- 1 Photoresist categories
- 2 Other aspects of photoresist technologies
- 3 Negative photoresist
- 4 Some common photoresists
- 5 References
- 6 External links
The main properties characterizing the photoresist types are:
Photoresists are classified into two groups: positive resists and negative resists.
- A positive resist is a type of photoresist in which the portion of the photoresist that is exposed to light becomes soluble to the photoresist developer. The portion of the photoresist that is unexposed remains insoluble to the photoresist developer.
- A negative resist is a type of photoresist in which the portion of the photoresist that is exposed to light becomes insoluble to the photoresist developer. The unexposed portion of the photoresist is dissolved by the photoresist developer.
Differences between tone types
Characteristic Positive Negative Adhesion to Silicon Fair Excellent Relative Cost More Expensive Less Expensive Developer Base Aqueous Organic Minimum Feature 0.5 μm and below ± 2 μm Step Coverage Better Lower Wet Chemical Resistance Fair Excellent
Note: This table is based on generalizations which are generally accepted in the MEMS fabrication industry.
Developing light wavelength
This particular parameter is closely related to the thickness of the applied photoresist, with thinner layers corresponding to shorter wavelengths, permitting a reduced aspect ratio and a reduced minimum feature size. This is important in microelectronics and especially the ITRS reduction in minimum feature size. Intel has semiconductor fabrication facilities currently operating at the 32 nanometer node.
Different chemicals may be used for permanently giving the material the desired property variations:
- Poly(methyl methacrylate) (PMMA),
- Poly(methyl glutarimide) (PMGI)
- Phenol formaldehyde resin (DNQ/Novolac),
The above materials are all applied as a liquid and, generally, spin-coated to ensure uniformity of thickness.
- Dry film – stands alone amongst the other types in that the coating already exists as a uniform thickness, semi-solid film coated onto a polyester substrate and the user applies that substrate to the workpiece in question by lamination.
- Fabrication of printed circuit boards. A common application includes applying photoresist, exposing to the image, followed by an etch step using iron chloride, cupric chloride or an alkaline ammonia etching solution to remove the copperclad substrate.
- Sand carving. Sand blasting materials after a photolithographically printed pattern has been applied as a mask.
- Microelectronics – mainly silicon wafers/silicon integrated circuits. This application is the most developed of the technologies and the most specialized in the field.
- Patterning and etching of substrates. This includes specialty photonics materials, MEMS, glass printed circuit boards, and other micropatterning tasks.
Other aspects of photoresist technologies
Absorption at UV and shorter wavelengths
Photoresists are most commonly used at wavelengths in the ultraviolet spectrum or shorter (<400 nm). For example, diazonaphthoquinone (DNQ) absorbs strongly from approximately 300 nm to 450 nm. The absorption bands can be assigned to n-π* (S0–S1) and π-π* (S1–S2) transitions in the DNQ molecule. In the deep ultraviolet (DUV) spectrum, the π-π* electronic transition in benzene  or carbon double-bond chromophores  appears at around 200 nm. Due to the appearance of more possible absorption transitions involving larger energy differences, the absorption tends to increase with shorter wavelength, or larger photon energy. Photons with energies exceeding the ionization potential of the photoresist (can be as low as 5 eV in condensed solutions) can also release electrons which are capable of additional exposure of the photoresist. From about 5 eV to about 20 eV, photoionization of outer "valence band" electrons is the main absorption mechanism. Above 20 eV, inner electron ionization and Auger transitions become more important. Photon absorption begins to decrease as the X-ray region is approached, as fewer Auger transitions between deep atomic levels are allowed for the higher photon energy. The absorbed energy can drive further reactions and ultimately dissipates as heat. This is associated with the outgassing and contamination from the photoresist.
Photoresists can also be exposed by electron beams, producing the same results as exposure by light. The main difference is that while photons are absorbed, depositing all their energy at once, electrons deposit their energy gradually, and scatter within the photoresist during this process. As with high-energy wavelengths, many transitions are excited by electron beams, and heating and outgassing are still a concern. The dissociation energy for a C-C bond is 3.6 eV. Secondary electrons generated by primary ionizing radiation have energies sufficient to dissociate this bond, causing scission. In addition, the low-energy electrons have a longer photoresist interaction time due to their lower speed; essentially the electron has to be at rest with respect to the molecule in order to react most strongly via dissociative electron attachment, where the electron comes to rest at the molecule, depositing all its kinetic energy. The resulting scission breaks the original polymer into segments of lower molecular weight, which are more readily dissolved in a solvent, or else releases other chemical species (acids) which catalyze further scission reactions (see the discussion on chemically amplified resists below).
It is not common to select photoresists for electron-beam exposure. Electron beam lithography usually relies on resists dedicated specifically to electron-beam exposure.
One very common positive photoresist used with the I, G and H-lines from a mercury-vapor lamp is based on a mixture of diazonaphthoquinone (DNQ) and novolac resin (a phenol formaldehyde resin). DNQ inhibits the dissolution of the novolac resin, but upon exposure to light, the dissolution rate increases even beyond that of pure novolac. The mechanism by which unexposed DNQ inhibits novolac dissolution is not well understood, but is believed to be related to hydrogen bonding (or more exactly diazocoupling in the unexposed region). DNQ-novolac resists are developed by dissolution in a basic solution (usually 0.26N tetramethylammonium hydroxide (TMAH) in water).
Contrary to past types, current negative photoresists tend to exhibit better adhesion to various substrates such as Si, GaAs, InP and glass, as well as metals, including Au, Cu and Al, compared to positive-tone photoresists. Additionally, the current generation of G, H and I-line negative-tone photoresists exhibit higher temperature resistance over positive resists.
One very common negative photoresist is based on epoxy-based polymer. The common product name is SU-8 photoresist, and it was originally invented by IBM, but is now sold by Microchem and Gersteltec. One unique property of SU-8 is that it is very difficult to strip. As such, it is often used in applications where a permanent resist pattern (one that is not strippable, and can even be used in harsh temperature and pressure environments) is needed for a device.
Deep Ultraviolet (DUV) resist are typically polyhydroxystyrene-based polymers with a photoacid generator providing the solubility change. However, this material does not experience the diazocoupling. The combined benzene-chromophore and DNQ-novolac absorption mechanisms lead to stronger absorption by DNQ-novolac photoresists in the DUV, requiring a much larger amount of light for sufficient exposure. The strong DUV absorption results in diminished photoresist sensitivity.
Photoresists used in production for DUV and shorter wavelengths require the use of chemical amplification to increase the sensitivity to the exposure energy. This is done in order to combat the larger absorption at shorter wavelengths. Chemical amplification is also often used in electron-beam exposures to increase the sensitivity to the exposure dose. In the process, acids released by the exposure radiation diffuse during the post-exposure bake step. These acids render surrounding polymer soluble in developer. A single acid molecule can catalyze many such 'deprotection' reactions; hence, fewer photons or electrons are needed. Acid diffusion is important not only to increase photoresist sensitivity and throughput, but also to limit line edge roughness due to shot noise statistics. However, the acid diffusion length is itself a potential resolution limiter. In addition, too much diffusion reduces chemical contrast, leading again to more roughness.
The following reactions are an example of commercial chemically amplified photoresists in use today:
- photoacid generator + hν (193 nm) → acid cation + sulfonate anion 
- sulfonate anion + hν (193 nm) → e− + sulfonate
- e− + photoacid generator → e− + acid cation + sulfonate anion 
The e− represents a solvated electron, or a freed electron that may react with other constituents of the solution. It typically travels a distance on the order of many nanometers before being contained; such a large travel distance is consistent with the release of electrons through thick oxide in UV EPROM in response to ultraviolet light. This parasitic exposure would degrade the resolution of the photoresist; for 193 nm the optical resolution is the limiting factor anyway, but for electron beam lithography or EUVL it is the electron range that determines the resolution rather than the optics.
Some common photoresists
Dan Daly states that Shipley, acquired by Rohm and Haas, and Hoechst, now called AZ Electronic Materials, are two producers of microelectronic chemicals. Common products include Hoechst AZ 4620, Hoechst AZ 4562, Shipley 1400-17, Shipley 1400-27, Shipley 1400-37, and Shipley Microposit Developer. The resists mentioned are, generally, applied in a relatively thick layer—approximately 120 nm to 10 µm—and are used in the manufacture of microlens arrays. Microelectronic resists, presumably, utilize specialized products depending upon process objectives and design constraints. The general mechanism of exposure for these photoresists proceeds with the decomposition of diazoquinone, i.e. the evolution of nitrogen gas and the production of carbenes.
- ^ Madou, Marc (2002). Fundamentals of Microfabrication. Boca Raton, Florida: CRC Press. pp. 9. ISBN 0-8493-0826-7.
- ^ DNQ-novolac photoresists
- ^ Ishii, Hiroyuki; Usui, Shinji; Douki, Katsuji; Kajita, Toru; Chawanya, Hitoshi; Shimokawa, Tsutomu. "Design and lithographic performances of 193-specific photoacid generators". Proc. SPIE 3999: 1120. http://www.jsrmicro.com/download/2000SPIEpaperPAG.pdf.
- ^ "UV-Visible Spectroscopy". Cem.msu.edu. http://www.cem.msu.edu/~reusch/VirtualText/Spectrpy/UV-Vis/spectrum.htm. Retrieved 2010-02-26.
- ^ Belbruno, Joseph J.; Siuzdak, Gary; North, Simon (1990). "Multiphoton-induced chemistry of phenol in hexane at 266 nm". Chemical Physics Letters 166: 167. Bibcode 1990CPL...166..167B. doi:10.1016/0009-2614(90)87271-R.
- ^ Weingartner, Joseph C.; Draine, B. T.; Barr, David K. (2006). "Photoelectric Emission from Dust Grains Exposed to Extreme Ultraviolet and X‐Ray Radiation". The Astrophysical Journal 645: 1188. arXiv:astro-ph/0601296. Bibcode 2006ApJ...645.1188W. doi:10.1086/504420.
- ^ Braun, M; Gruber, F; Ruf, M; Kumar, S; Illenberger, E; Hotop, H (2006). "IR photon enhanced dissociative electron attachment to SF6: Dependence on photon, vibrational, and electron energy". Chemical Physics 329: 148. Bibcode 2006CP....329..148B. doi:10.1016/j.chemphys.2006.07.005.
- ^ Greener, Jesse; Li, Wei; Ren, Judy; Voicu, Dan; Pakharenko, Viktoriya; Tang, Tian; Kumacheva, Eugenia (2010). "Rapid, cost-efficient fabrication of microfluidic reactors in thermoplastic polymers by combining photolithography and hot embossing". Lab on a Chip 10 (4): 522. doi:10.1039/b918834g. PMID 20126695.
- ^ U.S. Patent 4,491,628 "Positive and Negative Working Resist Compositions with Acid-Generating Photoinitiator and Polymer with Acid-Labile Groups Pendant From Polymer Backbone" J.M.J. Fréchet, H. Ito and C.G. Willson 1985.
- ^ a b Van Steenwinckel, David; Lammers, Jeroen H.; Koehler, Thomas; Brainard, Robert L.; Trefonas, Peter (2006). "Resist effects at small pitches". Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures 24: 316. Bibcode 2006JVSTB..24..316V. doi:10.1116/1.2151912.
- ^ a b S. Tagawa et al. (2000). "Radiation and photochemistry of onium salt acid generators in chemically amplified resists". Proc. SPIE 3999: 204. doi:10.1117/12.388304.
- ^ Wang, Xue-Bin; Ferris, Kim; Wang, Lai-Sheng (2000). "Photodetachment of Gaseous Multiply Charged Anions, Copper Phthalocyanine Tetrasulfonate Tetraanion: Tuning Molecular Electronic Energy Levels by Charging and Negative Electron Binding". The Journal of Physical Chemistry A 104: 25. doi:10.1021/jp9930090.
- ^ Lu, Hong; Long, Frederick H.; Eisenthal, K. B. (1990). "Femtosecond studies of electrons in liquids". Journal of the Optical Society of America B 7: 1511. Bibcode 1990JOSAB...7.1511L. doi:10.1364/JOSAB.7.001511.
- ^ Lukin, L (2001). "Thermalization of low energy electrons in liquid methylcyclohexane studied by the photoassisted ion pair separation technique". Chemical Physics 265: 87. Bibcode 2001CP....265...87L. doi:10.1016/S0301-0104(01)00260-9.
Wikimedia Foundation. 2010.
Look at other dictionaries:
photoresist — [fōt΄ō ri zist′] n. a substance that can be made to form a tough film by a photographic process, used to mask electrical circuits before chemical etching … English World dictionary
Photoresist — Résine photosensible La résine photosensible (appelée aussi photorésine et parfois photorésist) est un matériau photosensible utilisé dans de nombreux procédés industriels, comme la photolithographie ou la photogravure afin de former un… … Wikipédia en Français
Photorésist — Résine photosensible La résine photosensible (appelée aussi photorésine et parfois photorésist) est un matériau photosensible utilisé dans de nombreux procédés industriels, comme la photolithographie ou la photogravure afin de former un… … Wikipédia en Français
photoresist — fotorezistas statusas T sritis radioelektronika atitikmenys: angl. optical resist; photoresist; photosensitive lacquer vok. Fotolack, m; Fotoresist, n rus. фоторезист, m pranc. photorésist, m; résine photosensible, f … Radioelektronikos terminų žodynas
photorésist — fotorezistas statusas T sritis radioelektronika atitikmenys: angl. optical resist; photoresist; photosensitive lacquer vok. Fotolack, m; Fotoresist, n rus. фоторезист, m pranc. photorésist, m; résine photosensible, f … Radioelektronikos terminų žodynas
Photoresist — Fotolacke (engl. Photoresist) werden insbesondere in der Mikroelektronik und der Mikrosystemtechnik für die Produktion von Strukturen im Mikro und Submikrometerbereich und bei der Leiterplattenherstellung verwendet. Die wichtigsten Ausgangsstoffe … Deutsch Wikipedia
Photoresist — Pho|to|re|sịst [engl. resist = Abdeckmittel, Überzug], das; s, s; Syn.: Photolack, Photopolymer (2): bei der Herst. von Druckplatten oder elektronischen Bausteinen benutztes Beschichtungsmittel, das bei Einwirkung insbes. von UV Strahlung… … Universal-Lexikon
photoresist — fotorezistas statusas T sritis chemija apibrėžtis Elektromagnetinei spinduliuotei jautri fotolitografinė medžiaga. atitikmenys: angl. photoresist rus. фоторезист … Chemijos terminų aiškinamasis žodynas
photoresist — noun Date: 1953 a photosensitive resin that loses its resistance to chemical etching when exposed to radiation and is used especially in the transference of a circuit pattern to a semiconductor chip during the production of an integrated circuit … New Collegiate Dictionary
photoresist — /foh toh ri zist /, n. Electronics. a photosensitive liquid polymer, used in photolithography to produce integrated circuits. [1950 55; PHOTO + RESIST] * * * … Universalium