Leather carving


Leather carving

"This article describes leather carving in detail. For information about leather craft in general, see Leather crafting."Leather carving is the process of giving a three-dimensional appearance to leather by a process of cutting and stamping the surface.

Materials

The only type of leather suitable for carving is vegetable tanned, full grain leather. This is because the vegetable tanning process allows the leather to absorb water, which is used to soften the leather before the carving process, and the grain of the leather is necessary to allow the leather to hold the shape after the carving process is complete. Other leathers lack these two essential qualities.

Tools

Leather carving is "accomplished" using three main tools:
* Swivel knife - used to make the bold cuts that define the pattern or image being carved
* Rawhide mallet - used to drive the stamps used to mat down the background and create shading and patterns
* Stamp set - A set of stamping tools used to shape and color the leather to create the final image. Usually contains at minimum a beveler, pear shader, seeder, and background tool, but sets often contain other tools and sometimes several variations on the same tool.

Stamping tools

Camouflage Tool

This tool, which creates an impression similar to that of a sea shell, is used to add emphasis to areas of a carving, often in the stem or down the centre of a leaf in a floral design. It is used in a similar way to other stamping tools, by holding it vertically over the leather and striking with the rawhide mallet. When using the Camouflage tool, the impressions created should be equally spaced, starting from the centre of the design and working out towards the tips of the stems or leaves in the design. The impressions should get progressively lighter.

Pear Shader

The Pear Shader is used to press down areas of the design that need to appear curved. The action of the pear shader causes the leather tooled by it to appear slightly darker. The pear shader is slightly unusual in that it may be tilted during use to provide the desired effect. It should be moved only slightly between each tap with the mallet so that it creates a consistent shading of the leather.

Veiner or Shell Tool

These tools create a curved impression of a series of short, closely spaced lines. They may be used interchangeably, the only difference being that the veiner creates a simple curved line, while the shell tool has a pattern resembling the edge of a scallop along the inside edge. They are used to continue to create the impression of depth created by the beveler, and to create the impression of a curved surface. These tools are used in the usual way, but like the pear shader, may also be tilted to help create the impression of depth where they are used beside a cut.

Seeder

The seeder creates a small circular impression, that is used to represent seeds. As the face of this tool is so small, care must be taken when striking that you do not cut right through the leather. If stamping an area using this tool, stamp around the outside first, then fill in the centre.

Background Tool

This step in producing a carved leather article is used to emphasise the design, and is not even necessary in some cases. It consists of the pushing down of any areas of leather that have not been already carved. The background tool has a crosshatched pattern on its head, which has the effect of significantly darkening the leather it is used on. As with the seeder, the face of this tool is often small, so care must be taken not to strike it too hard.

When using this tool, take care that the impressions created by it do not overlap, and also take care not to stamp into the design or over the border. When the entire face of the tool is not needed, or to create tidy corners, the tool can be tilted so only part of the face creates an impression.

Other Stamps

There are many other stamps that may be employed in stamping leather, too many to list here. Many may be adapted for use in carved designs, and these will be found with practice.

Procedure

Casing .all leather needs to be prepared a certan way fpr leather carvers to carve the leather. The leather carver soakes the leather with water ,thus making the leather easer to tool.

One point to note is that if leather is too wet, it will not hold a sharply defined carving.Properly cased leather should be cool to the touch, and should feel like wet clay.

A good way to test if the leather is properly cased is to fold the corner. Properly cased leather should fold smoothly and hold a crease well.

Swivel knife cuts

When the leather has been properly cased, the swivel knife is used to make the bold cuts that form the backbone of the carved image. These cuts are made to a depth of up to approximately half the thickness of the leather being used, depending on the effect desired by the leather worker. Care must be taken during this step to keep the swivel knife vertical at all times, as any tilt is detrimental to the ability of the leather to be properly stamped later in the carving process.

Beveling the cuts

After shading is completed with the Pear Shader, the Beveler is used to compress one side of the cut. This creates the impression of depth by pressing down parts of the image relative to the foreground. The Beveler is used by holding it vertically, with the foot of the tool in contact with the leather, and striking it lightly with the rawhide mallet. The tool is then moved forward along the cut about half its width, and struck again with the mallet. This process is completed until the entire length of the cut has been appropriately beveled.

As a general rule, the outside of curves and the outside edge of anything overlapping another part of the design should be beveled. The exception to this rule is leather that will later be stamped with another tool, and, if the background is to be treated with the background tool, the background itself.

Dress Cuts

This is the final step in creating a carved design. The swivel knife is again used to create small, decorative cuts in the design to enhance its appearance. These cuts may be made in parts of the design that have already been stamped, which is why it is necessary to leave this step until last.


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Leather crafting — is the practice of making leather into craft objects or works of art, using shaping techniques, coloring techniques or both.Leather coloringLeather dyeing usually involves the use of spirit or alcohol based dyes where alcohol quickly gets… …   Wikipedia

  • Leather — For other uses, see Leather (disambiguation). Modern leather working tools Leather is a durable and flexible material created via the tanning of putrescible animal rawhide and skin, primarily cattlehide. It can be produced through different… …   Wikipedia

  • Leather subculture — The leather pride flag, which has become a symbol of BDSM and fetish subcultures …   Wikipedia

  • Artificial leather — is a fabric or finish intended to substitute for leather in fields such as upholstery, clothing and fabrics, and other uses where a leather like finish is required but the actual material is cost prohibitive or unsuitable. Contents 1 Historic and …   Wikipedia

  • Ostrich leather — is the result of tanning skins taken from African ostriches farmed for their feathers, skin and meat. The leather is distinctive for its pattern of bumps or vacant quill follicles, ranged across a smooth field in varying densities. It requires an …   Wikipedia

  • Chamois leather — Shamy redirects here. For the pair of characters from The Big Bang Theory, see List of The Big Bang Theory characters. A Chamois leather cloth Chamois leather (   …   Wikipedia

  • Aniline leather — is a type of leather dyed exclusively with soluble dyes without covering the surface with a topcoat paint or insoluble pigments. The resulting product retains the hide s natural surface with the grain , i.e. visible pores, scars etc. of the… …   Wikipedia

  • Boiled leather — Boiled leather, sometimes called cuir bouilli, was a historical construction material for armour. It consists of thick leather, boiled in water (some sources hold that oil and wax were used as well, others posit the use of ammonia from fermented… …   Wikipedia

  • Nappa leather — or Napa leather is a full grain leather, typically dyed, made from unsplit kid , lamb or sheep skin by tanning with salts of chromium or aluminium sulfate, and noted for softness and durability. It is often used in high quality leather products… …   Wikipedia

  • Morocco leather — Book bound in a mustard yellow morocco. Morocco leather (also morocco or the French maroquin) is a leather made from goatskin,[1][2] dyed red (traditionally using Sumac) on the grain …   Wikipedia