Cutoff (steam engine)

Cutoff (steam engine)

In a steam engine, cutoff is the point in the piston stroke at which the inlet valve is closed. On a steam locomotive, the cutoff is controlled by the reverser.

The point at which the inlet valve closes and stops the entry of steam into the cylinder from the boiler plays a crucial role in the control of a steam engine. Once the valve has closed, steam trapped in the cylinder expands adiabatically. The steam pressure drops as it expands. A late cutoff delivers full steam pressure to move the piston through its entire stroke, for maximum start-up forces. But, since there will still be unexploited pressure in the cylinder at the end of the stroke, this is achieved at the expense of engine efficiency. In this situation the steam will still have considerable pressure remaining when it is exhausted resulting in the characteristic “chuff chuff” sound of a steam engine. An early cutoff has greater thermodynamic efficiency but provides less average force on the piston and is used for running the engine at higher speeds. The steam engine is the only thermodynamic engine design that can provide its maximum torque at zero revolutions.

Contents

Explanation

Schematic Indicator diagram of pressure in a steam locomotive cylinder. The pressure in the cylinder declines after cutoff as the steam pushes the piston down its bore

Cutoff is one of the four valve events. Early cutoff is used to increase the efficiency of the engine by allowing the steam to expand for the rest of the power stroke, yielding more of its energy and conserving steam. This is known as expansive working. Late cutoff is used to provide maximum torque to the shaft at the expense of efficiency and is used to start the engine under load.

Cutoff is conventionally expressed as percentage of the power stroke of the piston; if the piston is at a quarter of its stroke at the cutoff point, the cutoff is stated as 25%.

Smaller stationary steam engines generally have a fixed cutoff point while, in large ones, the speed and power output is generally governed by altering the cutoff, frequently under governor control using an expansion valve or trip gear. In steam engines for transport, it is desirable to be able to alter the cutoff over a wide range. For starting and at low speed and heavy load, the cylinders need steam supply at maximum pressure for almost the full length of the stroke. In a two-cylinder locomotive, for example, the maximum or 'full gear' cutoff is typically about 85%. At high speeds, the cutoff may be 15% percent of the piston stroke or less. Steam engines used in boats and ships operate under a constant, unvarying load through the propeller and so have a fixed cutoff, with speed being controlled through the regulator.[citation needed]

Providing variable cutoff is an important function of the valve gear. Most valve gear designs provide it, the exception being early Stephenson valve gear.

Control mechanism on locomotives

Reversing lever

This is the most common form of reverser. It consists of a long lever mounted, parallel to the direction of travel, on the driver’s side of the cab. It has a handle and sprung trigger at the top and is pivoted at the bottom so as to pass between two notched sector plates. The reversing rod, which connects to the valve gear, is attached to this lever, either above or below the pivot, in such a position as to give good leverage. A square pin is arranged so as to engage with the notches in the plates and hold the lever in the desired position when the trigger is released.

The advantages of this design are that change between forward and reverse gear can be made very quickly as is needed in, for example, a shunting engine. Disadvantages are that, because the lever must rest at one of the notches, fine adjustment of the cutoff to offer best running and economy is not possible. On large locomotives it can be difficult to prevent the mechanism from jumping into full forward gear (“nose-diving”) when adjusting the cutoff once the locomotive has gathered speed: with such engines it was the practice of drivers to select an appropriate degree of cutoff before opening the regulator and to leave it in that position for the duration of the journey.

Screw reverser

Diagram of Stephenson valve gear controlled by a screw reverser

In this mechanism the reversing rod is controlled by a screw and nut, worked by a wheel in the cab. The nut either operates on the reversing rod directly or through a lever, as above. The screw and nut may be cut with a double thread and a coarse pitch to move the mechanism as quickly as possible. The wheel is fitted with a locking lever to prevent creep and there is an indicator to show the percentage of cutoff in use. This method of altering the cutoff offers finer control than the sector lever, but it has the disadvantage of slow operation. It is most suitable for long-distance passenger engines where frequent changes of cutoff are not required and where fine adjustments offer the most benefit. On locomotives fitted with Westinghouse air brake equipment and Stephenson valve gear, it was common to use the screw housing as an air cylinder, with the nut extended to form a piston. Compressed air from the brake reservoirs was applied to one side of the piston to reduce the effort required to lift the heavy expansion link, with gravity assisting in the opposite direction.[1]

The two pistons of the steam reverser can be seen at the extreme left on this Bulleid Merchant Navy class

Power reverse gear

With larger engines, the linkages involved in controlling cutoff and direction grew progressively heavier and there was a need for power assistance in adjusting them. Steam (or later, compressed air) powered reversing gear was developed in the late 19th and early 20th centuries. Typically, the operator worked a valve that admitted steam to one side or the other of a cylinder connected to the reversing mechanism until the indicator showed the intended position. A second mechanism, usually a piston in an oil-filled cylinder held in position by closing a control cock, was required to keep the linkages in place. The first locomotive engineer to fit such a device was James Stirling of the Glasgow and South Western Railway in 1873.[2] Several engineers then tried them, including William Dean of the GWR and Vincent Raven of the North Eastern Railway, but they found them little to their liking, mainly because of maintenance difficulties: any oil leakage from the locking cylinder, either through the piston gland or the cock, allowed the mechanism to creep, or worse “nose-dive”, into full forward gear while running. Stirling moved to the South Eastern Railway and Harry Smith Wainwright, his successor with that company, incorporated them into most of his designs, which were in production about thirty years after Stirling’s innovation. Later still the forward-looking Southern Railway engineer Oliver Bulleid fitted them to his famous Merchant Navy Class of locomotives, but they were mostly removed at rebuild.

Henszey's reversing gear, patented in 1882, illustrates a typical early solution.[3] Henszey's device consists of two pistons mounted on a single piston rod. Both pistons are double-ended. One is a steam piston to move the rod as required. The other, containing oil, holds the rod in a fixed position when the steam is turned off. Control is by a small three-way steam valve (“forward”, “stop”, “back”) and a separate indicator showing the position of the rod and thus the percentage of cutoff in use. When the steam valve is at “stop”, an oil cock connecting the two ends of the locking piston is also closed, thus holding the mechanism in position. The piston rod connects by levers to the reversing gear, which operates in the usual way, according to the type of valve gear in use.

Steam reverser on a Southern Railway 2-8-0.

The Ragonnet power reverse, patented in 1909, was a true feedback controlled servomechanism. The power reverse amplified small motions of reversing lever in the locomotive cab made with modest force into much larger and more forceful motions of the reach rod that controlled the engine cutoff and direction.[4] It was usually air powered, but could also be steam powered.[5] The term servomotor was explicitly used by the developers of some later power reverse mechanisms.[6] The use of feedback control in these later power reverse mechanisms eliminated the need for a second cylinder for a hydraulic locking mechanism, and it restored the simplicity of a single operating lever that both controlled the reversing linkage and indicated its position.

The development of articulated locomotives was a major impetus to the development of power reverse systems, because these typically had two or even three sets of reverse gear, instead of just one on a simple locomotive.[7][8] The Baldwin Locomotive Works used the Ragonnet reversing gear, and other American builders generally abandoned positive locking features. In British use, locking cylinders remained in use. The Hadfield reversing gear, patented in 1950, was in most particulars a Ragonnet reversing gear with added locking cylinder.[9] Most Beyer Garratt locomotives used the Hadfield system. [10]

Many American locomotives were built, or retro-fitted, with power reverse, e.g. PRR K4s, PRR N1s, PRR B6, PRR L1s.

Enginemen’s terminology

In the UK, a screw reverser is sometimes called a “bacon slicer”, particularly the type fitted to BR Standard locomotives. In the US, a reversing lever is called a “Johnson bar”.

References

  1. ^ Railway Gazette (Sutton, England) 86: 638. January 1946. 
  2. ^ Canestrari, Guido; Greggio, Luciano (1985). Steam locomotives. Avenel, New Jersey: Crescent books. p. 105. ISBN 0-517-48366-1. 
  3. ^ William P. Henszey, Reversing-Gear for Locomotives, U.S. Patent 259,538, June 13, 1882.
  4. ^ Eugine L. Ragonnet, Controlling Mechanism for Locomotives, U.S. Patent 930,225, Aug. 9, 1909.
  5. ^ Jacob H Yoder, Locomotive Valves and Valve Gears, [1], Van Nostrand, New York, 1917; page 131.
  6. ^ Lincoln A. Lang, Servo Motor Mechanism, U.S. Patent 1,480,940, Jan 15, 1924.
  7. ^ George R. Henderson, Recent Locomotive Development, Paper 90,Transactions of the International Engineering Congress -- Railway Engineering, San Francisco, Sept. 20-25, 1915; page 491.
  8. ^ Charles McShane, Locomotive Power Reverse Gears,The Locomotive Up to Date, Griffin & Winters, 1921; 413.
  9. ^ James Hadfield, Hydraulic Locking Cylinder for Locomotive Reversing Gear, U.S. Patent 2,523,696, Sept. 26, 1950 (Oct. 7, 1944 in Great Britain).
  10. ^ Ransome-Wallis, Patrick (2001). Illustrated Encyclopedia of World Railway Locomotives. Mineola, NY: Dover Books. p. 278. ISBN 0486412474. 

Sources

  • Allen, Cecil J (1949). Locomotive Practice and Performance in the Twentieth Century.. W.Heffer and Sons Ltd, Cambridge.
  • Bell, A. Morton (1950). Locomotives volume one. Seventh edition. London, Virtue and Company Ltd.

Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • Steam engine — A steam engine is a heat engine that performs mechanical work using steam as its working fluid. [ [http://www.britannica.com/EBchecked/topic/564472/steam engine steam engine Britannica Online Encyclopedia ] ] Steam engines have a long history,… …   Wikipedia

  • Corliss steam engine — A Corliss steam engine – the valve gear is on the right of the cylinder block, on the left of the picture A Corliss steam engine (or Corliss engine) is a steam engine, fitted with rotary valves and with variable valve timing patented in 1849 …   Wikipedia

  • Cutoff — or cut off or cut off may refer to: Contents 1 Science and technology 2 Clothing and fashion 3 Roads and trails …   Wikipedia

  • Cutoff (disambiguation) — Cutoff may refer to: * Cutoff, a range of values to be considered in physics. * Cutoff (steam engine), the point in the piston stroke at which the inlet valve is closed. * Cutoff (metalworking), a piercing operation used to cut a workpiece from… …   Wikipedia

  • cutoff — [kut′ôf΄] n. 1. the act of cutting off; esp., the limit or ending set for a process, activity, etc. 2. a road or passage that cuts across, shortening the distance 3. ☆ a) a new and shorter channel cut by a river across a bend, or dug out to… …   English World dictionary

  • cutoff — /kut awf , of /, n. 1. an act or instance of cutting off. 2. something that cuts off. 3. a road, passage, etc., that leaves another, usually providing a shortcut: Let s take the cutoff to Baltimore. 4. a new and shorter channel formed in a river… …   Universalium

  • cutoff — cut•off [[t]ˈkʌtˌɔf, ˌɒf[/t]] n. 1) an act or instance of cutting off 2) something that cuts off 3) a point serving as the limit beyond which something is no longer effective, applicable, or possible 4) a road, passage, etc., that leaves another …   From formal English to slang

  • Old Bess (beam engine) — Old Bess, as now preserved in the Science Museum, London Old Bess is an early beam engine built by the partnership of Boulton and Watt. The engine was constructed in 1777 and worked until 1848.[1] …   Wikipedia

  • Henry the Green Engine — is a fictional anthropomorphic 4 6 0 steam locomotive from The Railway Series books written by the Reverend Wilbert Vere Awdry and his son, Christopher Awdry, and the spin off children s television series, Thomas the Tank Engine and Friends .… …   Wikipedia

  • Timeline of steam power — See Steam engine, Steam power during the Industrial Revolution. Steam power developed slowly over a period of several hundred years, progressing through expensive and fairly limited devices in the early 1600s, to useful pumps for mining in 1700,… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”