Modulation

Modulation
Passband modulation v · d · e
Analog modulation
AM · SSB · QAM · FM · PM · SM
Digital modulation
FSK · MFSK · ASK · OOK · PSK · QAM
MSK · CPM · PPM · TCM · SC-FDE
Spread spectrum
CSS · DSSS · FHSS · THSS
See also: Demodulation, modem,
line coding, PAM, PWM, PCM

In electronics and telecommunications, modulation is the process of varying one or more properties of a high-frequency periodic waveform, called the carrier signal, with a modulating signal which typically contains information to be transmitted. This is done in a similar fashion to a musician modulating a tone (a periodic waveform) from a musical instrument by varying its volume, timing and pitch. The three key parameters of a periodic waveform are its amplitude ("volume"), its phase ("timing") and its frequency ("pitch"). Any of these properties can be modified in accordance with a low frequency signal to obtain the modulated signal. Typically a high-frequency sinusoid waveform is used as carrier signal, but a square wave pulse train may also be used.

In telecommunications, modulation is the process of conveying a message signal, for example a digital bit stream or an analog audio signal, inside another signal that can be physically transmitted. Modulation of a sine waveform is used to transform a baseband message signal into a passband signal, for example low-frequency audio signal into a radio-frequency signal (RF signal). In radio communications, cable TV systems or the public switched telephone network for instance, electrical signals can only be transferred over a limited passband frequency spectrum, with specific (non-zero) lower and upper cutoff frequencies. Modulating a sine-wave carrier makes it possible to keep the frequency content of the transferred signal as close as possible to the centre frequency (typically the carrier frequency) of the passband.

A device that performs modulation is known as a modulator and a device that performs the inverse operation of modulation is known as a demodulator (sometimes detector or demod). A device that can do both operations is a modem (from "modulator–demodulator").

Contents

Aim

The aim of digital modulation is to transfer a digital bit stream over an analog bandpass channel, for example over the public switched telephone network (where a bandpass filter limits the frequency range to between 300 and 3400 Hz), or over a limited radio frequency band.

The aim of analog modulation is to transfer an analog baseband (or lowpass) signal, for example an audio signal or TV signal, over an analog bandpass channel at a different frequency, for example over a limited radio frequency band or a cable TV network channel.

Analog and digital modulation facilitate frequency division multiplexing (FDM), where several low pass information signals are transferred simultaneously over the same shared physical medium, using separate passband channels (several different carrier frequencies).

The aim of digital baseband modulation methods, also known as line coding, is to transfer a digital bit stream over a baseband channel, typically a non-filtered copper wire such as a serial bus or a wired local area network.

The aim of pulse modulation methods is to transfer a narrowband analog signal, for example a phone call over a wideband baseband channel or, in some of the schemes, as a bit stream over another digital transmission system.

In music synthesizers, modulation may be used to synthesise waveforms with an extensive overtone spectrum using a small number of oscillators. In this case the carrier frequency is typically in the same order or much lower than the modulating waveform. See for example frequency modulation synthesis or ring modulation synthesis.

Analog modulation methods

A low-frequency message signal (top) may be carried by an AM or FM radio wave.

In analog modulation, the modulation is applied continuously in response to the analog information signal. Common analog modulation techniques are:[1]

  • Angle modulation
    • Frequency modulation (FM) (here the frequency of the carrier signal is varied in accordance to the instantaneous amplitude of the modulating signal)
    • Phase modulation (PM) (here the phase shift of the carrier signal is varied in accordance to the instantaneous amplitude of the modulating signal)

Digital modulation methods

In digital modulation, an analog carrier signal is modulated by a discrete signal. Digital modulation methods can be considered as digital-to-analog conversion, and the corresponding demodulation or detection as analog-to-digital conversion. The changes in the carrier signal are chosen from a finite number of M alternative symbols (the modulation alphabet).

Schematic of 4 baud (8 bit/s) data link containing arbitraily chosen values.

A simple example: A telephone line is designed for transferring audible sounds, for example tones, and not digital bits (zeros and ones). Computers may however communicate over a telephone line by means of modems, which are representing the digital bits by tones, called symbols. If there are four alternative symbols (corresponding to a musical instrument that can generate four different tones, one at a time), the first symbol may represent the bit sequence 00, the second 01, the third 10 and the fourth 11. If the modem plays a melody consisting of 1000 tones per second, the symbol rate is 1000 symbols/second, or baud. Since each tone (i.e., symbol) represents a message consisting of two digital bits in this example, the bit rate is twice the symbol rate, i.e. 2000 bits per second. This is similar to the technique used by dialup modems as opposed to DSL modems.

.

According to one definition of digital signal, the modulated signal is a digital signal, and according to another definition, the modulation is a form of digital-to-analog conversion. Most textbooks would consider digital modulation schemes as a form of digital transmission, synonymous to data transmission; very few would consider it as analog transmission.

Fundamental digital modulation methods

The most fundamental digital modulation techniques are based on keying:

In QAM, an inphase signal (the I signal, for example a cosine waveform) and a quadrature phase signal (the Q signal, for example a sine wave) are amplitude modulated with a finite number of amplitudes, and summed. It can be seen as a two-channel system, each channel using ASK. The resulting signal is equivalent to a combination of PSK and ASK.

In all of the above methods, each of these phases, frequencies or amplitudes are assigned a unique pattern of binary bits. Usually, each phase, frequency or amplitude encodes an equal number of bits. This number of bits comprises the symbol that is represented by the particular phase, frequency or amplitude.

If the alphabet consists of M = 2N alternative symbols, each symbol represents a message consisting of N bits. If the symbol rate (also known as the baud rate) is fS symbols/second (or baud), the data rate is NfS bit/second.

For example, with an alphabet consisting of 16 alternative symbols, each symbol represents 4 bits. Thus, the data rate is four times the baud rate.

In the case of PSK, ASK or QAM, where the carrier frequency of the modulated signal is constant, the modulation alphabet is often conveniently represented on a constellation diagram, showing the amplitude of the I signal at the x-axis, and the amplitude of the Q signal at the y-axis, for each symbol.

Modulator and detector principles of operation

PSK and ASK, and sometimes also FSK, are often generated and detected using the principle of QAM. The I and Q signals can be combined into a complex-valued signal I+jQ (where j is the imaginary unit). The resulting so called equivalent lowpass signal or equivalent baseband signal is a complex-valued representation of the real-valued modulated physical signal (the so called passband signal or RF signal).

These are the general steps used by the modulator to transmit data:

  1. Group the incoming data bits into codewords, one for each symbol that will be transmitted.
  2. Map the codewords to attributes, for example amplitudes of the I and Q signals (the equivalent low pass signal), or frequency or phase values.
  3. Adapt pulse shaping or some other filtering to limit the bandwidth and form the spectrum of the equivalent low pass signal, typically using digital signal processing.
  4. Perform digital-to-analog conversion (DAC) of the I and Q signals (since today all of the above is normally achieved using digital signal processing, DSP).
  5. Generate a high-frequency sine wave carrier waveform, and perhaps also a cosine quadrature component. Carry out the modulation, for example by multiplying the sine and cosine wave form with the I and Q signals, resulting in that the equivalent low pass signal is frequency shifted into a modulated passband signal or RF signal. Sometimes this is achieved using DSP technology, for example direct digital synthesis using a waveform table, instead of analog signal processing. In that case the above DAC step should be done after this step.
  6. Amplification and analog bandpass filtering to avoid harmonic distortion and periodic spectrum

At the receiver side, the demodulator typically performs:

  1. Bandpass filtering.
  2. Automatic gain control, AGC (to compensate for attenuation, for example fading).
  3. Frequency shifting of the RF signal to the equivalent baseband I and Q signals, or to an intermediate frequency (IF) signal, by multiplying the RF signal with a local oscillator sinewave and cosine wave frequency (see the superheterodyne receiver principle).
  4. Sampling and analog-to-digital conversion (ADC) (Sometimes before or instead of the above point, for example by means of undersampling).
  5. Equalization filtering, for example a matched filter, compensation for multipath propagation, time spreading, phase distortion and frequency selective fading, to avoid intersymbol interference and symbol distortion.
  6. Detection of the amplitudes of the I and Q signals, or the frequency or phase of the IF signal.
  7. Quantization of the amplitudes, frequencies or phases to the nearest allowed symbol values.
  8. Mapping of the quantized amplitudes, frequencies or phases to codewords (bit groups).
  9. Parallel-to-serial conversion of the codewords into a bit stream.
  10. Pass the resultant bit stream on for further processing such as removal of any error-correcting codes.

As is common to all digital communication systems, the design of both the modulator and demodulator must be done simultaneously. Digital modulation schemes are possible because the transmitter-receiver pair have prior knowledge of how data is encoded and represented in the communications system. In all digital communication systems, both the modulator at the transmitter and the demodulator at the receiver are structured so that they perform inverse operations.

Non-coherent modulation methods do not require a receiver reference clock signal that is phase synchronized with the sender carrier wave. In this case, modulation symbols (rather than bits, characters, or data packets) are asynchronously transferred. The opposite is coherent modulation.

List of common digital modulation techniques

The most common digital modulation techniques are:

MSK and GMSK are particular cases of continuous phase modulation. Indeed, MSK is a particular case of the sub-family of CPM known as continuous-phase frequency-shift keying (CPFSK) which is defined by a rectangular frequency pulse (i.e. a linearly increasing phase pulse) of one symbol-time duration (total response signaling).

OFDM is based on the idea of frequency-division multiplexing (FDM), but is utilized as a digital modulation scheme. The bit stream is split into several parallel data streams, each transferred over its own sub-carrier using some conventional digital modulation scheme. The modulated sub-carriers are summed to form an OFDM signal. OFDM is considered as a modulation technique rather than a multiplex technique, since it transfers one bit stream over one communication channel using one sequence of so-called OFDM symbols. OFDM can be extended to multi-user channel access method in the orthogonal frequency-division multiple access (OFDMA) and multi-carrier code division multiple access (MC-CDMA) schemes, allowing several users to share the same physical medium by giving different sub-carriers or spreading codes to different users.

Of the two kinds of RF power amplifier, switching amplifiers (Class C amplifiers) cost less and use less battery power than linear amplifiers of the same output power. However, they only work with relatively constant-amplitude-modulation signals such as angle modulation (FSK or PSK) and CDMA, but not with QAM and OFDM. Nevertheless, even though switching amplifiers are completely unsuitable for normal QAM constellations, often the QAM modulation principle are used to drive switching amplifiers with these FM and other waveforms, and sometimes QAM demodulators are used to receive the signals put out by these switching amplifiers.

Digital baseband modulation or line coding

The term digital baseband modulation (or digital baseband transmission) is synonymous to line codes. These are methods to transfer a digital bit stream over an analog baseband channel (a.k.a. lowpass channel) using a pulse train, i.e. a discrete number of signal levels, by directly modulating the voltage or current on a cable. Common examples are unipolar, non-return-to-zero (NRZ), Manchester and alternate mark inversion (AMI) codings.[2]

Pulse modulation methods

Pulse modulation schemes aim at transferring a narrowband analog signal over an analog baseband channel as a two-level signal by modulating a pulse wave. Some pulse modulation schemes also allow the narrowband analog signal to be transferred as a digital signal (i.e. as a quantized discrete-time signal) with a fixed bit rate, which can be transferred over an underlying digital transmission system, for example some line code. These are not modulation schemes in the conventional sense since they are not channel coding schemes, but should be considered as source coding schemes, and in some cases analog-to-digital conversion techniques.

Analog-over-analog methods:

Analog-over-digital methods:

Miscellaneous modulation techniques

See also

References

  1. ^ Kundu Sudakshina (2010). Analog and Digital Communications. Pearson Education India. pp. 163–184. ISBN 9788131731871. http://books.google.com/books?id=JKfTrRRHT5QC&pg=PA164. 
  2. ^ Ke-Lin Du and M. N. S. Swamy (2010). Wireless Communication Systems: From RF Subsystems to 4G Enabling Technologies. Cambridge University Press. p. 188. ISBN 9780521114035. http://books.google.com/books?id=5dGjKLawsTkC&pg=PA188. 

Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • modulation — [ mɔdylasjɔ̃ ] n. f. • 1495, rare av. 1626; lat. modulatio 1 ♦ Chacun des changements de ton, d accent, d intensité, de hauteur dans l émission d un son (⇒ inflexion). Les modulations du chant de l oiseau. ♢ Action ou façon de moduler. « Cette… …   Encyclopédie Universelle

  • Modulation — Mod u*la tion, n. [L. modulatio: cf. F. modulation.] 1. The act of modulating, or the state of being modulated; as, the modulation of the voice. [1913 Webster] 2. Sound modulated; melody. [R.] Thomson. [1913 Webster] 3. (Mus.) A change of key,… …   The Collaborative International Dictionary of English

  • modulation — (n.) late 14c., act of singing or making music, from O.Fr. modulation act of making music (14c.), or directly from L. modulationem (nom. modulatio) rhythmical measure, singing and playing, melody, noun of action from pp. stem of modulari regulate …   Etymology dictionary

  • modulation — Modulation. s. f. Chant qui varie d un son à autre, suivant certaines notes ou consonances agreables à l oreille. La modulation de cette basse est fort belle …   Dictionnaire de l'Académie française

  • modulation — modulation. См. модуляция. (Источник: «Англо русский толковый словарь генетических терминов». Арефьев В.А., Лисовенко Л.А., Москва: Изд во ВНИРО, 1995 г.) …   Молекулярная биология и генетика. Толковый словарь.

  • Modulation — (v. lat.), der dem Ohre wohlgefällige Übergang aus einer Tonart in eine andere. Man wendet sie an, um theils durch Mannigfaltigkeit den Reiz der Harmonie zu erhöhen, theils um den Hauptgedanken eines Tonstücks (Thema) nicht so oft in seiner… …   Pierer's Universal-Lexikon

  • Modulation — (lat.), in der Musik der Übergang aus einer Tonart in die andre, modern ausgedrückt: Wechsel der Tonalität (s. d.), das Übergehen der Bedeutung des Hauptklanges (Tonika) auf einen andern Klang, also überhaupt der Wechsel der Funktionen der… …   Meyers Großes Konversations-Lexikon

  • Modulation — (lat.), der Übergang von einer Tonart zur andern, der stets durch der Ausgangstonart fremde, d.h. nicht leitereigene Elemente bewirkt wird, dann auch der Tonwechsel in der Melodie und Harmonie; modulieren, aus einer Tonart in die andere… …   Kleines Konversations-Lexikon

  • Modulation — Modulation, die Abwechselung der Töne in einer Melodie; insbesonders der Uebergang aus einer Tonart in die andere, die Abweichung …   Herders Conversations-Lexikon

  • modulation — index inflection, remission Burton s Legal Thesaurus. William C. Burton. 2006 …   Law dictionary

  • Modulation — Modulation,die:⇨Abänderung …   Das Wörterbuch der Synonyme

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”