Litz wire


Litz wire

Litz wire is a special type of wire used in electronics. The wire is designed to reduce the skin effect and proximity effect losses in conductors. It consists of many thin wires, individually coated with an insulating film and twisted or woven together, following a carefully prescribed [http://www.newenglandwire.com/catalog/page129-litz-winding_wires-litz_wire_types-type_1-type_2-type_3-type_4-type_5-type_6-type_7-type_8.htm pattern] often involving several levels (groups of twisted wires are twisted together, etc.).

The term litz wire originates from "Litzendraht", German for bundled wire.

Principle of Operation

Litz wire reduces the impact of the skin effect and the proximity effect.

kin Effect

The resistance of an isolated conductor at DC (0 Hz) depends on its cross sectional area. A conductor with a larger area has a lower resistance. The skin effect causes that resistance to increase for AC currents.

For low frequencies, the effect is negligible. For AC current at frequencies high enough that the skin depth is small compared to the conductor size, the skin effect causes most of the conduction to happen at the conductor's surface. At high enough frequencies, the interior of a large conductor does not carry much current. At 60 Hz, the skin depth of a copper wire is about 1/3 inch (1 cm). At 60 kHz, the skin depth of copper is about about 0.01 inch. At 6 MHz, the skin depth is about 0.001 inch. Round conductors larger than a few skin depths don't conduct much current near their axis, so that material isn't used effectively.

When larger area conductors are needed, tricks are used to minimize the skin effect. The goal is to increase the conducting surface area. One trick is to use a hollow conductor with a wall that is about a skin-depth thick. It is essentially a fat wire with the non-current carrying interior deleted. It is bulky, but it saves copper.

Litz wire uses some different tricks. Instead of using one big conductor, it uses lots of little conductors (strands) in parallel (forming a bundle). Each little conductor is less than a skin-depth, so an individual strand does not suffer an appreciable skin effect loss. However, that is not the complete story. The strands must be insulated from each other -- otherwise all the wires in the bundle would short together, look like a single large wire, and still have skin effect problems. Furthermore, the strands cannot occupy the same radial position in the bundle: the electromagnetic effects that cause the skin effect would still disrupt conduction. The bundle is constructed so the individual strands are on the outside of the bundle (and see low resistance) for a time, but also reside in the interior of the bundle (where the EM field changes are the strongest and the resistance is higher). If each strand sees about the same average resistance, then each strand will contribute equally to the conduction of the entire cable.

The weaving or twisting pattern of litz wire is designed so individual wires will reside for short intervals on the outside of cable and for short intervals on the inside of the cable. This allows the interior of the litz wire to contribute to the cable's conductivity.

Another way to explain the same effect is as follows: the magnetic fields generated by current flowing in the strands are in directions such that they have a reduced tendency to generate an opposing e.m.f. in the other strands. Thereby, for the wire as a whole, the skin effect and associated power losses when used in high-frequency applications are reduced. The ratio of distributed inductance to distributed resistance is increased, relative to a solid conductor, resulting in a higher Q factor at these frequencies.

Proximity Effect

In cases involving multiple wires, or multiple turns, such as windings in transformers and inductors, proximity effect causes losses to increase at high frequency even sooner and more rapidly than does skin effect.

Effectiveness

Terman [cite book |first=Frederick E.| last=Terman|title= Radio Engineers' Handbook|publisher= McGraw-Hill|year=1943 |pages = 37, 74, 80.] provides an expression for the ratio of resistance to alternating current to resistance to direct current for a single litz wire. It does not apply to windings with multiple turns. An expression for the resistance ratio in windings is given by Sullivan [Charles R. Sullivan, "Optimal Choice for Number of Strands in a Litz-Wire Transformer Winding", IEEE Transactions on Power Electronics, 14(2), 1999,http://thayer.dartmouth.edu/inductor/papers/litzj.pdf, Eqn. (2).] .

Litz wire is very effective below 500 kHz; it is rarely used above 2 MHz as it is much less effective there.cite book | last = Terman | first = Frederick E | title = Radio Engineers' Handbook | page = 37]

Applications

Litz wire is used to make inductors and transformers, especially for high frequency applications where the skin effect is more pronounced and proximity effect can be an even more severe problem. Litz wire is one kind of stranded wire, but, in this case, the reason for its use is not the usual one of avoiding complete wire breakage due to material fatigue.

WWVB Transmitting Station

The NIST uses litz wire in the time code broadcasting station WWVB. The station transmits on 60 kHz. The litz wire consists of 6075 strands of #36 magnet wire in a cable 0.75 inches in diameter. Litz wire is used in an impressive variometer (i.e., variable inductor, not the aircraft vertical-velocity indicator also called a variometer). [ [http://www.spawar.navy.mil/sti/publications/pubs/tr/1693/tr1693.pdf Report TR 1693.] ]

Notes

ee also

*Proximity effect
*Skin effect
*Skin depth

References

Peder Hansen and Darrell Gish, WWVB Antenna and Antenna Tuning System, TR 1693, February 1995. [http://www.spawar.navy.mil/sti/publications/pubs/tr/1693/tr1693.pdf TR1693] , [http://stinet.dtic.mil/oai/oai?&verb=getRecord&metadataPrefix=html&identifier=ADA299078 DTIC ADA299078] .

External links

* [http://www.newenglandwire.com/litz.asp New England Wire was the first US manufacturer of Litz and offers free technical assistance regarding the use of litz in various applications]
* [http://www.litz-wire.com/ The Litz People at HM Wire offer a lot of information and support related to Litz wire]
* [http://www.energysaver.com.ar Energy Saver's Website, manufacturer and exporter of Litz wire in Argentina]
* [http://www.or64.com/html/lgm.htm LGM's Website, manufacturer of Litz Wire in Spain]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • litz wire — ˈlits noun Etymology: part translation of German litzendraht, from litze braid, cord, lace + draht wire : a wire composed of individually enameled copper strands braided together to reduce skin effect and consequent high frequency resistance * *… …   Useful english dictionary

  • litz wire — /lits/, Elect. a wire used as a conductor of alternating current, composed of a number of insulated strands woven together to reduce skin effect. [1925 30; partial trans. of G Litzendraht wire made up of strands, equiv. to Litze ( < L licium… …   Universalium

  • Litz — can refer to:* Litz wire a braided wire used in electronics. * Deacon Litz racecar driver. * John Litz politician. * Nadia Litz actress. * Thomas Litz figure skater. * Litz, Oise, a commune in northern France …   Wikipedia

  • Wire — For other uses, see Wire (disambiguation). Wires overhead A wire is a single, usually cylindrical, flexible strand or rod of metal. Wires are used to bear mechanical loads and to carry electricity and telecommunications signals. Wire is commonly… …   Wikipedia

  • Copper wire and cable — Copper has been used in electric wiring since the invention of the electromagnet and the telegraph in the 1820s.[1][2] The invention of the telephone in 1876 proved to be another early boon for copper wire.[3] Today, despite competition from… …   Wikipedia

  • American wire gauge — (AWG), also known as the Brown Sharpe wire gauge, is a standardized wire gauge system used since 1857 predominantly in the United States for the diameters of round, solid, nonferrous, electrically conducting wire. [ASTM Standard B 258 02,… …   Wikipedia

  • Skin effect — Skin depth redirects here. For the depth (layers) of biological/organic skin, see skin. Skin effect is the tendency of an alternating electric current (AC) to distribute itself within a conductor with the current density being largest near the… …   Wikipedia

  • Proximity effect (electromagnetism) — In a conductor carrying current, if currents are flowing through one or more other nearby conductors, such as within a closely wound coil of wire, the distribution of current within the first conductor will be constrained to smaller regions. The… …   Wikipedia

  • Celanese — (NYSE|CE) is a large American chemical company based in Dallas, Texas. The company produces chemicals, fibers, pharmaceuticals and plastics, such as the thermoplastic cellulose acetate used to produce cigarette filters. [… …   Wikipedia

  • Alternating current — (green curve). The horizontal axis measures time; the vertical, current or voltage. In alternating current (AC, also ac) the movement of electric charge periodically reverses direction. In direct current (DC, also dc), the flow of electric charge …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.