- Surface-mount technology
Surface-mount technology (SMT) is a method for constructing electronic circuits in which the components (SMC, or Surface Mounted Components) are mounted directly onto the surface of
printed circuit boards (PCBs). Electronic devices so made are called "surface-mount devices" or SMDs. In the industry it has largely replaced the through-hole technologyconstruction method of fitting components with wire leads into holes in the circuit board.
An SMT component is usually smaller than its through-hole counterpart because it has either smaller leads or no leads at all. It may have short pins or leads of various styles, flat contacts, a matrix of solder balls (BGAs), or terminations on the body of the component.
Surface-mount technology was developed in the 1960s and became widely used in the late 1980s.Much of the pioneering work in this technology was by
IBM. The design approach first demonstrated by IBM in 1960 in a small-scale computer was later applied in the Launch Vehicle Digital Computer used in the Instrument Unit that guided all Saturn IBand Saturn Vvehicles. (See Saturn Launch Vehicle Digital Computerarticle for a description of this type of electronic packaging as of 1964.)Components were mechanically redesigned to have small metal tabs or end caps that could be directly soldered to the surface of the PCB. Components became much smaller and component placement on both sides of a board became far more common with surface-mounting than through-hole mounting, allowing much higher circuit densities. Often only the solder joints hold the parts to the board, although parts on the bottom or "second" side of the board are temporarily secured with a dot of adhesive as well.Surface-mounted devices (SMDs) are usually made physically small and lightweight for this reason. Surface mounting lends itself well to a high degree of automation, reducing labor cost and greatly increasing production rates. SMDs can be one-quarter to one-tenth the size and weight, and one-half to one-quarter the cost of equivalent through-hole parts
Where components are to be placed, the printed circuit board has flat, usually
tin-lead, silver, or gold plated copperpads without holes, called "solder pads". Solder paste, a sticky mixture of flux and tiny solder particles, is first applied to all the solder pads with a stainless steel stencil. If components are to be mounted on the second side, a numerically controlled(NC) machine places small liquid adhesive dots at the locations of all second-side components. The boards then proceed to the pick-and-place machines, where they are placed on a conveyor belt. Small SMDs are usually delivered to the production line on paper or plastic tapes wound on reels. Integrated circuits are typically delivered stacked in static-free plastic tubes or trays. NC pick-and-place machines remove the parts from the reels or tubes and place them on the PCB. Second-side components are placed first, and the adhesive dots are quickly cured with application of low heat or ultravioletradiation. The boards are flipped over and first-side components are placed by additional NC machines.
The boards are then conveyed into the
reflow solderingoven. They first enter a pre-heat zone, where the temperature of the board and all the components is gradually, uniformly raised. This helps minimize thermal stresses when the assemblies cool down after soldering. The boards then enter a zone where the temperature is high enough to melt the solder particles in the solder paste, bonding the component leads to the pads on the circuit board. The surface tension of the molten solder helps keep the components in place, and if the solder pad geometries are correctly designed, surface tensionautomatically aligns the components on their pads. There are a number of techniques for reflowing solder. One is to use infraredlamps; this is called infrared reflow. Another is to use a hot gas. At one time special fluorocarbonliquids with high boiling points were used in a method called vapor phase reflow. Due to environmental concerns, this method is falling out of favor. Today, it is more common to use nitrogen gas or nitrogen gas enriched air in a convection oven. Each method has its advantages and disadvantages. With infrared reflow, the board designer must lay the board out so that short components don't fall into the shadows of tall components. Component location is less restricted if the designer knows that vapor phase reflow or convection soldering will be used in production. Following reflow soldering, certain irregular or heat-sensitive components may be installed and soldered by hand, or in large scale automation, by focused infrared beam (FIB) equipment.
After soldering, the boards are washed to remove flux residue and any stray solder balls that could short out closely spaced component leads.
Rosinflux is removed with fluorocarbon solvents, high flash point hydrocarbonsolvents, or limonene(derived from orange peels). Water soluble fluxes are removed with deionized water and detergent, followed by an air blast to quickly remove residual water. When aesthetics are unimportant and the flux doesn't cause shorting or corrosion, flux residues are sometimes left on the boards, saving the cost of cleaning and eliminating the waste disposal.
Finally, the boards are visually inspected for missing or misaligned components and solder bridging. If needed, they are sent to a rework station where a human operator corrects any errors. They are then sent to the testing stations to verify that they operate correctly.
The main advantages of SMT over the older through-hole technique are:
* Much higher number of components and many more connections per component
* Fewer holes need to be drilled through abrasive boards
* Simpler automated assembly
* Small errors in component placement are corrected automatically (the surface tension of the molten solder pulls the component into alignment with the solder pads)
* Components can be placed on both sides of the circuit board
* Lower resistance and inductance at the connection (leading to better performance for high frequency parts)
* Better mechanical performance under shake and vibration conditions
* SMT parts generally cost less than through-hole parts
* Fewer unwanted RF signal effects in SMT parts when compared to leaded parts, yielding better predictability of component characteristics.
* The manufacturing processes for SMT are much more sophisticated than through-hole boards, raising the initial cost and time of setting up for production
* Manual prototype assembly or component-level repair is more difficult (more so without a steady hand and the right tools) given the very small sizes and lead spacings of many SMDs.
* SMDs can't be used with breadboards (a quick snap-and-play prototyping tool), requiring a custom PCB for every prototype. The PCB costs dozens to hundreds of dollars to fabricate and must be designed with specialized software.
Reworking defective SMD components
Defective surface mount components can be repaired in two ways: by using soldering irons (depends on the kind and number of connections) or using a professional rework system. In most cases a rework system is the first choice because the human influence on the rework result is very low. Generally, two essential soldering methods can be distinguished: infrared soldering and soldering with hot gas.
Benefits and Disadvantages of different soldering methods
During infrared soldering, the energy for heating up the solder joint will be transmitted by long or short wave electromagnetic radiation.
* Easy setup
* No compressed air required
* No component-specific nozzles (low costs)
* Fast reaction of infrared source (depends on used system)"Disadvantages"
* Central areas will be heated more than peripheral areas
* Temperature can hardly be controlled, peaks cannot be ruled out
* Covering of the neighboured components is necessary
* No component-specific nozzles but covering neighbored components (to prevent damage) needs additional time for every board
* Surface temperature depends on the component's reflection characteristics: dark surfaces will be heated more than lighter surfaces
* The temperature additionally depends on the surface shape. Convective loss of energy will reduce the temperature of the component
* No reflow atmosphere possible
Conventional hot gas soldering
During hot gas soldering, the energy for heating up the solder joint will be transmitted by a gaseous medium. This can be air or inert gas (nitrogen).
* Simulating reflow oven atmosphere
* Switching between hot gas and nitrogen (economic use)
* Standard and component-specific nozzles allow high reliability and reduced process time
* Allow reproducible soldering profiles
* Efficient heating, large heat amounts can be transmitted
* Even heating of the affected board area
* Temperature of the component will never exceed the adjusted gas temperature
* Rapid cool down after reflow, resulting in small-grained solder joints (depends on used system)
* Thermal capacity of the heat generator results in slow reaction whereby thermal profiles can be distorted (depends on used system)
A rework process usually undoes some type of error, either human or machine-generated, and includes the following steps:
* Melt solder and component removal
* Residual solder removal
* Printing of solder paste on PCB, direct component printing or dispensing
* Placement and reflow of new component.
Sometimes hundreds or thousands of the same part need to be repaired. Such errors, if due to assembly, are often caught during the process, however a whole new level of rework arises when component failure is discovered too late, and perhaps unnoticed until the end user experiences them. Rework may also be used if high-value products require revisions, and re-engineering, perhaps to change a single firmware based component, may revive a once obsolete product. These tasks require a rework operation specifically designed to repair/replace components in volume.
Eutecticsolder can also be used for low-volume manual rework.
Surface-mount components are usually smaller than their counterparts with leads, and are designed to be handled by machines rather than by humans. The electronics industry has standardized package shapes and sizes (the leading standardisation body is
JEDEC). These include:
**Rectangular passive components (mostly
resistors and capacitors):
***01005 (0402 metric) : 0.016" × 0.008" (0.4 mm × 0.2 mm) Typical power rating for resistors 1/32 Watt
***0201 (0603 metric) : 0.024" × 0.012" (0.6 mm × 0.3 mm) Typical power rating for resistors 1/20 Watt
***0402 (1005 metric) : 0.04" × 0.02" (1.0 mm × 0.5 mm) Typical power rating for resistors 1/16 Watt
***0603 (1608 metric) : 0.063" × 0.031" (1.6 mm × 0.8 mm) Typical power rating for resistors 1/16 Watt
***0805 (2012 metric) : 0.08" × 0.05" (2.0 mm × 1.25 mm) Typical power rating for resistors 1/10 or 1/8 Watt
***1206 (3216 metric) : 0.126" × 0.063" (3.2 mm × 1.6 mm) Typical power rating for resistors 1/4 Watt
***1806 (4516 metric) : 0.177" × 0.063" (4.5 mm × 1.6 mm)
***1812 (4532 metric) : 0.18" × 0.12" (4.5 mm × 3.2 mm) Typical power rating for resistors 1/2 Watt
***2010 (5025 metric) : 0.2" × 0.1" (5.0 mm × 2.5 mm)
***2512 (6332 metric) : 0.25" × 0.12" (6.35 mm × 3.0 mm)
Tantalumcapacitors [http://www.vatronics.com/tancap/smdtantalumcapacitors.pdf] :
***EIA 3216-12 ( [http://www.kemet.com Kemet] S, [http://www.avx.com/ AVX] S): 3.2 mm × 1.6 mm × 1.2 mm
***EIA 3216-18 (Kemet A, AVX A): 3.2 mm × 1.6 mm × 1.8 mm
***EIA 3528-12 (Kemet T, AVX T): 3.5 mm × 2.8 mm × 1.2 mm
***EIA 3528-21 (Kemet B, AVX B): 3.5 mm × 2.8 mm × 2.1 mm
***EIA 6032-15 (Kemet U, AVX W): 6.0 mm × 3.2 mm × 1.5 mm
***EIA 6032-28 (Kemet C, AVX C): 6.0 mm × 3.2 mm × 2.8 mm
***EIA 7260-38 (Kemet E, AVX V): 7.2 mm × 6.0 mm × 3.8 mm
***EIA 7343-20 (Kemet V, AVX Y): 7.3 mm × 4.3 mm × 2.0 mm
***EIA 7343-31 (Kemet D, AVX D): 7.3 mm × 4.3 mm × 3.1 mm
***EIA 7343-43 (Kemet X, AVX E): 7.3 mm × 4.3 mm × 4.3 mm
** SOD: Small Outline Diode
***SOD-323: 1.7 × 1.25 × 0.95 mm
***SOD-123: 3.68 × 1.17 × 1.60 mm
***SOD-80C: 3.50mm × 1.50mm × More info [http://www.cdil.com/package/sod_80c.pdf]
**MELF — Metal Electrode Leadless Face — (mostly
resistors and diodes): Barrel shaped components, dimensions do not match those of rectangular references for identical codes.
***MicroMelf (MMU) Size 0102: L:2.2mm D:1.1mm (solder pad fits rectangular 0805) 1/5 Watt (0.2W) 100V
***MiniMelf (MMA) Size 0204: L:3.6mm D:1.4mm (solder pad fits rectangular 1206) 1/4 Watt (0.25W) 200V
***Melf (MMB) Size 0207: L:5.8mm D:2.2mm 1 Watt (1.0W) 500V
transistor, with three terminals
***SOT-23: 3 mm × 1.75 mm × 1.3 mm body - three terminals for a transistor, or up to eight terminals for an integrated circuit
***SOT-223: 6.7 mm × 3.7 mm × 1.8 mm body - four terminals, one of which is a large heat-transfer pad
**DPAK (TO-252): discrete packaging. Developed by
Motorolato house higher powered devices. Comes in three- or five-terminal versions [http://www.infineon.com/cgi-bin/ifx/portal/ep/programView.do?channelId=-71967&programId=36207&programPage=%2Fep%2Fprogram%2Fpackage.jsp&pageTypeId=17099]
**D2PAK (TO-263) - bigger than the DPAK; basically a surface mount equivalent of the
TO220through-hole package. Comes in 3, 5, 6, 7, 8 or 9-terminal versions [http://www.infineon.com/cgi-bin/ifx/portal/ep/programView.do?channelId=-71967&programId=36208&programPage=%2Fep%2Fprogram%2Fpackage.jsp&pageTypeId=17099]
**D3PAK (TO-268) - even larger than D2PAK [http://www.fairchildsemi.com/products/discrete/packaging/TO_268.html]
*Packages with four or more terminals "(drawings of most of the following packages can be found on [http://www.intersil.com/design/packages/plastic.asp] )"
Small-outline integrated circuit(SOIC) - small-outline integrated circuit, dual-in-line, 8 or more pins, gull-wing lead form, pin spacing 1.27 mm
***J-Leaded Small Outline Package (SOJ) - the same as SOIC except
***TSOP - thin small-outline package, thinner than SOIC with smaller pin spacing of 0.5 mm
***SSOP - Shrink Small-Outline Package, pin spacing of 0.635 mm or in some cases 0.8mm
TSSOP- Thin Shrink Small-Outline package.
QSOP- Quarter-Size Small-Outline package, with pin spacing of 0.635 mm
***VSOP - Very Small Outline Package, even smaller than QSOP; 0.4, 0.5 mm or 0.65 mm pin spacing
***PLCC - plastic leaded chip carrier, square, J-lead, pin spacing 1.27 mm
QFP- Quad Flat Package, various sizes, with pins on all four sides
LQFP- Low-profile Quad Flat Package, 1.4 mm high, varying sized and pins on all four sides
PQFP- plastic quad flat-pack, a square with pins on all four sides, 44 or more pins
CQFP- ceramic quad flat-pack, similar to PQFP
MQFP- Metric Quad Flat Pack, a QFP package with metric pin distribution
TQFP- thin quad flat pack, a thinner version of PQFP
QFN- quad flat pack, no-leads, smaller footprint than leaded equivalent
***LCC - Leadless Chip Carrier, contacts are recessed vertically to "wick-in" solder. Common in aviation electronics because of robustness to mechanical vibration.
***MLP - Leadframe package with a 0.5 mm contact pitch, no leads [http://www.carsem.com/services/mlp_dd.php]
PQFN- power quad flat-pack, no-leads, with exposed die-pad [s] for heatsinking
***PGA - Pin grid array.
***BGA - ball grid array, with a square or rectangular array of solder balls on one surface, ball spacing typically 1.27 mm
***LGA - Same Manufacture process of BGA, has Advantage being cooler than BGA by quick Heat Deception feature. No Balls only Patch.
FBGA- fine pitch ball grid array, with a square or rectangular array of solder balls on one surface
LFBGA- low profile fine pitch ball grid array, with a square or rectangular array of solder balls on one surface, ball spacing typically 0.8 mm
TFBGA- thin fine pitch ball grid array, with a square or rectangular array of solder balls on one surface, ball spacing typically 0.5 mm
***CGA - column grid array, circuit package in which the input and output points are high temperature solder cylinders or columns arranged in a grid pattern.
***CCGA - ceramic column grid array, circuit package in which the input and output points are high temperature solder cylinders or columns arranged in a grid pattern. The body of the component is ceramic.
***μBGA - micro-BGA, with ball spacing less than 1 mm
***LLP - Lead Less Package, a package with metric pin distribution (0.5 mm pitch).
**Non-packaged devices (although surface mount, these devices require specific process for assembly):
***COB - chip-on-board; a bare
siliconchip, that is usually an integrated circuit, is supplied without a package (usually a lead frame overmolded with epoxy) and is attached, often with epoxy, directly to a circuit board. The chip is then wire bonded and protected from mechanical damage and contamination by an epoxy "glob-top".
***COF - chip-on-flex; a variation of COB, where a chip is mounted directly to a
***COG - chip-on-glass; a variation of COB, where a chip is mounted directly to a piece of glass - typically an
There are often subtle variations in package details from manufacturer to manufacturer, and even though standard designations are used, designers need to confirm dimensions when laying out printed circuit boards.
Printed circuit board
Electronics Manufacturing Services
SMT placement equipment
Plastic leaded chip carrier(PLCC)
* [http://www.finetech.de/enid/microhvr#MicroHVR_video_youtube Video: automatic rework of µBGA SMD components]
* [http://www.smtnet.com/ SMTnet (Surface Mount Technology Industry Portal)]
* [http://www.smtmag.com/ SMT Magazine]
* [http://www.bimbel.de/artikel/artikel-17.html SMT-Soldering by hand] (German language with pictures)
* [http://www.speleogroup.org/files/SMT-boards-sg.pdf Manual SMT board assembly and soldering (PDF)] (with interesting gadget for holding SMT components)
* [http://www.seattlerobotics.org/encoder/200006/oven_art.htm DIY SMT oven]
point-to-point constructionwith SMT components, instead of a custom PCB: [http://elm-chan.org/docs/wire/wiring_e.html Progressive Wiring Techniques]
* [http://catalog.tycoelectronics.com/catalog/common/images/PartImages/chip_res_padsz.jpgSolder Pad Layout Dimensions]
Wikimedia Foundation. 2010.
См. также в других словарях:
Surface-mount technology — Technique de montage en surface Pour les articles homonymes, voir SMT. La technique de montage en surface (TMS, de l anglais Surface Mount Technology, SMT) est une technique qui permet de fixer des composants électroniques à la surface d un… … Wikipédia en Français
Surface Mount Technology — Technique de montage en surface Pour les articles homonymes, voir SMT. La technique de montage en surface (TMS, de l anglais Surface Mount Technology, SMT) est une technique qui permet de fixer des composants électroniques à la surface d un… … Wikipédia en Français
Mount Washington (New Hampshire) — Mount Washington Mount Washington, from Bretton Woods. The cog railway track is visible, on the spur to the left of the summit … Wikipedia
Mount Pleasant Caldera — Elevation approx. 248 m (814 ft) Listing List of volcanoes in Canada … Wikipedia
Mount Isa Mines — Location … Wikipedia
Mount Kenya — Elevation 5,199 m (17,057 ft) … Wikipedia
Mount Kinabalu — Gunung Kinabalu Mount Kinabalu Elevation … Wikipedia
Mount Vesuvius — This article is about the mountain/volcano in Italy. For other uses, see Vesuvius (disambiguation). Mount Vesuvius Monte Vesuvio … Wikipedia
Mount Carmel High School (Chicago) — For other schools with the same name, see Mount Carmel High School (disambiguation). For the other Illinois school with the same name, see Mount Carmel High School (Mount Carmel, Illinois). Mt. Carmel High School Zelo Zelatus Sum Pro Domino Deo… … Wikipedia
Mount Poso Oil Field — The Mount Poso Oil Field in Kern County, California. Other oil fields are shown in gray. The Mount Poso Oil Field is a large oil and gas field in the lower foothills of the Sierra Nevada Mountains in Kern County, California. Discovered in 1926,… … Wikipedia