Carry look-ahead adder

Carry look-ahead adder

A carry look-ahead adder is a type of adder used in digital logic. It can be contrasted with the simpler, but usually slower, "ripple carry adder" ("see adder for detail on ripple carry adders").

A ripple-carry adder works in the same way as pencil-and-paper methods of addition. Starting at the rightmost (least significant) digit position, the two corresponding digits are added and a result obtained. It is also possible that there may be a carry out of this digit position (for example, in pencil-and-paper methods, "9+5=4, carry 1"). Accordingly all digit positions other than the rightmost need to take into account the possibility of having to add an extra 1, from a carry that has come in from the next position to the right.

This means that no digit position can have an absolutely final value until it has been established whether or not a carry is coming in from the right. Moreover, if the sum without a carry is 9 (in pencil-and-paper methods) or 1 (in binary arithmetic), it is not even possible to tell whether or not a given digit position is going to pass on a carry to the position on its left. At worst, when a whole sequence of sums comes to ...99999999... (in decimal) or ...11111111... (in binary), nothing can be deduced at all until the value of the carry coming in from the right is known, and that carry is then propagated to the left, one step at a time, as each digit position evaluated "9+1=0, carry 1" or "1+1=0, carry 1". It is the "rippling" of the carry from right to left that gives a ripple-carry adder its name, and its slowness. When adding 32-bit integers, for instance, allowance has to be made for the possibility that a carry could have to ripple through every one of the 32 one-bit adders.

Carry lookahead depends on two things:

  1. Calculating, for each digit position, whether that position is going to propagate a carry if one comes in from the right.
  2. Combining these calculated values so as to be able to deduce quickly whether, for each group of digits, that group is going to propagate a carry that comes in from the right.

Supposing that groups of 4 digits are chosen. Then the sequence of events goes something like this:

  1. All 1-bit adders calculate their results. Simultaneously, the lookahead units perform their calculations.
  2. Suppose that a carry arises in a particular group. Within at most 3 gate delays, that carry will emerge at the left-hand end of the group and start propagating through the group to its left.
  3. If that carry is going to propagate all the way through the next group, the lookahead unit will already have deduced this. Accordingly, "before the carry emerges from the next group" the lookahead unit is immediately (within 1 gate delay) able to tell the "next" group to the left that it is going to receive a carry - and, at the same time, to tell the next lookahead unit to the left that a carry is on its way.

The net effect is that the carries start by propagating slowly through each 4-bit group, just as in a ripple-carry system, but then move 4 times as fast, leaping from one lookahead carry unit to the next. Finally, within each group that receives a carry, the carry propagates slowly within the digits in that group.

The more bits in a group, the more complex the lookahead carry logic becomes, and the more time is spent on the "slow roads" in each group rather than on the "fast road" between the groups (provided by the lookahead carry logic). On the other hand, the fewer bits there are in a group, the more groups have to be traversed to get from one end of a number to the other, and the less acceleration is obtained as a result.

Deciding the group size to be governed by lookahead carry logic requires a detailed analysis of gate and propagation delays for the particular technology being used.

It is possible to have more than one level of lookahead carry logic, and this is in fact usually done. Each lookahead carry unit already produces a signal saying "if a carry comes in from the right, I will propagate it to the left", and those signals can be combined so that each group of (let us say) four lookahead carry units becomes part of a "supergroup" governing a total of 16 bits of the numbers being added. The "supergroup" lookahead carry logic will be able to say whether a carry entering the supergroup will be propagated all the way through it, and using this information, it is able to propagate carries from right to left 16 times as fast as a naive ripple carry. With this kind of two-level implementation, a carry may first propagate through the "slow road" of individual adders, then, on reaching the left-hand end of its group, propagate through the "fast road" of 4-bit lookahead carry logic, then, on reaching the left-hand end of its supergroup, propagate through the "superfast road" of 16-bit lookahead carry logic.

Again, the group sizes to be chosen depend on the exact details of how fast signals propagate within logic gates and from one logic gate to another.

For very large numbers (hundreds or even thousands of bits) lookahead carry logic does not become any more complex, because more layers of supergroups and supersupergroups can be added as necessary. The increase in the number of gates is also moderate: if all the group sizes are 4, one would end up with one third as many lookahead carry units as there are adders. However, the "slow roads" on the way to the faster levels begin to impose a drag on the whole system (for instance, a 256-bit adder could have up to 24 gate delays in its carry processing), and the mere physical transmission of signals from one end of a long number to the other begins to be a problem. At these sizes carry-save adders are preferable, since they spend no time on carry propagation at all.

Carry lookahead method

Carry lookahead logic uses the concepts of "generating" and "propagating" carries. Although in the context of a carry lookahead adder, it is most natural to think of generating and propagating in the context of binary addition, the concepts can be used more generally than this. In the descriptions below, the word "digit" can be replaced by "bit" when referring to binary addition.

The addition of two 1-digit inputs A and B is said to "generate" if the addition will always carry, regardless of whether there is an input carry (equivalently, regardless of whether any less significant digits in the sum carry). For example, in the decimal addition 52 + 67, the addition of the tens digits 5 and 6 "generates" because the result carries to the hundreds digit regardless of whether the ones digit carries (in the example, the ones digit does not carry (2+7=9)).

In the case of binary addition, A + B generates if and only if both A and B are 1. If we write G(A,B) to represent the binary predicate that is true if and only if A + B generates, we have:

:G(A,B) = A cdot B

The addition of two 1-digit inputs A and B is said to "propagate" if the addition will carry whenever there is an input carry (equivalently, when the next less significant digit in the sum carries). For example, in the decimal addition 37 + 62, the addition of the tens digits 3 and 6 "propagate" because the result would carry to the hundreds digit "if" the ones were to carry (which in this example, it does not). Note that propagate and generate are defined with respect to a single digit of addition and do not depend on any other digits in the sum.

In the case of binary addition, A + B propagates if and only if at least one of A or B is 1. If we write P(A,B) to represent the binary predicate that is true if and only if A + B propagates, we have:

: P(A,B) = A + B

Sometimes a slightly different definition of "propagate" is used. By this definition A + B is said to propagate if the addition will carry whenever there is an input carry, but will not carry if there is no input carry. It turns out that the way in which generate and propagate bits are used by the carry lookahead logic, it doesn't matter which definition is used. In the case of binary addition, this definition is expressed by:

:P^{prime}(A,B) = A oplus B

For binary arithmetic, "or" is faster than "xor" and takes fewer transistors to implement. However, for a multiple-level carry lookahead adder, it is simpler to use P^{prime}(A,B).

Given these concepts of generate and propagate, when will a digit of addition carry? It will carry precisely when either the addition generates "or" the next less significant bit carries and the addition propagates. Written in boolean algebra, with C_i the carry bit of digit i, and P_i and G_i the propagate and generate bits of digit i respectively,

:C_{i+1} = G_i + left( P_i cdot C_i ight)

Implementation details

For each bit in a binary sequence to be added, the Carry Look Ahead Logic will determine whether that bit pair will generate a carry or propagate a carry. This allows the circuit to "pre-process" the two numbers being added to determine the carry ahead of time. Then, when the actual addition is performed, there is no delay from waiting for the ripple carry effect (or time it takes for the carry from the first Full Adder to be passed down to the last Full Adder). Below is a simple 4-bit generalized Carry Look Ahead circuit that combines with the 4-bit Ripple Carry Adder we used above with some slight adjustments:

For the example provided, the logic for the generate (g) and propagate (p) values are given below. Note that the numeric value determines the signal from the circuit above, starting from 0 on the far left to 3 on the far right:

:C_1 = G_0 + P_0 cdot C_0:C_2 = G_1 + P_1 cdot C_1:C_3 = G_2 + P_2 cdot C_2:C_4 = G_3 + P_3 cdot C_3

Substituting C_1 into C_2, then C_2 into C_3, then C_3 into C_4 yields the expanded equations:

:C_1 = G_0 + P_0 cdot C_0:C_2 = G_1 + G_0 cdot P_1 + C_0 cdot P_0 cdot P_1:C_3 = G_2 + G_1 cdot P_2 + G_0 cdot P_1 cdot P_2 + C_0 cdot P_0 cdot P_1 cdot P_2:C_4 = G_3 + G_2 cdot P_3 + G_1 cdot P_2 cdot P_3 + G_0 cdot P_1 cdot P_2 cdot P_3 + C_0 cdot P_0 cdot P_1 cdot P_2 cdot P_3

To determine whether a bit pair will generate a carry, the following logic works::G_i = A_i cdot B_i

To determine whether a bit pair will propagate a carry, either of the following logic statements work::P_i = A_i oplus B_i: P_i = A_i + B_i

The reason why this works is based on evaluation of C_1 = G_0 + P_0 cdot C_0. The only difference in the truth tables between (A oplus B) and (A + B) is when both A and B are 1. However, if both A and B are 1, then the G_0 term is 1 (since its equation is A cdot B), and the P_0 cdot C_0 term becomes irrelevant. The XOR is used normally within a basic full adder circuit; the OR is an alternate option (for a carry lookahead only) which is far simpler in transistor-count terms.

The Carry Look Ahead 4-bit adder can also be used in a higher-level circuit by having each CLA Logic circuit produce a propagate and generate signal to a higher-level CLA Logic circuit. The group propagate (PG) and group generate (GG) for a 4-bit CLA are::PG = P_0 cdot P_1 cdot P_2 cdot P_3:GG = G_3 + G_2 cdot P_3 + G_1 cdot P_3 cdot P_2 + G_0 cdot P_3 cdot P_2 cdot P_1

Putting 4 4-bit CLAs together yields four group propagates and four group generates.A Lookahead Carry Unit (LCU) takes these 8 values and uses identical logic to calculate C_i in the CLAs.The LCU then generates the carry input for each of the 4 CLAs and a fifth equal to C_{16}.

The calculation of the gate delay of a 16-bit adder (using 4 CLAs and 1 LCU) is not as straight forward as the ripple carry adder.Starting at time of zero:
* calculation of P_i and G_i is done at time 1
* calculation of C_i is done at time 3
* calculation of the PG is done at time 2
* calculation of the GG is done at time 3
* calculation of the inputs for the CLAs from the LCU are done at
** time 0 for the first CLA
** time 5 for the second CLA
** time 5 for the third & fourth CLA
* calculation of the S_i are done at
** time 4 for the first CLA
** time 8 for the second CLA
** time 8 for the third & fourth CLA
* calculation of the final carry bit (C_{16}) is done at time 5

The maximum time is 8 gate delays (for S_{ [8-15] }).A standard 16-bit ripple carry adder would take 31 gate delays.

Manchester carry chain

The Manchester carry chain is a variation of the carry look-ahead adder that uses shared logic to lower the transistor count. As can be seen above in the implementation section, the logic for generating each carry contains all of the logic used to generate the previous carries. A Manchester carry chain generates the intermediate carries by tapping off nodes in the gate that calculates the most significant carry value. Not all logic families have these internal nodes, however, CMOS being a major example. Dynamic logic can support shared logic, as can transmission gate logic. One of the major downsides of the Manchester carry chain is that the capacitive load of all of these outputs, together with the resistance of the transistors causes the propagation delay to increase much quicker than a regular carry look-ahead. A Manchester carry chain section generally won't exceed 4 bits.

ee also

* Full adder
* Carry save adder
* Lookahead Carry Unit

References

* [http://www.aoki.ecei.tohoku.ac.jp/arith/mg/algorithm.html#fsa_rcl Hardware algorithms for arithmetic modules] , ARITH research group, Aoki lab., Tohoku University
*


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Carry-Look-Ahead-Adder — Der Paralleladdierer mit Übertragsvorausberechnung bzw. Carry Look Ahead Addierer (kurz: CLA Addierer) ist ein elektronischer Baustein zur Addition mehrstelliger Binärzahlen (siehe auch Addierwerk). Der CLA Addierer addiert zwei n stellige… …   Deutsch Wikipedia

  • Carry — or carrying may refer to: *Carry (arithmetic), when a digit becomes bigger than limit and the extra is moved to the left **Carry flag, the equivalent in calculation in a computer *Carrying (basketball), a rule breach in basketball *Carry… …   Wikipedia

  • Carry-lookahead adder — 4 bit adder with carry lookahead A carry lookahead adder (CLA) is a type of adder used in digital logic. A carry lookahead adder improves speed by reducing the amount of time required to determine carry bits. It can be contrasted with the simpler …   Wikipedia

  • Carry-save adder — MotivationA carry save adder is a type of digital adder, used in computer microarchitecture to compute the sum of three or more n bit numbers in binary. It differs from other digital adders in that it outputs two numbers of the same dimensions as …   Wikipedia

  • Adder-subtracter — In digital circuits, an adder subtracter is a circuit that is capable of adding or subtracting numbers (in particular, binary).Below is a circuit that does adding or subtracting depending on a control signal.However, it is possible to construct a …   Wikipedia

  • Adder (electronics) — In electronics, an adder or summer is a digital circuit that performs addition of numbers.In modern computers adders reside in the arithmetic logic unit (ALU) where other operations are performed.Although adders can be constructed for many… …   Wikipedia

  • Carry-Bypass-Adder — Das Addiernetz bildet aus den Summanden a3..0 und b3..0 die Summe s3..0, carry in und carry out ermöglichen die Kaskadierung des Schaltnetzes Das Addierwerk ist die Hauptkomponente des Rechenwerks einer CPU. Das Addierwerk ermöglicht die Addition …   Deutsch Wikipedia

  • Lookahead Carry Unit — A Lookahead Carry Unit (LCU) is a logical unit in digital circuit design used to decrease calculation time in adder units and used in conjunction with carry look ahead adders (CLAs).16 bit adderBy combining four 4 bit CLAs, a 16 bit adder can be… …   Wikipedia

  • Kogge-Stone Adder — The Kogge Stone adder is a parallel prefix form carry look ahead adder. It generates the carry signals in O(log n) time, and is widely considered the fastest adder design possible. It is the common design for high performance adders in… …   Wikipedia

  • Ling adder — In electronics, an adder is a combinatorial or sequential logic element which computes the n bit sum of two numbers. The family of Ling adders is a particularly fast adder and is designed using H. Ling s equations and generally implemented in… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”