# Young's modulus

﻿
Young's modulus

In solid mechanics, Young's modulus (E) is a measure of the stiffness of an isotropic elastic material. It is also known as the Young modulus, modulus of elasticity, elastic modulus (though Young's modulus is actually one of several elastic moduli such as the bulk modulus and the shear modulus) or tensile modulus. It is defined as the ratio of the uniaxial stress over the uniaxial strain in the range of stress in which Hooke's Law holds. [GoldBookRef|title=modulus of elasticity (Young's modulus), "E"|file=M03966] This can be experimentally determined from the slope of a stress-strain curve created during tensile tests conducted on a sample of the material.

Young's modulus is named after Thomas Young, the 18th century British scientist. However, the concept was developed in 1727 by Leonhard Euler, and the first experiments that used the concept of Young's modulus in its current form were performed by the Italian scientist Giordano Riccati in 1782 — predating Young's work by 25 years. ["The Rational Mechanics of Flexible or Elastic Bodies, 1638-1788": Introduction to Leonhardi Euleri Opera Omnia, vol. X and XI, Seriei Secundae. Orell Fussli.]

Units

Young's modulus is the ratio of stress, which has units of pressure, to strain, which is dimensionless; therefore Young's modulus itself has units of pressure. A purist might argue that the units are fine if the dimensionless ratio is left in (i.e. lbs/in^2 over in/in). Carrying the full expression can be helpful for canceling units, in dimensional analysis.

The SI unit of modulus of elasticity (E, or less commonly Y) is the pascal; the practical units are megapascals (MPa) or gigapascals (GPa or kN/mm²). In United States customary units, it is expressed as pounds (force) per square inch (psi).

Usage

The Young's modulus allows the behavior of a bar made of an isotropic elastic material to be calculated under tensile or compressive loads. For instance, it can be used to predict the amount a wire will extend under tension or buckle under compression. Some calculations also require the use of other material properties, such as the shear modulus, density, or Poisson's ratio.

Linear "versus" non-linear

For many materials, Young's modulus is essentially constant over a range of strains. Such materials are called linear, and are said to obey Hooke's law. Examples of linear materials include steel, carbon fiber, and glass. Rubber and soils (except at very small strains) are non-linear materials.

Directional materials

Young's modulus is not always the same in all orientations of a material. Most metals and ceramics, along with many other materials, are isotropic: Their mechanical properties "are" the same in all orientations. However, metals and ceramics can be treated with certain impurities, and metals can be mechanically 'worked,' to make their grain structures directional. These materials then become anisotropic, and Young's modulus will change depending on which direction the force is applied from. Anisotropy can be seen in many composites as well. For example, carbon fiber has a much higher Young's modulus (is much stiffer) when force is loaded parallel to the fibers (along the grain), and is an example of a material with transverse isotropy. Other such materials include wood and reinforced concrete.Engineers can use this directional phenomenon to their advantage in creating various structures in our environment.

Calculation

Young's modulus, "E", can be calculated by dividing the tensile stress by the tensile strain:

:$E equiv frac\left\{mbox \left\{tensile stress\left\{mbox \left\{tensile strain = frac\left\{sigma\right\}\left\{varepsilon\right\}= frac\left\{F/A_0\right\}\left\{Delta L/L_0\right\} = frac\left\{F L_0\right\} \left\{A_0 Delta L\right\}$

where:E is the Young's modulus (modulus of elasticity):F is the force applied to the object;:A0 is the original cross-sectional area through which the force is applied;:ΔL is the amount by which the length of the object changes;:L0 is the original length of the object.

Force exerted by stretched or compressed material

The Young's modulus of a material can be used to calculate the force it exerts under a specific strain.

:$F = frac\left\{E A_0 Delta L\right\} \left\{L_0\right\}$where F is the force exerted by the material when compressed or stretched by ΔL.

From this formula can be derived Hooke's law, which describes the stiffness of an ideal spring: :$F = left\left( frac\left\{E A_0\right\} \left\{L_0\right\} ight\right) Delta L = k x ,$ where::$x = Delta L. ,$

Elastic potential energy

The elastic potential energy stored is given by the integral of this expression with respect to L:

:$U_e = int \left\{frac\left\{E A_0 Delta L\right\} \left\{L_0, dL = frac \left\{E A_0\right\} \left\{L_0\right\} int \left\{ Delta L \right\}, dL = frac \left\{E A_0 \left\{Delta L\right\}^2\right\} \left\{2 L_0\right\}$

where Ue is the elastic potential energy.

The elastic potential energy per unit volume is given by::$frac\left\{U_e\right\} \left\{A_0 L_0\right\} = frac \left\{E \left\{Delta L\right\}^2\right\} \left\{2 L_0^2\right\} = frac \left\{1\right\} \left\{2\right\} E \left\{varepsilon\right\}^2$, where $varepsilon = frac \left\{Delta L\right\} \left\{L_0\right\}$ is the strain in the material.

This formula can also be expressed as the integral of Hooke's law:

:$U_e = int \left\{k x\right\}, dx = frac \left\{1\right\} \left\{2\right\} k x^2.$

Relation among elastic constants

For homogeneous isotropic materials simple relations exist between elastic constants (Young's modulus "E", shear modulus "G", bulk modulus "K", and Poisson's ratio "ν") that allow calculating them all as long as two are known::$E = 2G\left(1+ u\right) = 3K\left(1-2 u\right).,$

Approximate values

Young's modulus can vary somewhat due to differences in sample composition and test method. The rate of deformation has the greatest impact on the data collected, especially in polymers. The values here are approximate and only meant for relative comparisons.

[
[http://www.glassproperties.com/young_modulus/ Glassproperties.com] ] ).]

* Deflection
* Deformation
* Hardness
* Hooke's law
* Shear modulus
* Impulse excitation technique
* Strain
* Stress
* Toughness
* Yield (engineering)
* List of materials properties

References

* [http://www.matweb.com Matweb: free database of engineering properties for over 63,000 materials]

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• Young's modulus — Modulus Mod u*lus, n.; pl. {Moduli}. [L., a small measure. See {Module}, n.] (Math., Mech., & Physics) A quantity or coefficient, or constant, which expresses the measure of some specified force, property, or quality, as of elasticity, strength,… …   The Collaborative International Dictionary of English

• Young's modulus — Young s modulus. См. Модуль Юнга. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

• Young's modulus — yəŋz n the ratio of the tensile stress in a material to the corresponding tensile strain …   Medical dictionary

• Young's modulus — Physics. a coefficient of elasticity of a substance, expressing the ratio between a stress that acts to change the length of a body and the fractional change in length caused by this force. [1860 65; named after Thomas YOUNG, who derived it] * *… …   Universalium

• Young’s modulus — tampros modulis statusas T sritis Standartizacija ir metrologija apibrėžtis Statmenojo įtempio ir santykinės ilginės deformacijos dalmuo, t. y. E = σ/ε; čia σ – statmenasis įtempis, ε – santykinė ilginė deformacija. atitikmenys: angl. coefficient …   Penkiakalbis aiškinamasis metrologijos terminų žodynas

• Young's modulus — /jʌŋz ˈmɒdʒələs/ (say yungz mojuhluhs) noun the modulus of elasticity of a material in tension or compression, equal to the ratio of the stress applied to a wire or rod of the material to the longitudinal strain produced. {named after Thomas… …   Australian English dictionary

• Young's modulus — noun a coefficient of elasticity applicable to the stretching of a wire • Hypernyms: ↑coefficient of elasticity, ↑modulus of elasticity, ↑elastic modulus …   Useful english dictionary

• Young's modulus — noun The coefficient of elasticity of a solid; the rate of change of stress with strain. Syn: modulus of elasticity …   Wiktionary

• Young's modulus — noun Physics a measure of elasticity, equal to the ratio of the stress acting on a substance to the strain produced. Origin C19: named after the English physicist Thomas Young …   English new terms dictionary

• Modulus Guitars — is an American manufacturer of musical instruments, most notably bass guitars built with carbon fiber necks. The company, originally called Modulus Graphite, was founded in part by Geoff Gould, a bassist who also worked for an aerospace company… …   Wikipedia