulation(DDM) of the 90 Hz and 150 Hz signals. For the localizer, the depth of modulation for each of the modulating frequencies is 20 percent. The difference between the two signals varies depending on the position of the approaching aircraft from the centerline.
If there is a predominance of either 90 Hz or 150 Hz modulation, the aircraft is off the centerline. In the cockpit, the needle on the
Horizontal Situation Indicator, or HSI (The Instrument part of the ILS), or CDI ( Course deviation indicator), will show that the aircraft needs to fly left or right to correct the error to fly down the center of the runway. If the DDM is zero the aircraft is on the centerline of the localizer coinciding with the physical runway centerline.
A glideslope or Glidepath (GP) antenna array is sited to one side of the runway touchdown zone. The GP signal is transmitted on a carrier frequency between 329.15 and 335 MHz using a technique similar to that of the localizer. The centerline of the glideslope signal is arranged to define a glideslope of approximately 3° above horizontal (ground level).
Localizer and glideslope carrier frequencies are paired so that only one selection is required to tune both receivers.
These signals are displayed on an indicator in the instrument panel. This instrument is generally called the omni-bearing indicator or nav indicator. The pilot controls the aircraft so that the indications on the instrument (i.e. the course deviation indicator) remain centered on the display. This ensures the aircraft is following the ILS centreline (i.e. it provides lateral guidance). Vertical guidance, shown on the instrument by the glideslope indicator, aids the pilot in reaching the runway at the proper touchdown point. Some aircraft possess the ability to route signals into the autopilot, allowing the approach to be flown automatically by the
In addition to the previously mentioned navigational signals, the localizer provides for ILS facility identification by periodically transmitting a 1020 Hz
morse codeidentification signal. For example, the ILS for runway 04R at John F. Kennedy International Airporttransmits IJFK to identify itself, while runway 04L is known as IHIQ. This lets users know the facility is operating normally and that they are tuned to the correct ILS. The glideslope transmits no identification signal, so ILS equipment relies on the localizer for identification.
Modern localizer antennas are highly directional. However, usage of older, less directional antennas allows a runway to have a non-precision approach called a localizer back course. This lets aircraft land using the signal transmitted from the back of the localizer array. This signal is reverse sensing so a pilot may have to fly opposite the needle indication (depending on the equipment installed in the aircraft). Highly directional antennas do not provide a sufficient signal to support a backcourse. In the United States, backcourse approaches are commonly associated with Category I systems at smaller airports that do not have an ILS on both ends of the primary runway.
On most installations
marker beacons operating at a carrier frequency of 75 MHz are provided. When the transmission from a marker beacon is received it activates an indicator on the pilot's instrument panel and the tone of the beacon is audible to the pilot. The distance from the runway at which this indication should be received is promulgated in the documentation for that approach, together with the height at which the aircraft should be if correctly established on the ILS. This provides a check on the correct function of the glideslope. In modern ILS installations a DME is installed, co-located with the ILS, to augment or replace marker beacons. A DME continuously displays the aircraft's distance to the runway.
The outer marker should be located 7.2 km (3.9 NM) from the threshold except that, where this distance is not practicable, the outer marker may be located between 6.5 and 11.1 km (3.5 and 6 NM) from the threshold. The modulation is repeated Morse-style dashes of a 400 Hz tone. The cockpit indicator is a
bluelamp that flashes in unison with the received audio code. The purpose of this beacon is to provide height, distance and equipment functioning checks to aircraft on intermediate and final approach. In the United States, an NDB is often combined with the outer marker beacon in the ILS approach (called a Locator Outer Marker, or LOM); in Canada, low-powered NDBs have replaced marker beacons entirely.
The middle marker should be located so as to indicate, in low visibility conditions, the
missed approachpoint, and the point that visual contact with the runway is imminent, Ideally at a distance of approximately convert|3500|ft|m|abbr=on from the threshold. It is modulated with a 1300 Hz tone as alternating dots and dashes. The cockpit indicator is an amber lamp that flashes in unison with the received audio code.
The inner marker, when installed, shall be located so as to indicate in low visibility conditions the imminence of arrival at the runway threshold. This is typically the position of an aircraft on the ILS as it reaches Category II minima. Ideally at a distance of approximately convert|100|ft|m|abbr=on from the threshold. The modulation is Morse-style dots at 3000 Hz. The cockpit indicator is a white lamp that flashes in unison with the received audio code.
Distance measuring equipment(DME) provides pilots with a slant rangemeasurement of distance to the runway in nautical miles. DMEs are augmenting or replacing markers in many installations. The DME provides more accurate and continuous monitoring of correct progress on the ILS glideslope to the pilot, and does not require an installation outside the airport boundary. When used in conjunction with an ILS, the DME is often sited midway between the reciprocal runway thresholds with the internal delay modified so that one unit can provide distance information to either runway threshold. On approaches where a DME is specified in lieu of marker beacons, the aircraft must have at least one operating DME unit to begin the approach, and a "DME Required" restriction will be noted on the Instrument Approach Procedure.
It is essential that any failure of the ILS to provide safe guidance be detected immediately by the pilot. To achieve this, monitors continually assess the vital characteristics of the transmissions. If any significant deviation beyond strict limits is detected, either the ILS is automatically switched off or the navigation and identification components are removed from the carrier.cite web | author=Department of Transportation and Department of Defense | date=March 25, 2002 | url=http://www.navcen.uscg.gov/pubs/frp2001/FRS2001.pdf | title=2001 Federal Radionavigation Systems | format=PDF | work= | publisher= | accessmonthday=November 27 | accessyear=2005] Either of these actions will activate an indication ('failure flag') on the instruments of an aircraft using the ILS.
Some installations include medium or high intensity approach light systems. Most often, these are at larger airports. The
approach lighting system(abbreviated ALS) assists the pilot in transitioning from instrument to visual flight, and to align the aircraft visually with the runway centerline. At many non-towered airports, the intensity of the lighting system can be adjusted by the pilot, for example the pilot can click their microphone 7 times to turn on the lights, then 5 times to turn them to medium intensity.
Use of the Instrument Landing System
At large airports,
air traffic controlwill direct aircraft to the localizer via assigned headings, making sure aircraft do not get too close to each other (maintain separation), but also avoiding delay as much as possible. Several aircraft can be on the ILS at the same time, several miles apart. An aircraft that has intercepted both the localizer and the glideslope signal is said to be "established" on the approach. Typically, an aircraft will be established by convert|6|nmi|km from the runway, or just after reaching the final approach fix.
Aircraft deviation from the optimal path is indicated to the flight crew by means of display with "needles" (a carry over from when an analog meter movement would indicate deviation from the course line via voltages sent from the ILS receiver).
The output from the ILS receiver goes both to the display system (Head Down Display and
Head-Up Displayif installed) and can also go to the Flight Control Computer. An aircraft landing procedure can be either "coupled", where the Flight Control Computer directly flies the aircraft and the flight crew monitor the operation; or "uncoupled" (manual) where the flight crew fly the aircraft uses the HUD and manually control the aircraft to minimize the deviation from flight path to the runway centreline.
A useful formula pilots use to calculate the descent rate on the glideslope.
: Rate of Descent = Glideslope Angle × ( Groundspeed / 60 ) × 100
*Rate of Descent is in feet per minute
*Glideslope angle is in degrees from the horizontal (Usually 3 degrees)
*Groundspeed is in knots
If the glideslope is the standard 3 degrees then the formula can be further simplified to:
: Rate of Descent = 5 × Groundspeed
Once established on an approach, the
Autolandsystem or pilot will follow the ILS and descend along the glideslope, until the "Decision Altitude" is reached (for a typical Category I ILS, this altitude is 200 feet above the runway). At this point, the pilot must have the runway or its approach lights in sight to continue the approach.
If neither can be seen, the approach must be aborted and a "missed approach procedure" will be performed. This is where the aircraft will climb back to a predetermined altitude and position. From there the pilot will either try the same approach again, try a different approach or divert to another airport.
Aborting the approach (as well as the ATC instruction to do so) is called "executing a missed approach".
There are three categories of ILS which support similarly named categories of operation.
*Category I - A precision instrument approach and landing with a decision height not lower than ft to m|200 above touchdown zone elevation and with either a visibility not less than ft to m|2625 or a runway visual range not less than ft to m|2400, (with touchdown zone and center lightning, RVR 1,800ft). An aircraft equipped with an Enhanced Flight Vision System may, under certain circumstances, continue an approach to CAT II minimums. [14 CFR Part 91.175 amendment 281]
*Category II - Category II operation: A precision instrument approach and landing with a decision height lower than ft to m|200 above touchdown zone elevation but not lower than ft to m|100, and a runway visual range not less than ft to m|1200.
*Category III is further subdivided
**Category III A - A precision instrument approach and landing with:
***a) a decision height lower than ft to m|100 above touchdown zone elevation, or no decision height; and
***b) a runway visual range not less than ft to m|700.
**Category III B - A precision instrument approach and landing with:
***a) a decision height lower than ft to m|50 above touchdown zone elevation, or no decision height; and
***b) a runway visual range less than ft to m|700 but not less than ft to m|150.
**Category III C - A precision instrument approach and landing with no decision height and no runway visual range limitations. A Category III C system is capable of using an aircraft's autopilot to land the aircraft and can also provide guidance along the runway surface.
In each case a suitably equipped aircraft and appropriately qualified crew are required. For example, Cat IIIc requires a fail-operational system, along with a Landing Pilot (LP) who holds a Cat IIIc endorsement in their logbook , Cat I does not. A
Head-Up Displaywhich allows the pilot to perform aircraft maneuvers rather than an automatic system is considered as fail-operational. Cat I relies only on altimeter indications for decision height, whereas Cat II and Cat III approaches use radar altimeter to determine decision height. [ ICAOAnnex 10 "AERONAUTICAL TELECOMMUNICATIONS Volume 1 RADIO NAVIGATION AIDS 2.1.1"]
An ILS is required to shut down upon internal detection of a fault condition as mentioned in the monitoring section. With the increasing categories, ILS equipment is required to shut down faster since higher categories require shorter response times. For example, a Cat I localizer must shutdown within 10 seconds of detecting a fault, but a Cat III localizer must shut down in less than 2 seconds.
Limitations and alternatives
Due to the complexity of ILS localizer and glideslope systems, there are some limitations. Localizer systems are sensitive to obstructions in the signal broadcast area like large buildings or hangars. Glideslope systems are also limited by the terrain in front of the glideslope antennas. If terrain is sloping or uneven, reflections can create an uneven glidepath causing unwanted needle deflections. Additionally, since the ILS signals are pointed in one direction by the positioning of the arrays, ILS only supports straight in approaches (though a modified ILS called an Instrument Guidance System (IGS) was in use at
Kai Tak Airport, Hong Kongto accommodate a non-straight approach).Fact|date=June 2008 Installation of ILS can also be costly due to the complexity of the antenna system and siting criteria.
In the 1970s there was a major US & European effort to establish the
Microwave Landing System, which are not similarly limited and which allow curved approaches. However, a combination of slow development, airlinereluctance to invest in MLS, and the rise of GPS has resulted in its failure to be widely adopted. The Transponder Landing System(TLS) is another alternative to an ILS that can be used where a conventional ILS will not work or is not cost-effective.
Tests of the ILS system began in 1929, and the Civil Aeronautics Administration (CAA) authorized installation of the system in 1941 at six locations. The first landing of a scheduled U.S. passenger airliner using ILS was on
January 26, 1938, as a Pennsylvania-Central Airlines Boeing 247-D flew from Washington, D.C., to Pittsburgh and landed in a snowstorm using only the Instrument Landing System.
The advent of the
Global Positioning System(GPS) provides an alternative source of precision approach for aircraft. The Wide Area Augmentation System(WAAS) will provide guidance to Category I standards beginning 2007. Other methods of augmentation are in development to provide for Category III minimums or better, such as the Local Area Augmentation System(LAAS).
Instrument flight rules(IFR)
Visual flight rules(VFR)
* VHF Omni-directional Range (VOR)
Distance Measuring Equipment(DME)
* Non-Directional Beacon (NDB)
Global Positioning System(GPS)
Transponder Landing System(TLS)
Local Area Augmentation System(LAAS)
Wide Area Augmentation System(WAAS)
Beam Approach Beacon System(BABS)
* Flight director,
* ICAO Annex 10 Volume 1, Radio Navigation Aids, Fifth Edition — July 1996
* [http://www.navcen.uscg.gov/pubs/frp2001/default.htm 2001 Federal Radionavigation Plan (FRP)] —FRS publication has detailed description of ILS and other navigational systems
* [http://www.thalesatm.com/produits/1_ils.htm Thales ATM ILS page] —Manufacturer of ILS equipment; includes pictures of antenna systems
* [http://www.antennaproducts.com/ILS.html Antenna Products—ILS antenna page] —Manufacturer of ILS antennas (V-ring and traveling-wave antennas)
* [http://www.centennialofflight.gov/essay/Government_Role/landing_nav/POL14.htm History of Aircraft Landing Aids] --U.S. Centennial of Flight Commission
* [http://www.navfltsm.addr.com/ils.htm ILS Basics]
Wikimedia Foundation. 2010.
См. также в других словарях:
Instrument landing system — Pour les articles homonymes, voir ILS. L Instrument Landing System (ILS) ou Système d atterrissage aux instruments est le moyen de radio navigation le plus précis utilisé pour l atterrissage IFR. Sommaire 1 Généralités … Wikipédia en Français
Instrument Landing System — Abbildung der Sendekeulen von Localizer und Glideslopes Das Instrumentenlandesystem (engl. instrument landing system, ILS) ist ein bodenbasiertes System, das den Piloten eines Flugzeuges bei Anflug und Landung mittels zweier Leitstrahlen,… … Deutsch Wikipedia
Instrument Landing System — Pour les articles homonymes, voir ILS. Principe du Microwave Landing System, évolution de l ILS L Instrument Landing System (ILS) ou Système d atterrissage aux instruments est le moyen de radio navigation le plus … Wikipédia en Français
instrument landing system — ▪ aviation electronic guidance system designed to help airline pilots align their planes with the centre of a landing strip during final approach under conditions of poor visibility. The ground equipment of the ILS consists of two… … Universalium
instrument landing system — A radio aid to navigation intended to facilitate aircraft in landing. It provides lateral and vertical guidance to the optimum point of landing. The various components of an instrument landing system are the localizer, which guides the aircraft… … Aviation dictionary
instrument landing system — prietaisinė tūpimo sistema statusas T sritis radioelektronika atitikmenys: angl. instrument landing system vok. Instrumentenlandesystem, n rus. система посадки по приборам, f pranc. système d atterrissage par instruments, m … Radioelektronikos terminų žodynas
instrument landing system — tūpimo pagal prietaisus sistema statusas T sritis Gynyba apibrėžtis Radionavigacinė tūpimo sistema, padedanti valdyti orlaivį vertikalioje ir horizontalioje plokštumose. Kartais rodo atstumą iki tūpimo taško. atitikmenys: angl. instrument landing … NATO terminų aiškinamasis žodynas
instrument landing system — A system of radio navigation intended to assist aircraft in landing which provides lateral and vertical guidance, which may include indications of distance from the optimum point of landing. Also called ILS … Military dictionary
Instrument Landing System — ILS, radio system in an airport that directs a pilot in landing an aircraft in conditions of limited visibility … English contemporary dictionary
instrument landing system — noun a radio navigation landing aid which provides an approaching aircraft with lateral and vertical guidance and with marker beacon indications at specified points … Australian English dictionary