Flash (manufacturing)


Flash (manufacturing)

Flash, also known as flashing, is excess material attached to a molded, forged, or cast product, which must usually be removed. This is typically caused by leakage of the material between the two surfaces of a mold (beginning along the parting line[1]) or between the base material and the mold (in the case of overmolding). Molding flash is seen when the optimized parameter on cull height is not calibrated[citation needed]. Proper design of mold parting surfaces can reduce or eliminate flash.[2]

Molding flash can be caused from old or worn mold cavities that no longer fit tightly together. Other times, the complexity of the part requires so many mating pieces with such precise geometries that it is almost impossible to create a perfect fit on every impression. Most often, the type of material being molded, and its attendant viscosity in its liquid form, is the primary factor that leads to the creation of the unwanted mold flash.[3]

The process of removing flash, known as deflashing, is commonly performed via cutting, breaking, grinding, or tumbling. Some foundries use robot autogrinders to remove this unwanted material.

Witness mark

In plastic injection, a faint mark called witness mark (or witness line) will occur along the parting line.[1] This is unavoidable and is usually accepted despite minor aesthetics issue. However, some part surfaces (e.g. when used for sealing[4]) cannot tolerate witness mark, and thus either the mark must be removed post-molding or the mold redesigned.

See also

References

  1. ^ a b David Kazmer (2007). Injection mold design engineering. Hanser Verlag. p. 70. ISBN 9781569904176. http://books.google.com/books?id=fWTftzWhBp4C&pg=PA70. Retrieved 15 April 2011. 
  2. ^ "NX I-deasVGX Core/Cavity". Siemens PLM Software. 2007. http://www.plm.automation.siemens.com/en_sg/Images/3014_tcm963-4308.pdf. Retrieved 2009-07-01. 
  3. ^ Bozzelli, John "An Expert Tells How to Stop Flash", Plastics Technology, July 2004, accessed May 9, 2011.
  4. ^ US patent 6939500, Bernard, Edward Helmut, "Method and apparatus for eliminating a parting line witness mark from a molded part", issued 2005-09-06 



Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Flash Manufacturing PMI — An estimate of the Manufacturing Purchasing Managers Index (PMI) for a country, based on about 85% of total PMI survey responses each month. It is intended to provide an accurate advance indication of the final PMI data. Because flash PMIs are… …   Investment dictionary

  • Flash memory — Computer memory types Volatile RAM DRAM (e.g., DDR SDRAM) SRAM In development T RAM Z RAM TTRAM Historical Delay line memory Selectron tube Williams tube Non volatile …   Wikipedia

  • Flash of genius — The Flash of Genius Doctrine or Flash of Genius Test was a test for patentability used by the United States Federal Courts for over a decade. The doctrine was formalized in Cuno Engineering Corp. v. Automatic Devices Corp . (314 U.S. 84 (1941))… …   Wikipedia

  • Flash in the pan — Pan Pan, n. [OE. panne, AS. panne; cf. D. pan, G. pfanne, OHG. pfanna, Icel., Sw., LL., & Ir. panna, of uncertain origin; cf. L. patina, E. paten.] 1. A shallow, open dish or vessel, usually of metal, employed for many domestic uses, as for… …   The Collaborative International Dictionary of English

  • Charge trap flash — (CTF) is a new technology for the fabrication of NAND flash devices. It was invented by Samsung Electronics in 2006. The technology depends on a SONOS (semiconductor oxide nitride oxide semiconductor) or MONOS (metal ONOS) capacitor structure,… …   Wikipedia

  • Taxonomy of manufacturing processes — This tree lists various manufacturing processes arranged by similarity of function.#Casting ##Sand casting ##Plastic mold ##Shell mold ##Investment casting (lost wax, precision) ##Permanent mold ##Centrifugal casting ##Die casting ##Slush or… …   Wikipedia

  • USB flash drive — JumpDrive redirects here. For the fictional propulsion system, see Jump drive. SanDisk Cruzer Micro, a brand of USB flash drives …   Wikipedia

  • Williams Manufacturing Company — Logo de Williams Manufacturing Company Dates clés 1943 (création) 1967 (Williams Electronics) 1985 (Will. Electronics Games) 1987 (WMS Industries) 1988 (absorbe Bally Midway) …   Wikipédia en Français

  • Semiconductor Manufacturing International Corporation — Rechtsform Aktiengesellschaft Gründung 2000 Sitz Shanghai, Volksrepublik China Mitarbeiter 9424 (2011) …   Deutsch Wikipedia

  • Single-level cell — Flash memory stores data in individual memory cells, which are made of floating gate transistors. Traditionally, one bit of data was stored in each cell in so called single level cells, or SLC flash memory. SLC memory has the advantage of faster… …   Wikipedia