Sprue (molding)

Sprue (molding)

A sprue is the passage through which molten material is introduced into a mold. During casting or molding, the material in the sprue will solidify and need to be removed from the finished part.

Casting

In casting, a sprue is the passage through which a molten material is introduced into a mold, and the term also refers to the excess material which solidifies in the sprue passage. In sand casting, the sprue is formed by a dowel which is removed from the sand to make the hole into which the metal is poured.

Function

Sprues can serve as filters, heat sinks, and as feeders. Bronze in particular has a high shrinkage rate as it is cooling; a sprue can continue to provide molten metal to the casting, provided it is large enough to retain its heat and stay liquid, as metal in the main casting cools and shrinks. The design of the sprue and runner system can be also utilized to trap unwanted dross and sand from continuing into the main cavity; this may include adding porous material to the runners, or designing the sprue to eject the dross to the side of the sprue (cyclone effect).

prue design

The design of gating and runner is also essential for casting. The design can be done by using vertical and bottom gating.

For bottom gating

:t_f = frac {2 A_m(sqrt {h_t}-sqrt {h_t-h_m})} {A_g sqrt {2g

where:

:t_f = Time for filling

:A_m = Area of mold

:A_g = Area of gate

:g = Gravity

:h_t = Total height

:h_m = Height of mold cavity

This equation may change if the height of gating is equal to height of casting material.

Then the equation will be:

:t_f = frac {2 A_msqrt {h_t-(h_t-h_m) {A_g sqrt {2g

or, simplified,

:t_f = frac {2 A_msqrt {h_m {A_g sqrt {2g

where:

:t_f = Time for filling

:A_m = Area of mold

:A_g = Area of gate

:g = Gravity

:h_t = Total height (Height of gating + height of mold cavity)

:h_m = Height of mold cavity

Injection molding

In injection molding, the term sprue refers to the passages through which a liquid material (such as polystyrene) flows into a die, where it solidifies to form parts. It also refers to the material which solidifies in these passages, forming a framework attaching the parts together in a roughly planar arrangement.

Gates and runners

Some moldmakers make a distinction between three separate entities: the gate, the runner, and the sprue. The gate is the location at which the molten plastic enters the mold, and is often seen as a small nub or projection (the "gate mark") on the outside edge of the molded piece. The runners are large-diameter channels through which plastic flows, usually around the edges of the part or along straight lines. Finally, in this naming scheme, the sprue represents only the smaller channels that divert from the runners to the individual part. An analogy to the runner/sprue system might represent the runners with city water mains, and sprues with the smaller pipes leading to individual houses.

Many scale model kits are made from injection-molded plastic. Hobbyists, such as builders of scale models, typically remove the parts of a model kit from the sprue using a sharp craft knife or razor saw. They may also use the runner as a raw material to fabricate additional parts, such as railings on model ships, or antenna wires on airplanes.

Runners in model kits often include engravings to identify the parts by number.

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • Injection molding — (British: moulding) is a manufacturing process for producing parts from both thermoplastic and thermosetting plastic materials. Molten plastic is injected at high pressure into a mold, which is the inverse of the product s shape. After a product… …   Wikipedia

  • Transfer molding — Transfer molding, like compression molding, is a process where the amount of molding material (usually a thermoset plastic) is measured and inserted before the molding takes place. The molding material is preheated and loaded into a chamber known …   Wikipedia

  • Injection molding of liquid silicone rubber — (LSR) is a process to produce pliable, durable parts in high volume.Liquid silicone rubber is a high purity platinum cured silicone with low compression set, great stability and ability to resist extreme temperatures of heat and cold ideally… …   Wikipedia

  • Sand casting — Sand casting, also known as sand molded casting, is a metal casting process characterized by using sand as the mold material. It is relatively cheap and sufficiently refractory even for steel foundry use. A suitable bonding agent (usually clay)… …   Wikipedia

  • Casting (metalworking) — Casting iron in a sand mold In metalworking, casting involves pouring liquid metal into a mold, which contains a hollow cavity of the desired shape, and then allowing it to cool and solidify. The solidified part is also known as a casting, which… …   Wikipedia

  • Cope and drag — with cores in place on the drag …   Wikipedia

  • Die casting — An engine block with aluminium and magnesium die castings. Die casting is a metal casting process that is characterized by forcing molten metal under high pressure into a mold cavity. The mold cavity is created using two hardened tool steel dies… …   Wikipedia

  • Foundry — A foundry is a factory which produces metal castings from either ferrous or non ferrous alloys. Metals are turned into parts by melting the metal into a liquid, pouring the metal in a mold, and then removing the mold material or casting. The most …   Wikipedia

  • Riser (casting) — Underfeeder redirects here. For the health problem, see Underfeeding. A bronze casting showing the sprue and risers A riser, also known as a feeder,[1] is a reservoir built into a metal casting …   Wikipedia

  • Core (manufacturing) — A core is a device used in casting and molding processes to produce internal cavities and reentrant angles. The core is normally a disposable item that is destroyed to get it out of the piece.[1] They are most commonly used in sand casting, but… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”