Repointing


Repointing

Repointing is the process of renewing mortar joints in masonry construction. Over time, weathering and decay causes voids in the joints between masonry units (usually bricks) allowing the undesirable ingress of water. Water entering through these voids can cause significant damage through freeze/thaw cycles and from salt dissolution and deposition. Repointing is also called pointing, or pointing up, although these terms more properly refer to the finishing step in new construction.

Construction details

Masonry units are typically laid in a bed of mortar. The process of placing a masonry unit in a mortar bed causes the mortar to be extruded between units. This excess mortar is cleared and shaped before the mortar hardens. In some cases, the bedding mortar is meant to be seen and the mortar joint is immediately given a finish profile. In other cases, especially where the mortar is pigmented, the bedding mortar is removed from the joint before it hardens (usually a depth that averages about one inch), and then pointing mortar is applied in the void and shaped with a finish profile.

Repointing process

Sound mortar normally does not need to be removed from a building during the repointing process, although such a practice is common. New mortar can be designed to match the color and texture of existing mortar to avoid visual aberrations. The repointing process begins by removing damaged pointing to a depth equal to or slightly more than the width of the joint, or to the point where sound mortar is reached. Depths greater than 2-1/2" or 4 cm should be filled in several passes, allowing the mortar to cure for at least 24 hours. The joint profile should be as rectangular as possible as the new pointing mortar should be allowed ample opportunity to bond with the masonry unit.

Removal of old mortar between joints should be done carefully to avoid damage to masonry units. On very old buildings with soft materials, such as under-fired brick, removal by hand is often the most effective to avoid damage. Hard Portland cement mortar is usually removed with a grinder or power circular masonry blade, taking care not to damage the masonry units. Vertical joints in most cases are always done by hand or with small power chisels.

Poor repointing work often raises the level of the mortar joint above the face of the masonry unit, which causes the mortar edge to feather. Such a process is aesthetically undesirable and can cause performance problems as a thin layer of mortar will quickly erode. In addition, depending on the nature of the mortar, mortar that rises above the level of the face of the masonry unit can participate in damaging the arris or corner of the masonry unit. In these cases, deteriorated mortar is often not removed to a sufficient depth.

Repointing materials

It is essential that the mortar used for repointing have similar performance characteristics to the original mortar used in a building. Such performance characteristics include permeability, compressive strength, and coefficient of thermal expansion. For instance, if a soft lime-based mortar was originally used, the most appropriate repointing mortar is likely to also contain a large amount of lime. The use of Portland cement mortar for repointing on older buildings with soft masonry units can cause significant damage due to physical incompatibilities.

An architectural conservator can perform a mortar analysis in order to make recommendations for replacement mortar that is both physically and aesthetically compatible with the building.

ee also

*Stonemasonry
*Tuckpointing

External links

*http://www.maconline.org/tech/maintenance/point1/point1.html

References


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • repointing — noun The process of renewing mortar joints in masonry …   Wiktionary

  • Dimension stone — Large blocks of granite dimension stone being loaded at Teignmouth in 1827. Dimension stone is natural stone or rock that has been selected and fabricated (i.e., trimmed, cut, drilled, ground, or other) to specific sizes or shapes. Color, texture …   Wikipedia

  • Mortar (masonry) — For other uses, see Mortar (disambiguation). Mortar holding weathered bricks Mortar is a workable paste used to bind construction blocks together and fill the gaps between them. The blocks may be stone, brick, cinder blocks, etc. Mortar becomes… …   Wikipedia

  • Tuckpointing — one colour matching the bricks themselves, to give an artificial impression that very fine joints have been made.HistoryThe method was developed in England in the nineteenth century to imitate brickwork constructed using rubbed bricks (or rubbers …   Wikipedia

  • Mortar joint — In masonry, mortar joints are the spaces between bricks, concrete blocks, or glass blocks, that are filled with mortar or grout. Mortar joints can be made in a series of different fashions, but the most common ones are raked, grapevine, extruded …   Wikipedia

  • Brick — For other uses, see Brick (disambiguation). An old brick wall in English bond laid with alternating courses of headers and stretchers …   Wikipedia

  • Concrete — This article is about the construction material. For other uses, see Concrete (disambiguation). Outer view of the Roman Pantheon, still the largest unreinforced solid concrete dome.[1] …   Wikipedia

  • Granite — For other uses, see Granite (disambiguation). Granite Igneous Rock Granite containing potassium feldspar, plagioclase feldspar, quartz, and biotite and/or amphibole Composi …   Wikipedia

  • Marble — For other uses, see Marble (disambiguation). Marble …   Wikipedia

  • Masonry — This article refers to the building structure component; for the fraternal organization, see Freemasonry. A mason laying mortar on top of a finished course of blocks, prior to placing the next course. Masonry is the building of structures from… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.