 Work (physics)

Work SI symbol: W SI unit: joule Derivations from other quantities: W = F · d
In physics, work is a scalar quantity that can be described as the product of a force times the distance through which it acts, and it is called the work of the force. Only the component of a force in the direction of the movement of its point of application does work. The term work was first coined in 1826 by the French mathematician GaspardGustave Coriolis.^{[1]}^{[2]}
If a constant force of magnitude F acts on a point that moves s in the direction of the force, then the work W done by this force is calculated W=Fs. In particular, a force of 10 newtons (F=10N) acting along the path of 2 metres (s=2m) will do the work W=(10N)(2m)=20Nm=20J, where joule (J) is the SI unit for work (derived in order to replace the product Nm).
At any instant, the rate of the work done by a force is the scalar product of the force with the velocity vector of the point of application. This scalar product of force and velocity is called instantaneous power, and work is the time integral of instantaneous power along the trajectory of the point of application. Because changes in this trajectory will change the calculation of work, work is said to be path dependent.
The first law of thermodynamics states that when work is done to a system its energy state changes by the same amount. This equates work and energy. In the case of rigid bodies, Newton's laws can be used to derive a similar relationship called the workenergy theorem.
Contents
Units
See also: Work (thermodynamics)The SI unit of work is the joule (J), which is defined as the work done by a force of one newton acting over a distance of one metre. This definition is based on Sadi Carnot's 1824 definition of work as "weight lifted through a height", which is based on the fact that early steam engines were principally used to lift buckets of water, through a gravitational height, out of flooded ore mines. The dimensionally equivalent newtonmetre (N·m) is sometimes used for work, but this can be confused with the units newtonmetre of torque.
NonSI units of work include the erg, the footpound, the footpoundal, and the litreatmosphere. Other nonSI units for work are the horsepowerhour, the therm, the BTU and Calorie. It is important to note that heat and work are measured using the same units.
Heat conduction is not considered to be a form of work, since the energy is transferred into atomic vibration rather than a macroscopic displacement. However, heat conduction can perform work by expanding a gas in a cylinder such as in the engine of an automobile.
Mathematical calculation
Calculating the work as "force times straight path segment" can only be done in the simple circumstances described above. If the force is changing, if the body is moving along a curved path, possibly rotating and not necessarily rigid, then only the path of the application point of the force is relevant for the work done, and only the component of the force parallel to the application point velocity is doing work (positive work when in the same direction, and negative when in the opposite direction of the velocity). This component of the force can be described by the scalar quantity called scalar tangential component (, where is the angle between the force and the velocity). And then the most general definition of work can be formulated as follows:
 Work of a force is the line integral of its scalar tangential component along the path of its application point.
Simpler (intermediate) formulas for work and the transition to the general definition are described in the text below.
Force and displacement
If a force F that is constant with respect to time acts on an object while the object is translationally displaced for a displacement vector d, the work done by the force on the object is the dot product of the vectors F and d:^{[3]}
 (1)
where is the angle between the force and the displacement vector.
Whereas the magnitude and direction of the force must remain constant, the object's path may have any shape: the work done is independent of the path and is determined only by the total displacement vector . A most common example is the work done by gravity – see diagram. The object descends along a curved path, but the work is calculated from , which gives the familiar result .
More generally, if the force causes (or affects) rotation of the body, or if the body is not rigid, displacement of the point to which the force is applied (the application point) must be used to calculate the work. This is also true for the case of variable force (below) where, however, magnitude of can equally be interpreted as differential displacement magnitude or differential length of the path of the application point. (Although use of displacement vector most frequently can simplify calculation of work, in some cases simplification is achieved by use of the path length, as in the work of torque calculation below.)
In situations where the force changes over time, equation (1) is not generally applicable. But it is possible to divide the motion into small steps, such that the force is well approximated as being constant for each step, and then to express the overall work as the sum over these steps. This will give an approximate result, which can be improved by further subdivisions into smaller steps (numerical integration). The exact result is obtained as the mathematical limit of this process, leading to the general definition below.
The general definition of mechanical work is given by the following line integral:
 (2)
where:
 is the path or curve traversed by the application point of the force;
 is the force vector;
 is the position vector; and
 is its velocity.
The expression is an inexact differential which means that the calculation of is pathdependent and cannot be differentiated to give .
Equation (2) explains how a nonzero force can do zero work. The simplest case is where the force is always perpendicular to the direction of motion, making the integrand always zero. This is what happens during circular motion. However, even if the integrand sometimes takes nonzero values, it can still integrate to zero if it is sometimes negative and sometimes positive.
The possibility of a nonzero force doing zero work illustrates the difference between work and a related quantity, impulse, which is the integral of force over time. Impulse measures change in a body's momentum, a vector quantity sensitive to direction, whereas work considers only the magnitude of the velocity. For instance, as an object in uniform circular motion traverses half of a revolution, its centripetal force does no work, but it transfers a nonzero impulse.
Torque and rotation
Work done by a torque can be calculated in a similar manner, as is easily seen when a force of constant magnitude is applied perpendicularly to a lever arm. After extraction of this constant value, the integral in the equation (2) gives the path length of the application point, i.e. the circular arc , and the work done is .
However, the arc length can be calculated from the angle of rotation (expressed in radians) as , and the ensuing product is equal to the torque applied to the lever arm. Therefore, a constant torque does work as follows:
Work and kinetic energy
According to the workenergy theorem, if one or more external forces act upon a rigid object, causing its kinetic energy to change from E_{k1} to E_{k2}, then the work (W) done by the net force is equal to the change in kinetic energy. For translational motion, the theorem can be specified as:^{[4]}
where m is the mass of the object and v is the object's velocity.
The theorem is particularly simple to prove for a constant force acting in the direction of motion along a straight line. For more complex cases, however, it can be claimed that very concept of work is defined in such a way that the workenergy theorem remains valid.
Derivation for a particle
In rigid body dynamics, a formula equating work and the change in kinetic energy of the system is obtained as a first integral of Newton's second law of motion.
To see this, consider a particle P that follows the trajectory X(t) with a force F acting on it. Newton's second law provides a relationship between the force and the acceleration of the particle as
where m is the mass of the particle.
The scalar product of each side of Newton's law with the velocity vector yields
which is integrated from the point X(t_{1}) to the point X(t_{2}) to obtain
The left side of this equation is the work of the force as it acts on the particle along the trajectory from time t_{1} to time t_{2}. This can also be written as
This integral is computed along the trajectory X(t) of the particle and is therefore path dependent.
The right side of the first integral of Newton's equations can be simplified using the identity
which can be integrated explicitly to obtain the change in kinetic energy,
where the kinetic energy of the particle is defined by the scalar quantity,
The result is the workenergy principle for rigid body dynamics,
This derivation can be generalized to arbitrary rigid body systems.
Frame of reference
The work done by a force acting on an object depends on the choice of reference frame because displacements and velocities are dependent on the reference frame in which the observations are being made.^{[5]}
The change in kinetic energy also depends on the choice of reference frame because kinetic energy is a function of velocity. However, regardless of the choice of reference frame, the work energy theorem remains valid and the work done on the object is equal to the change in kinetic energy.^{[6]}
Zero work
An important class of forces in mechanical systems perform zero work. These are constraint forces that restrict the relative movement of bodies. For example, the centripetal force exerted by a string on a ball a uniform circular motion does zero work because this force is perpendicular to the velocity of the ball. As a result the kinetic energy of the moving ball doesn't change.
Another example is a book at rest on a table, the table does no work on the book despite exerting a force equivalent to mg upwards, because no energy is transferred into or out of the book. On the other hand, if the table moves upward, then it performs work on the book, since the force of the table on the book will be acting through a distance.
A current that generates a magnetic field can also produce a magnetic force where a charged particle exerts a force on a magnetic field, but the magnetic force can do no work because the charge velocity is perpendicular to the magnetic field and in order for a force or an object to perform work, the force has to be in the same direction as the distance that it moves.
References
 ^ Jammer, Max (1957). Concepts of Force. Dover Publications, Inc.. ISBN 048640689X.
 ^ Sur une nouvelle dénomination et sur une nouvelle unité à introduire dans la dynamique, Académie des sciences, August 1826
 ^ Resnick, Robert and Halliday, David (1966), Physics, Section 72 (Vol I and II, Combined edition), Wiley International Edition, Library of Congress Catalog Card No. 6611527
 ^ Tipler (1991), page 138.
 ^ Resnick, Robert and Halliday, David (1966), Physics, Section 13 (Vol I and II, Combined edition), Wiley International Edition, Library of Congress Catalog Card No. 6611527
 ^ Resnick, Robert and Halliday, David, Physics, Section 46
Bibliography
 Serway, Raymond A.; Jewett, John W. (2004). Physics for Scientists and Engineers (6th ed. ed.). Brooks/Cole. ISBN 0534408427.
 Tipler, Paul (1991). Physics for Scientists and Engineers: Mechanics (3rd ed., extended version ed.). W. H. Freeman. ISBN 0879014326.
External links
 Work – a chapter from an online textbook
Categories: Introductory physics
 Energy in physics
 Physical quantities
 Mechanical engineering
 Mechanics
 Machines
Wikimedia Foundation. 2010.
Look at other dictionaries:
Work — may refer to: Human labor: Employment House work Labor (economics), measure of the work done by human beings Manual labor, physical work done by people Wage labor, in which a worker sells their labor and an employer buys it Work (project… … Wikipedia
Physics — (Greek: physis φύσις), in everyday terms, is the science of matter [R. P. Feynman, R. B. Leighton, M. Sands (1963), The Feynman Lectures on Physics , ISBN 0 201 02116 1 Hard cover. p.1 1 Feynman begins with the atomic hypothesis.] and its motion … Wikipedia
Physics First — is an educational program that teaches a basic physics course in the ninth grade (usually 15 year olds), rather than the biology course which is more standard in public schools. This course relies on the limited math skills that the students have … Wikipedia
Physics (Aristotle) — Physics (or Physica , or Physicae Auscultationes meaning lessons ) is a key text in the philosophy of Aristotle. It inaugurates the current Andronichean order, the long series of Aristotle s physical, cosmological and biological works, and is… … Wikipedia
work — ► NOUN 1) activity involving mental or physical effort done in order to achieve a result. 2) such activity as a means of earning income. 3) a task or tasks to be undertaken. 4) a thing or things done or made; the result of an action. 5) (works)… … English terms dictionary
PHYSICS — The material presented in this entry emphasizes those contributions which were important in arriving at verified present day scientific results, rather than those that may have appeared important at the time. Unavoidably it will overlap in parts… … Encyclopedia of Judaism
physics — /fiz iks/, n. (used with a sing. v.) the science that deals with matter, energy, motion, and force. [1580 90; see PHYSIC, ICS] * * * I Science that deals with the structure of matter and the interactions between the fundamental constituents of… … Universalium
work — /werrk/, n., adj., v., worked or (Archaic except for 35, 37, 40) wrought; working. n. 1. exertion or effort directed to produce or accomplish something; labor; toil. 2. something on which exertion or labor is expended; a task or undertaking: The… … Universalium
Work function — In solid state physics, the work function is the minimum energy (usually measured in electron volts) needed to remove an electron from a solid to a point immediately outside the solid surface (or energy needed to move an electron from the Fermi… … Wikipedia
Work — /werrk/, n. Henry Clay, 1832 84, U.S. songwriter. * * * I In economics and sociology, the activities and labour necessary for the survival of society. As early as 40,000 BC, hunters worked in groups to track and kill animals, while younger or… … Universalium