Clock-face scheduling

Clock-face scheduling

A clock-face schedule is a timetable, where public means of transport run in consistent intervals. The number of departures per time is the frequency of the service. Its name comes from the fact that departures are usually the same number of minutes past each hour on a clock.

Regular timetables were first developed at the end of the 19th century for local public transport, such as Trams and trains in the vicinity of large cities (e.g. Berlin Stadtbahn).

The goal of clock-face schedules is to increase the attractiveness and versatility of public transport. They are easier to memorize for passengers, because departure times repeat. A constant schedule over the whole day can also improve service during off-peak hours. They can be attractive for transportation companies, because the repeating pattern makes more efficient use of personnel, infrastructure, and vehicles, and can make resource planning easier.

The opposite of a clock-face schedule is a timetable that is purely driven by demand, with irregular headways.

Contents

Line-based

Each line can have an individual regular schedule, without connections to other lines. Even in this case it may be necessary to coordinate different means of transport if the mode of transport changes, for example at the terminal stop of a tram network, if the line continues by bus.

These timetables may be attractive even if they don't provide connections to other public transport, because they allow a continuous use of vehicles and personnel.

Line-bound regular timetables are especially useful for lines with high service frequencies. If vehicles with the same destination follow each other in short intervals, transfer times are short even with delays. However, if the service intervals are 20 minutes or longer, lines usually should be coordinated. One simple way of doing this is to shift the departure times of one of the lines to match the other.

Hubs

Buses meet in Herford, Alter Markt

Having several lines meet at hubs with vehicles of all lines arriving and leaving at the same time is a modern way of connecting multiple lines. Usually, all lines wait for a delayed vehicle. The goal is to reduce transfer times to a few minutes, with a default time of five minutes. However, in actual operation this timespan is often larger due to vehicles being early or late, high passenger volume (e.g. rush hour) or assisting passengers with disabilities. Due to the waiting times at such transfer stops the through service on a line can become unattractive.

Examples of such networks are often nighttime and city bus networks. The connections are only optimized within the network, but not for transfers to rail or intercity bus lines. Such concepts need purpose-built stations which can handle high passenger volumes. The space constraints within cities can be a reason to seek other concepts.

Integrated

An integrated schedule is a clock-face schedule that covers not just some lines, but the whole area served by possibly several different means of public transport. A characteristic of integrated regular timetables is that there is more than one central hub, instead it applies the hub concept to the whole transport network.

The first integrated regular timetables were developed for railways. After the successful introduction of a line-bound regular timetable on one line in Switzerland in 1968[1], the development continued in the Netherlands. In 1970/71 Nederlandse Spoorwegen introduced a regular timetable with multiple hubs. In Germany, the first large-scale use of regular timetables was the InterCity network of 1979, which provided hourly long-distance services between cities. In 1982, a nation-wide integrated regular timetable was introduced in Switzerland, which covered all but a few railway and bus lines. The base frequency was once an hour. The system was improved every two years, and resulted in the Rail 2000 project of Swiss Federal Railways.

Since 1990, most States of Germany have introduced integrated timetables for short-distance public transport, running hourly or every two hours, e.g. Allgäu-Schwaben-Takt in 1993, Rheinland-Pfalz-Takt in 1994 and NRW-Takt in 1998. Transport associations have introduced regular timetables with base frequencies of 20 or 30 minutes, which are partially intensified to 10 or 5 resp. 15 or 7.5 minutes by overlaying multiple lines. In some areas, local buses are also integrated, e.g. RegioTakt in NRW and in parts of Lower Saxony.

These developments have led to "integrated timetable islands", which all do adhere to the Germany-wide symmetry minute (58½), which is used also in Switzerland and partially in other european Countries. Major problems exist in regions where transport associations of different states interact (e.g. at Osnabrück). In order to introduce a Germany-wide integrated regular timetable, the alliance "Deutschland-Takt" was founded in 2008. Its goal is to start a discussion about a better system for public transport in Germany and to highlight room for improvement[2]. The Bundesarbeitsgemeinschaft Schienenpersonennahverkehr (BAG-SPNV) together with Deutsche Bahn AG are currently conducting feasibility studies for a Germany-wide integrated timetable[3].

An integrated regular timetable needs routes that take 28 or 58 minutes, in order for a vehicle to make it from one hub to another in time. In contrast, a route that takes 40 minutes would be bad, because vehicles and possibly passengers would have to wait uselessly for their connections. Thus, a route that takes 40 minutes generates nearly the same cost as a route that takes 58 minutes, because vehicles and personnel can't be used in the remaining 20 minutes. Therefore, lines are often cut or extended to meet this requirement when an integrated timetable is introduced.

Swiss Federal Railways have adapted their infrastructure in such a way that trains need multiples of 30 minutes between hubs, providing good connections to all means of transport that run every half an hour, which is the case for most lines today. However, on some single tracked lines the published timetables may be 30/30 or 60/60 minutes, while the actual timetables are slightly asymmetrical, because the passing loops are not positioned ideally.

References

  1. ^ http://web.archive.org/web/20080306143156/http://ned.gschieder.ch/download/bahn/bahn.htm Section „vertakten“ (German)
  2. ^ deutschland-takt.de
  3. ^ Deutscher Bundestag (Hrsg.): Antwort der Bundesregierung auf die Kleine Anfrage der Abgeordneten Dr. Anton Hofreiter, Winfried Hermann, Bettina Herlitzius, weiterer Abgeordneter und der Fraktion BÜNDNIS 90/DIE GRÜNEN – Drucksache 17/2258 – Untersuchungen zur Liberalisierung des Fernlinienbusverkehrs und seinen Auswirkungen auf den Schienenpersonenfernverkehr. Drucksache 17/2535 vom 8. Juli 2010 (German)

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Public transport — This article is about passenger transportation systems. For mathematics, see transportation theory. For other uses, see Mass transit (disambiguation). Public infrastructure Assets and facilities …   Wikipedia

  • On-time performance — In transportation (such as municipal public transportation), schedule adherence or on time performance refers to the level of success of the service (such as a bus or train) remaining on the published schedule. There are many factors that can… …   Wikipedia

  • Share taxi — State / Territory / Region Name used  Albania Furgon  Algeria Taxis collectifs …   Wikipedia

  • Bus bunching — Two buses on the same route in the same location In public transport bus bunching, clumping, or platooning refers to a group of two or more transit vehicles along the same route, such as buses or trains, which are scheduled to be evenly spaced,… …   Wikipedia

  • Train station — Rail transport Operations Track Maintenance High speed Gauge Stations …   Wikipedia

  • Paratransit — Two Maui Bus buses engaged in paratransit services. One is picking up a person who uses a wheelchair, while another is discharging another person using a mobility scooter. Paratransit is an alternative mode of flexible passenger transportation… …   Wikipedia

  • Demand responsive transport — or Demand Responsive Transit (DRT) or Demand Responsive Service[1] or Dial a ride or Flexible Transport Services[2] is an advanced, user oriented form of public transport characterised by flexible routing and scheduling of small/medium vehicles… …   Wikipedia

  • Staten Island Ferry Whitehall Terminal — Coordinates: 40°42′09″N 74°00′46″W / 40.702472°N 74.012833°W / 40.702472; 74.012833 …   Wikipedia

  • Maglev — JR Maglev at Yamanashi, Japan test track in November 2005 …   Wikipedia

  • Manual fare collection — is the practice of collecting fares manually (without the aid of an automated machine). Fare collection generally refers to the collection of fares in the transport industry in return for a ticket or passes to travel. Commonly used on buses and… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”