Bourke engine

Bourke engine

The Bourke Engine was designed by Russell Bourke in the 1920s, as an improved two-stroke engine. Despite finishing his design and building several working engines, the onset of World War II, lack of test results,[1] and the poor health of his wife compounded to prevent his engine from ever coming successfully to market. The main claimed virtues of the design are that it has only two moving parts, is light weight, powerful, has two power pulses per revolution, and does not need oil mixed into the fuel.



The Bourke engine is basically a two-stroke design, with one horizontally opposed piston assembly using two pistons that move in the same direction at the same time, so that their operations are 180 degrees out of phase. The pistons are connected to a Scotch Yoke mechanism in place of the more usual crankshaft mechanism, thus the piston acceleration is perfectly sinusoidal. This causes the pistons to spend more time at top dead center than conventional engines, allowing hydrogen detonation of the fuel to occur. The incoming charge is compressed in a chamber under the pistons, as in a conventional crankcase-charged two-stroke engine. The connecting-rod seal prevents the fuel from contaminating the bottom-end lubricating oil.


The operating cycle is very similar to that of a current production spark ignition two-stroke with crankcase compression, with two modifications:

  1. The fuel is injected directly into the air as it moves through the transfer port.
  2. The engine is designed to run without using spark ignition once it is warmed up. This is known as auto-ignition or dieseling, and the air/fuel mixture starts to burn due to the high temperature of the compressed gas, and/or the presence of hot metal in the combustion chamber.

Design features

The following design features have been identified

Mechanical features

  • Scotch yoke instead of connecting rods to translate linear motion to rotary motion
  • Fewer moving parts (only 2 moving assemblies per opposed cylinder pair) and the opposed cylinders are combinable to make 2, 4, 6, 8, 10, 12 or any even number of cylinders
  • Smoother operation due to elimination of crank and slider mechanism
  • The piston is connected to the Scotch yoke through a slipper bearing (a type of hydrodynamic tilting-pad fluid bearing)
  • Mechanical fuel injection.
  • Ports rather than valves.
  • Easy maintenance (top overhauling) with simple tools.
  • The Scotch yoke does not create lateral forces on the piston, reducing friction, vibration and piston wear.
  • O-rings are used to seal joints rather than gaskets.
  • The use of the Scotch Yoke reduces vibration from the motions of the connecting rod—for example, the peak acceleration in a Scotch yoke is 25% less than the acceleration in a conventional crank and slider arrangement. The piston movement and therefore vibration is sinusoidal so the engine could theoretically be perfectly counterbalanced, unlike a conventional engine which has harmonics in the piston movement courtesy of the lateral movement of the crankpin.
  • The Scotch Yoke makes the pistons dwell very slightly longer at top dead center, so the fuel burns more completely in a smaller volume.

Gas flow and thermodynamic features

  • Low exhaust temperature (below that of boiling water) so metal exhaust components are not required, plastic ones can be used if strength is not required from exhaust system
  • Extremely fast hydrogen detonation burn time of the lean mixture so the engine can be considered to be a hydrogen detonation (i.e., explosion not deflagration) engine.
  • 15:1 to 24:1 compression ratio for high efficiency and it can be easily changed as required by different fuels and operation requirements.
  • Fuel is vaporised when it is injected into the transfer ports, and the turbulence in the intake manifolds and the piston shape above the rings stratifies the fuel air mixture into the combustion chamber.
  • Lean burn for increased efficiency and reduced emissions.


  • This design uses oil seals to prevent the pollution from the combustion chamber (created by piston ring blow-by in four-strokes and just combustion in two-strokes) from polluting the crankcase oil, extending the life of the oil as it is used slowly for keeping the rings full of oil to hold and use to lubricate. Oil was shown to be used slowly by the dropfull as needed, but checking the quantity and cleanness of it was still recommended by Russell Bourke, its creator.
  • The lubricating oil in the base is protected from combustion chamber pollution by an oil seal over the connecting rod.
  • The piston rings are supplied with oil from a small supply hole in the cylinder wall at bottom dead center.

Claimed and measured performance

  • Efficiency 0.25 (lb/h)/hp is claimed - about the same as the best diesel engine,[2] or roughly twice as efficient as the best two strokes. This is equivalent to a thermodynamic efficiency of 55.4%, which is an exceedingly high figure for a small internal combustion engine. In a test witnessed by a third party, the actual fuel consumption was 1.1 hp/(lb/h),[3] or 0.9 (lb/h)/hp, equivalent to a thermodynamic efficiency of about 12.5%, which is typical of a 1920s steam engine.[4]
  • Power to weight 0.9[5] to 2.5 hp/lb is claimed, although no independently witnessed test to support this has been documented. The upper range of this is roughly twice as good as the best four-stroke production engine shown here,[6] or 0.1 hp/lb better than a Graupner G58 two-stroke.[7] The lower claim is unremarkable, easily exceeded by production four-stroke engines, never mind two strokes.[8]
  • Emissions Achieved virtually no hydrocarbons (80 ppm) or carbon monoxide (less than 10 ppm) in published test results, however no power output was given for these results, and NOx was not measured.
  • Low Emissions The engine is claimed to be able to operate on hydrogen or any hydro-carbon fuel without any modifications, producing only water vapor and carbon dioxide as emissions.

Engineering critique of the Bourke engine

The Bourke Engine has some interesting features, but the extravagant claims[9] for its performance are unlikely to be borne out by real tests[citation needed]. Many of the claims are contradictory.[10]

  1. Seal friction from the seal between the air compressor chamber and the crankcase, against the connecting rod, will reduce the efficiency.[11]
  2. Efficiency will be reduced due to pumping losses, as the air charge is compressed and expanded twice but energy is only extracted for power in one of the expansions per piston stroke.[12][13]
  3. Engine weight is likely to be high because it will have to be very strongly built to cope with the high peak pressures seen as a result of the rapid high temperature combustion.[14]
  4. Each piston pair is highly imbalanced as the two pistons move in the same direction at the same time, unlike in a boxer engine.[15] This will limit the speed range and hence the power of the engine, and increase its weight due to the strong construction necessary to react the high forces in the components.[16]
  5. High speed two-stroke engines tend to be inefficient compared with four-strokes because some of the intake charge escapes unburnt with the exhaust.[17]
  6. When the charge is transferred from the compressor chamber to the combustion chamber it will cool down, reducing the efficiency[citation needed] of the engine.[18]
  7. Use of excess air will reduce the torque available for a given engine size.[19]
  8. Forcing the exhaust out rapidly through small ports will incur a further efficiency loss.[20]
  9. Operating an internal combustion engine in detonation reduces efficiency due to heat lost from the combustion gases being scrubbed against the combustion chamber walls by the shock waves.[21]
  10. Emissions - although some tests have shown low emissions in some circumstances, these were not necessarily at full power. As the scavenge ratio (i.e. engine torque) is increased more HC and CO will be emitted.[22]
  11. Increased dwell time at TDC will allow more heat to be transferred to the cylinder walls, reducing the efficiency.[23]
  12. When running in auto-ignition mode the timing of the start of the burn is controlled by the operating state of the engine, rather than directly as in a spark ignition or diesel engine. As such it may be possible to optimize it for one operating condition, but not for the wide range of torques and speeds that an engine typically sees. The result will be reduced efficiency and higher emissions.[24]
  13. If the efficiency is high, then combustion temperatures must be high, as required by the Carnot cycle, and the air fuel mixture must be lean. High combustion temperatures and lean mixtures cause nitrogen dioxide to be formed.


  1. ^ New Page 1
  2. ^ The Most Powerful Diesel Engine in the World
  3. ^ The Bourke Engine
  4. ^ GS Baker "Ship Form, Resistance, and Screw Propulsion" p215
  5. ^ Bourke Engine Com
  6. ^
  7. ^ Unbenannt-1
  8. ^ aircraft engine development
  9. ^ Bourke Engine#Claimed and measured performance
  10. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 pp240-245|Trade-off between efficiency, emissions and power
  11. ^ |Friction of seals
  12. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 p723|Pumping losses
  13. ^ C Feyette Taylor "The Internal Combustion Engine" 4th edition, p194 para 2-3, p205 fig 124b, p258|Pumping losses in two strokes
  14. ^ C Feyette Taylor "The Internal Combustion Engine" 4th edition, p119|stresses due to detonation
  15. ^ Engine balance#Single-cylinder engines Balance of single-cylinder engines
  16. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 p20|Importance of primary balance
  17. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 pp240-245, p881|Scavenging ratio and low efficiency
  18. ^ adiabatic expansion
  19. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 pp240-245|Scavenging ratio effect on torque output
  20. ^ C Feyette Taylor "The Internal Combustion Engine" 4th edition p194 para5|Pumping losses in two strokes
  21. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 p452-3|Increased thermal losses due to detonation
  22. ^ JB Heywood "Internal Combustion Engine Fundamentals" ISBN 0-07-100499-8 pp240-245, p881|Scavenging ratio and high emissions
  23. ^ Science Links Japan | Effect of Piston Speed around Top Dead Center on Thermal Efficiency
  24. ^ Hot bulb engine

External links

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Bourke — may refer to: * Bourke, New South Wales * Richard Bourke, Governor of New South Wales from 1831 1837 * Martin Bourke, Governor of Turks and Caicos Islands from 1993 to 1996 * Bourke engine * Bourke s Parrot * Bourke Street, Melbourne, a street in …   Wikipedia

  • Bourke-Motor — Dieser Artikel oder Abschnitt bedarf einer Überarbeitung. Näheres ist auf der Diskussionsseite angegeben. Hilf mit, ihn zu verbessern, und entferne anschließend diese Markierung. Ein Kurbelschlaufenmotor ist ein Verbrennungsmotor nach dem Prinzip …   Deutsch Wikipedia

  • Engine knocking — Pinging redirects here. For other uses, see Ping (disambiguation). Knocking (also called knock, detonation, spark knock, pinging or pinking) in spark ignition internal combustion engines occurs when combustion of the air/fuel mixture in the… …   Wikipedia

  • Two-stroke engine — Brons two stroke V8 Diesel engine driving a Heemaf generator. A two stroke engine is an internal combustion engine that completes the process cycle in one revolution of the crankshaft (an up stroke and a down stroke of the piston, compared to… …   Wikipedia

  • Four-stroke engine — Four stroke cycle used in gasoline/petrol engines. The right blue side is the intake and the left yellow side is the exhaust. The cylinder wall is a thin sleeve surrounded by cooling liquid. A video montage of the Otto engines running at the… …   Wikipedia

  • Corliss steam engine — A Corliss steam engine – the valve gear is on the right of the cylinder block, on the left of the picture A Corliss steam engine (or Corliss engine) is a steam engine, fitted with rotary valves and with variable valve timing patented in 1849 …   Wikipedia

  • Opposed-piston engine — This article is about existing engine designs. For the quite different concept proposed by Frank Stelzer, see Stelzer engine. Fairbanks Morse opposed piston diesel engines on the submarine USS Pampanito An opposed piston engine is a reciprocating …   Wikipedia

  • Controlled Combustion Engine — REVETEC X4v2 Prototype Engine Controlled Combustion Engine (CCE) is a term used by Revetec, an engine design company, to identify a type of experimental internal combustion engine (ICE) designed by Brad Howell Smith. It uses two counter rotating… …   Wikipedia

  • Stroke (engine) — Reciprocating motion, used in reciprocating engines and other mechanisms, is back and forth motion. Each cycle of reciprocation consists of two opposite motions: there is a motion in one direction, and then a motion back in the opposite direction …   Wikipedia

  • Marine automobile engine — Volkswagen Marine 3.0 litre V6 TDI 265 6 marine engine. This is a marine modified version of Volkswagen Groups 3.0 V6 24v TDI CR automobile engine. Marine automobile engines are types of automobile petrol or diesel engines that have been… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.