Shape-memory alloy

Shape-memory alloy

A shape-memory alloy (SMA, smart metal, memory metal, memory alloy, muscle wire, smart alloy) is an alloy that "remembers" its original, cold-forged shape: returning the pre-deformed shape by heating. This material is a lightweight, solid-state alternative to conventional actuators such as hydraulic, pneumatic, and motor-based systems. Shape-memory alloys have applications in industries including medical and aerospace.

Contents

Overview

The three main types of shape-memory alloys are the copper-zinc-aluminium-nickel, copper-aluminium-nickel, and nickel-titanium (NiTi) alloys but SMAs can also be created by alloying zinc, copper, gold and iron. NiTi alloys are generally more expensive and change from austenite to martensite upon cooling; Mf is the temperature at which the transition to martensite completes upon cooling. Accordingly, during heating As and Af are the temperatures at which the transformation from martensite to austenite starts and finishes. Repeated use of the shape-memory effect may lead to a shift of the characteristic transformation temperatures (this effect is known as functional fatigue, as it is closely related with a change of microstructural and functional properties of the material).[1]

The transition from the martensite phase to the austenite phase is only dependent on temperature and stress, not time, as most phase changes are, as there is no diffusion involved. Similarly, the austenite structure receives its name from steel alloys of a similar structure. It is the reversible diffusionless transition between these two phases that results in special properties. While martensite can be formed from austenite by rapidly cooling carbon-steel, this process is not reversible, so steel does not have shape-memory properties.

Sma wire.jpg

In this figure, ξ(T) represents the martensite fraction. The difference between the heating transition and the cooling transition gives rise to hysteresis where some of the mechanical energy is lost in the process. The shape of the curve depends on the material properties of the shape-memory alloy, such as the alloying.[2] and work hardening.[3]

One-way vs. two-way shape memory

Shape-memory alloys have different shape-memory effects. Two common effects are one-way and two-way shape memory. A schematic of the effects is shown below.

one-way shape memoryTwo-way intrinsic shape memory

The procedures are very similar: starting from martensite (a), adding a reversible deformation for the one-way effect or severe deformation with an irreversible amount for the two-way (b), heating the sample (c) and cooling it again (d).

One-way memory effect

When a shape-memory alloy is in its cold state (below As), the metal can be bent or stretched and will hold those shapes until heated above the transition temperature. Upon heating, the shape changes to its original. When the metal cools again it will remain in the hot shape, until deformed again.

With the one-way effect, cooling from high temperatures does not cause a macroscopic shape change. A deformation is necessary to create the low-temperature shape. On heating, transformation starts at As and is completed at Af (typically 2 to 20 °C or hotter, depending on the alloy or the loading conditions). As is determined by the alloy type and composition and can vary between −150 °C and 200 °C.

Two-way memory effect

The two-way shape-memory effect is the effect that the material remembers two different shapes: one at low temperatures, and one at the high-temperature shape. A material that shows a shape-memory effect during both heating and cooling is called two-way shape memory. This can also be obtained without the application of an external force (intrinsic two-way effect). The reason the material behaves so differently in these situations lies in training. Training implies that a shape memory can "learn" to behave in a certain way. Under normal circumstances, a shape-memory alloy "remembers" its high-temperature shape, but upon heating to recover the high-temperature shape, immediately "forgets" the low-temperature shape. However, it can be "trained" to "remember" to leave some reminders of the deformed low-temperature condition in the high-temperature phases. There are several ways of doing this.[4] A shaped, trained object heated beyond a certain point will lose the two-way memory effect, this is known as "amnesia".

Pseudo-elasticity

One of the commercial uses of shape-memory alloy exploits the pseudo-elastic properties of the metal during the high-temperature (austenitic) phase. The frames of reading glasses have been made of shape-memory alloy as they can undergo large deformations in their high-temperature state and then instantly revert back to their original shape when the stress is removed. This is the result of pseudoelasticity; the martensitic phase is generated by stressing the metal in the austenitic state and this martensite phase is capable of large strains. With the removal of the load, the martensite transforms back into the austenite phase and resumes its original shape.

This allows the metal to be bent, twisted and pulled, before reforming its shape when released. This means the frames of shape-memory alloy glasses are claimed to be "nearly indestructible" because it appears no amount of bending results in permanent plastic deformation.

The martensite temperature of shape-memory alloys is dependent on a number of factors including alloy chemistry. Shape-memory alloys with transformation temperatures in the range of 60–1450 K have been made.

History

The first reported steps towards the discovery of the shape-memory effect were taken in the 1930s. According to Otsuka and Wayman, A. Ölander discovered the pseudoelastic behavior of the Au-Cd alloy in 1932. Greninger and Mooradian (1938) observed the formation and disappearance of a martensitic phase by decreasing and increasing the temperature of a Cu-Zn alloy. The basic phenomenon of the memory effect governed by the thermoelastic behavior of the martensite phase was widely reported a decade later by Kurdjumov and Khandros (1949) and also by Chang and Read (1951).[1]

The nickel-titanium alloys were first developed in 1962–1963 by the United States Naval Ordnance Laboratory and commercialized under the trade name Nitinol (an acronym for Nickel Titanium Naval Ordnance Laboratories). Their remarkable properties were discovered by accident. A sample that was bent out of shape many times was presented at a laboratory management meeting. One of the associate technical directors, Dr. David S. Muzzey, decided to see what would happen if the sample was subjected to heat and held his pipe lighter underneath it. To everyone's amazement the sample stretched back to its original shape.[5][6]

There is another type of SMA, called a ferromagnetic shape-memory alloy (FSMA), that changes shape under strong magnetic fields. These materials are of particular interest as the magnetic response tends to be faster and more efficient than temperature-induced responses.

Metal alloys are not the only thermally-responsive materials; shape-memory polymers have also been developed, and became commercially available in the late 1990s.

Crystal structures

Many metals have several different crystal structures at the same composition, but most metals do not show this shape-memory effect. The special property that allows shape-memory alloys to revert to their original shape after heating is that their crystal transformation is fully reversible. In most crystal transformations, the atoms in the structure will travel through the metal by diffusion, changing the composition locally, even though the metal as a whole is made of the same atoms. A reversible transformation does not involve this diffusion of atoms, instead all the atoms shift at the same time to form a new structure, much in the way a parallelogram can be made out of a square by pushing on two opposing sides. At different temperatures, different structures are preferred and when the structure is cooled through the transition temperature, the martensitic structure forms from the austenitic phase.

Manufacture

Shape-memory alloys are typically made by casting, using vacuum arc melting or induction melting. These are specialist techniques used to keep impurities in the alloy to a minimum and ensure the metals are well mixed. The ingot is then hot rolled into longer sections and then drawn to turn it into wire.

The way in which the alloys are "trained" depends on the properties wanted. The "training" dictates the shape that the alloy will remember when it is heated. This occurs by heating the alloy so that the dislocations re-order into stable positions, but not so hot that the material recrystallizes. They are heated to between 400 °C and 500 °C for 30 minutes. Typical variables for some alloys are 500 °C and for more than 5 minutes.

They are then shaped while hot and are cooled rapidly by quenching in water or by cooling with air.

Properties

The copper-based and NiTi-based shape-memory alloys are considered to be engineering materials. These compositions can be manufactured to almost any shape and size.

The yield strength of shape-memory alloys is lower than that of conventional steel, but some compositions have a higher yield strength than plastic or aluminum. The yield stress for Ni Ti can reach 500 MPa. The high cost of the metal itself and the processing requirements make it difficult and expensive to implement SMAs into a design. As a result, these materials are used in applications where the super elastic properties or the shape-memory effect can be exploited. The most common application is in actuation.

One of the advantages to using shape-memory alloys is the high level of recoverable plastic strain that can be induced. The maximum recoverable strain these materials can hold without permanent damage is up to 8% for some alloys. This compares with a maximum strain 0.5% for conventional steels.

Applications

Industrial

Aircraft

Boeing, General Electric Aircraft Engines, Goodrich Corporation, NASA, and All Nippon Airways developed the Variable Geometry Chevron using shape-memory alloy that reduces aircraft's engine noise.

Piping

The first consumer commercial application for the material was as a shape-memory coupling for piping, e.g. oil line pipes for industrial applications, water pipes and similar types of piping for consumer/commercial applications.

Automotive

The first high volume product (> 5Mio actuators / annual) is an automotive valve application build to run low pressure pneumatics /bladders in a car seat to adjust the contour (lumbar support / bolsters). The accounting of basical all benefits of SMA over solenoids (noise/EMC/weight/package (form factor)/power consumption) was the crucial factor to replace the standard technology by SMA. Where in other applications usually just 2 or 3 SMA benefits are considered and hinder from replacing the 'old' technologies.

Telecommunication

The second high volume application was an AF Autofocus actuator for a smart phone. In this moment there are different companies working on an OIS (optical image stabilisation) module driven by SMA wires.

Robotics

There have also been limited studies on using these materials in robotics, for example the hobbyist robot Stiquito (and "Roboterfrau Lara"[7]), as they make it possible to create very light robots. Weak points of the technology are energy inefficiency, slow response times, and large hysteresis.

Medicine

Shape-memory alloys are applied in medicine, for example, as fixation devices for osteotomies in orthopaedic surgery, in dental braces to exert constant tooth-moving forces on the teeth.

The late 1980s saw the commercial introduction of Nitinol as an enabling technology in a number of minimally invasive endovascular medical applications. While more costly than stainless steel, the self expanding properties of Nitinol alloys manufactured to BTR (Body Temperature Response), have provided an attractive alternative to balloon expandable devices in stent grafts where it gives the ability to adapt to the shape of certain blood vessels when exposed to body temperature. On average, 50% of all peripheral vascular stents currently available on the worldwide market are manufactured with Nitinol.

Optometry

Eyeglass frames made from titanium-containing SMAs are marketed under the trademarks Flexon and TITANflex. These frames are usually made out of shape-memory alloys that have their transition temperature set below the expected room temperature. This allows the frames to undergo large deformation under stress, yet regain their intended shape once the metal is unloaded again. The very large apparently elastic strains are due to the stress-induced martensitic effect, where the crystal structure can transform under loading, allowing the shape to change temporarily under load. This means that eyeglasses made of shape-memory alloys are more robust against being accidentally damaged.

Orthopedic surgery

Memory metal has been utilized in orthopedic surgery as a fixation-compression device for osteotomies, typically for lower extremity procedures. The device, usually in the form of a large staple, is stored in a refrigerator in its malleable form and is implanted into pre-drilled holes in the bone across an osteotomy. As the staple warms it returns to its non-malleable state and compresses the bony surfaces together to promote bone union.[8]

Dentistry

The range of applications for SMAs has grown over the years, a major area of development being dentistry. One example is the prevalence of dental braces using SMA technology to exert constant tooth-moving forces on the teeth; the nitinol archwire was developed in 1972 by orthodontist George Andreasen.[9] This revolutionized clinical orthodontics and has also had an effect on fiber optic development. Andreasen's alloy has a patterned shape memory, expanding and contracting within given temperature ranges because of its geometric programming.

Harmeet D. Walia later utilized the alloy in the manufacture of root canal files for endodontics.

Materials

Alloys of metals having the memory effect at different temperatures and at different percentages of its solid solution contents.

  • Ag-Cd 44/49 at.% Cd
  • Au-Cd 46.5/50 at.% Cd
  • Cu-Al-Ni 14/14.5 wt.% Al and 3/4.5 wt.% Ni
  • Cu-Sn approx. 15 at.% Sn
  • Cu-Zn 38.5/41.5 wt.% Zn
  • Cu-Zn-X (X = Si, Al, Sn)
  • Fe-Pt approx. 25 at.% Pt
  • Mn-Cu 5/35 at.% Cu
  • Fe-Mn-Si
  • Pt alloys
  • Co-Ni-Al
  • Co-Ni-Ga
  • Ni-Fe-Ga
  • Ti-Pd in various concentrations
  • Ni-Ti (~55% Ni)
  • Ni-Ti-Nb
  • Ni-Mn-Ga

References

  1. ^ a b Shape Memory Materials, K Otsuka, CM Wayman, Cambridge University Press, 1999 ISBN 0521663849, Google Books
  2. ^ Wu, S; Wayman, C (1987). "Martensitic transformations and the shape-memory effect in Ti50Ni10Au40 and Ti50Au50 alloys☆". Metallography 20: 359. doi:10.1016/0026-0800(87)90045-0. 
  3. ^ Filip, P (1995). "Influence of work hardening and heat treatment on the substructure and deformation behaviour of TiNi shape memory alloys". Scripta Metallurgica et Materialia 32: 1375. doi:10.1016/0956-716X(95)00174-T. 
  4. ^ Shape Memory Alloy Shape Training Tutorial
  5. ^ Kauffman, George, and Isaac Mayo. "Memory Metal." Chem Matters Oct. 1993: 4–7.
  6. ^ Oral history by William J. Buehler
  7. ^ The Lara Project – G1 and G2
  8. ^ . PMID 16546946. 
  9. ^ New York Times obituary of Dr. Andreasen

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • shape memory alloy —  Shape Memory Alloy  Cплав памяти формы   Сплав, который может вернуть свою первоначальную форму после деформации, например путем нагрева до температуры выше температуры полиморфного превращения …   Толковый англо-русский словарь по нанотехнологии. - М.

  • Shape memory alloy — A shape memory alloy (SMA, also known as a smart alloy, memory metal, or muscle wire) is an alloy that remembers its shape, and can be returned to that shape after being deformed, by applying heat to the alloy. When the shape memory effect is… …   Wikipedia

  • shape memory alloy — noun Any of a group of metallic materials that can return to a previously defined shape, after being deformed, by being heated …   Wiktionary

  • Magnetic shape-memory alloy — Magnetic shape memory alloys (MSMAs), or ferromagnetic shape memory alloys (FSMAs), are ferromagnetic materials which exhibit large strains under the influence of an applied magnetic field due to martensitic phase transformation. Magnetic shape… …   Wikipedia

  • Shape memory coupling — is a system for connecting pipes using shape memory alloys. In its typical form the technique uses an internally ribbed sleeve of alloy such as Tinel that is slightly smaller in diameter than the pipes it is to connect. The sleeve is cooled in… …   Wikipedia

  • Magnetic shape memory — (MSM) alloys are ferromagnetic materials exhibiting large changes in shape and size in an applied magnetic field.External links [http://www.fyslab.hut.fi/epm/heusler/ Magnetic shape memory alloys] at the Helsinki University of Technology …   Wikipedia

  • Memory (disambiguation) — Memory is an organism s ability to store, retain, and recall information. Memory or Memories may also refer to: Contents 1 Music 1.1 Songs 1.2 Alb …   Wikipedia

  • Memory-Metall — Formgedächtnislegierungen (FGL, engl. shape memory alloy, SMA) werden oft auch als Memorymetalle bezeichnet. Dies rührt von dem Phänomen, dass sie sich an eine frühere Formgebung trotz nachfolgender starker Verformung scheinbar „erinnern“ können …   Deutsch Wikipedia

  • Memory Metall — Formgedächtnislegierungen (FGL, engl. shape memory alloy, SMA) werden oft auch als Memorymetalle bezeichnet. Dies rührt von dem Phänomen, dass sie sich an eine frühere Formgebung trotz nachfolgender starker Verformung scheinbar „erinnern“ können …   Deutsch Wikipedia

  • Titanium alloy — Titanium alloys are metallic materials which contain a mixture of titanium and other chemical elements. Such alloys have very high tensile strength and toughness (even at extreme temperatures), light weight, extraordinary corrosion resistance,… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”