# Stress intensity factor

﻿
Stress intensity factor

Stress Intensity Factor, K, is used in fracture mechanics to more accurately predict the stress state ("stress intensity") near the tip of a crack caused by a remote load or residual stresses.It is a theoretical construct applicable to a homogeneous elastic material, It is useful for providing a failure criterion for brittle materials.

The magnitude of K depends on sample geometry, the size and location of the crack, and the magnitude and the modal distribution of loads on the material.

Linear elastic theory predicts a variation, for mode I, near the crack tip of the form

$sigma_\left\{ij\right\} = frac \left\{K_I f_\left\{ij\right\} \left( heta\right)\right\} \left\{ sqrt\left\{\left(2 pi r\right)$

This breaks down very close to the tip (small r), where plastic distortion typically occurs

Critical Stress Intensity

Stress Intensity, K, is a parameter that amplifies the magnitude of the applied stress that includes the geometrical parameter Y (load type). These load types are categorized as Mode-I, -II, or -III. Stress intensity (K) in any mode situation is directly proportional to the applied load on the material. If a very sharp crack can be made in a material, the minimum value of K_I can be empirically determined, which is the critical value of stress intensity required to propagate the crack. This critical value determined for mode I loading in plane-strain is referred to as the critical fracture toughness (KIc) of the material. KIc has units of stress times the root of a distance. The units of KIc infer that the fracture stress of the material must be reached over some critical distance in order for KIc to be reached and crack propagation to occur. The Mode-I critical stress intensity factor, KIc is the most often used engineering design parameter in fracture mechanics and hence must be understood if we are to design fracture tolerant materials used in bridges, buildings, aircraft, or even bells. Polishing just won't do if we detect a crack. Typically for most materials if a crack can be seen it is very close to the critical stress state predicted by the "Stress Intensity Factor".

Mode I is opening or tensile mode where the crack surfaces move directly apart. Mode II is sliding or in-plane shear mode where the crack surfaces slide over one another in a direction perpendicular to the leading edge of the crack. Mode III is tearing and antiplane shear mode where the crack surfaces move relative to one another and parallel to the leading edge of the crack. Mode I is the most common load type encountered in engineering design.

Three different basic modes are shown in the figure.

imple case

The stress intensity factor for a through crack of length 2a, at right angles, in an infinite plane, to a uniform stress field σ is

$K_I=sigma sqrt\left\{pi a\right\}$

References

*A compendium of stress intensity factors for various load and specimen geometries is found in "The Stress Analysis of Cracks Handbook" by Hiroshi Tada, P. C. Paris, and George Rankine Irwin; American Society of Mechanical Engineers; 3rd edition (February, 2000).
*Software to calculate stress intensity is available in a program called pc-CRACKT from Structural Integrity Associates

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• Stress-intensity factor — Stress intensity factor. См. Коэффициент интенсивности напряжения. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

• stress intensity factor — a scale factor to define the magnitude of the crack tip stress field; the functionality depends on the configuration of the cracked component and the manner in which the loads are applied …   Mechanics glossary

• Stress-intensity factor range — Stress intensity factor range. См. Амплитуда коэффициента интенсивности напряжения (K). (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

• Maximum stress intensity factor (Kmax) — Maximum stress intensity factor (Kmax). См. Фактор интенсивности максимального напряжения. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

• Minimum stress-intensity factor (Kmin) — Minimum stress intensity factor (Kmin). См. Минимальный коэффициент интенсивности напряжения. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

• Stress concentration — A stress concentration (often called stress raisers or stress risers) is a location in an object where stress is concentrated. An object is strongest when force is evenly distributed over its area, so a reduction in area, e.g. caused by a crack,… …   Wikipedia

• Stress–strain curve — During testing of a material sample, the stress–strain curve is a graphical representation of the relationship between stress, derived from measuring the load applied on the sample, and strain, derived from measuring the deformation of the sample …   Wikipedia

• factor — atomic packing factor radiation view factor radiation shape factor relative magnification factor stress intensity factor …   Mechanics glossary

• Stress corrosion cracking — (SCC) is the unexpected sudden failure of normally ductile metals or tough thermoplastics subjected to a tensile stress in a corrosive environment, especially at elevated temperature (in the case of metals). SCC is highly chemically specific in… …   Wikipedia

• stress — [stres] n. [ME stresse < OFr estresse < VL * strictia < L strictus,STRICT; also, in some senses, aphetic < DISTRESS] 1. strain or straining force; specif., a) force exerted upon a body, that tends to strain or deform its shape b) the… …   English World dictionary