Agarose gel electrophoresis

Agarose gel electrophoresis is a method used in biochemistry and molecular biology to separate DNA, or RNA molecules by size. This is achieved by moving negatively charged nucleic acid molecules through an agarose matrix with an electric field (electrophoresis). Shorter molecules move faster and migrate farther than longer ones. [Sambrook J, Russel DW (2001). Molecular Cloning: A Laboratory Manual 3rd Ed. Cold Spring Harbor Laboratory Press. Cold Spring Harbor, NY.]

Applications

* Estimation of the size of DNA molecules following restriction enzyme digestion, e.g. in restriction mapping of cloned DNA.
* Analysis of PCR products, e.g. in molecular genetic diagnosis or genetic fingerprinting
* Separation of restricted genomic DNA prior to Southern transfer, or of RNA prior to Northern transfer.

The advantages are that the gel is easily poured, does not denature the samples. The samples can also be recovered.

The disadvantages are that gels can melt during electrophoresis, the buffer can become exhausted, and different forms of genetic material may run in unpredictable forms.

Factors affecting migration

The most important factor is the length of the DNA molecule, smaller molecules travel farther. But conformation of the DNA molecule is also a factor. To avoid this problem linear molecules are usually separated, usually DNA fragments from a restriction digest, linear DNA PCR products, or RNAs.

Increasing the agarose concentration of a gel reduces the migration speed and enables separation of smaller DNA molecules. The higher the voltage, the faster the DNA moves. But voltage is limited by the fact that it heats and ultimately causes the gel to melt. High voltages also decrease the resolution (above about 5 to 8 V/cm).

Conformations of a DNA plasmid that has not been cut with a restriction enzyme will move with different speeds (slowest to fastest): nicked or open circular, linearised, or supercoiled plasmid.

Visualisation: Ethidium Bromide (EtBr) and dyes

The most common dye used to make DNA or RNA bands visible for agarose gel electrophoresis is ethidium bromide, usually abbreviated as EtBr. It fluoresces under UV light when intercalated into DNA (or RNA). By running DNA through an EtBr-treated gel and visualizing it with UV light, any band containing more than ~20ng DNA becomes distinctly visible. EtBr is a known carcinogen, however, and safer alternatives are available.

SYBR Green I is another dsDNA stain, produced by Invitrogen. It is more expensive, but 25 times more sensitive, and possibly safer than EtBr, though there is no data addressing its mutagenicity or toxicity in humans. [ [http://probes.invitrogen.com/media/pis/mp07567.pdf SYBR Green I Nucleic Acid Gel Stain ] ]

SYBR Safe is a variant of SYBR Green that has been shown to have low enough levels of mutagenicity and toxicity to be deemed nonhazardous waste under U.S. Federal regulations. [ [http://probes.invitrogen.com/media/pis/mp33100.pdf SYBR Safe DNA Gel Stain ] ] It has similar sensitivity levels to EtBr, [ [http://probes.invitrogen.com/media/pis/mp33100.pdf SYBR Safe DNA Gel Stain ] ] but, like SYBR Green, is significantly more expensive.

Since EtBr stained DNA is not visible in natural light, scientists mix DNA with negatively charged loading buffers before adding the mixture to the gel. Loading buffers are useful because they are visible in natural light (as opposed to UV light for EtBr stained DNA), and they co-sediment with DNA (meaning they move at the same speed as DNA of a certain length). Xylene cyanol and Bromophenol blue are common loading buffers; they run about the same speed as DNA fragments that are 5000 bp and 300 bp in length respectively, but the precise position varies with percentage of the gel. Other less frequently used progress markers are Cresol Red and Orange G which run at about 125 bp and 50 bp.

Percent agarose and resolution limits

Agarose gel electrophoresis can be used for the separation of DNA fragments ranging from 50 base pair to several megabases (millions of bases) using specialized apparatus. The distance between DNA bands of a given length is determined by the percent agarose in the gel. In general lower concentrations of agarose are better for larger molecules because they result in greater separation between bands that are close in size. The disadvantage of higher concentrations is the long run times (sometimes days). Instead high percentage agarose gels should be run with a pulsed field electrophoresis (PFE), or field inversion electrophoresis.

Most agarose gels are made with between 0.7% (good separation or resolution of large 5–10kb DNA fragments) and 2% (good resolution for small 0.2–1kb fragments) agarose dissolved in electrophoresis buffer. Some people go as high as 3% for separating very tiny fragments but a vertical polyacrylamide gel is more appropriate in this case. Low percentage gels are very weak and may break when you try to lift them. High percentage gels are often brittle and do not set evenly. 1% gels are common for many applications.

Buffers

There are a number of buffers used for agarose electrophoresis. The most common being: tris acetate EDTA (TAE), Tris/Borate/EDTA (TBE) and Sodium borate (SB). TAE has the lowest buffering capacity but provides the best resolution for larger DNA. This means a lower voltage and more time, but a better product. SB is relatively new and is ineffective in resolving fragments larger than 5 kbp; However, with its low conductivity, a much higher voltage could be used (up to 35 V/cm), which means a shorter analysis time for routine electrophoresis. As low as one base pair size difference could be resolved in 3% agarose gel with an extremely low conductivity medium (1 mM Lithium borate). [Brody JR, Calhoun ES, Gallmeier E, Creavalle TD, Kern SE (2004). Ultra-fast high-resolution agarose electrophoresis of DNA and RNA using low-molarity conductive media. Biotechniques. 37:598-602. [http://www.biotechniques.com/default.asp?page=article_archive&subsection=article_display&id=101200415&prevpage=article_archive] ]

Analysis

After electrophoresis the gel is illuminated with an ultraviolet lamp (usually by placing it on a light box, while using protective gear to limit exposure to ultraviolet radiation) to view the DNA bands. The ethidium bromide fluoresces reddish-orange in the presence of DNA. The DNA band can also be cut out of the gel, and can then be dissolved to retrieve the purified DNA.The gel can then be photographed usually with a digital or polaroid camera. Although the stained nucleic acid fluoresces reddish-orange, images are usually shown in black and white (see figures).

Gel electrophoresis research often takes advantage of software-based image analysis tools, such as ImageJ.

Typical method

Materials

Typically 10-30 μl/sample of the DNA fragments to separate are obtained, as well as a mixture of DNA fragments (usually 10-20) of known size (after processing with DNA size markers either from a commercial source or prepared manually).
* Buffer solution, usually TBE buffer or TAE 1.0x, pH 8.0
* AgaroseAn ultraviolet-fluorescent dye, ethidium bromide, (5.25 mg/ml in H2O). The stock solution be careful handling this.::Alternative dyes may be used, such as SYBR Green.
* Nitrile rubber gloves::Latex gloves do not protect well from ethidium bromide
* A color marker dye containing a low molecular weight dye such as "bromophenol blue" (to enable tracking the progress of the electrophoresis) and glycerol (to make the DNA solution more dense so it will sink into the wells of the gel).
* A gel rack
* A "comb"
* Power Supply
* UV lamp or UV lightbox or other method to visualize DNA in the gel

Preparation

There are several methods for preparing gels. A common example is shown here. Other methods might differ in the buffering system used, the sample size to be loaded, the total volume of the gel (typically thickness is kept to a constant amount while length and breadth are varied as needed). Most agarose gels used in modern biochemistry and molecular biology are prepared and run horizontally.

# Make a 1% agarose solution in 100ml TAE, for typical DNA fragments (see figures). A solution of up to 2-4% can be used if you analyze small DNA molecules, and for large molecules, a solution as low as 0.7% can be used.
# Carefully bring the solution just to the boil to dissolve the agarose, preferably in a microwave oven.
# Let the solution cool down to about 60 °C at room temperature, or water bath. Stir or swirl the solution while cooling.

"Wear gloves from here on, ethidium bromide is a mutagen, for more information on safety see ethidium bromide"

# Add 5 µl ethidium bromide stock (10 mg/ml) per 100 ml gel solution for a final concentration of 0.5 ug/ml. Be very careful when handling the concentrated stock. Some researchers prefer not to add ethidium bromide to the gel itself, instead soaking the gel in an ethidium bromide solution after running.
# Stir the solution to disperse the ethidium bromide, then pour it into the gel rack.
# Insert the comb at one side of the gel, about 5-10 mm from the end of the gel.
# When the gel has cooled down and become solid, carefully remove the comb. The holes that remain in the gel are the wells or slots.
# Put the gel, together with the rack, into a tank with TAE. Ethidium bromide at the same concentration can be added to the buffer. The gel must be completely covered with TAE, with the slots at the end electrode that will have the negative current.

Procedure

After the gel has been prepared, use a micropipette to inject about 2.5 µl of stained DNA (a DNA ladder is also highly recommended). Close the lid of the electrophoresis chamber and apply current (typically 100 V for 30 minutes with 15 ml of gel). The colored dye in the DNA ladder and DNA samples acts as a "front wave" that runs faster than the DNA itself. When the "front wave" approaches the end of the gel, the current is stopped. The DNA is stained with ethidium bromide, and is then visible under ultraviolet light.

#The agarose gel with three slots/wells (S).
#Injection of DNA ladder (molecular weight markers) into the first slot.
#DNA ladder injected. Injection of samples into the second and third slot.
#A current is applied. The DNA moves toward the positive anode due to the negative charges on its phosphate backbone.
#Small DNA strands move fast, large DNA strands move slowly through the gel. The DNA is not normally visible during this process, so the marker dye is added to the DNA to avoid the DNA being run entirely off the gel. The marker dye has a low molecular weight, and migrates faster than the DNA, so as long as the marker has not run past the end of the gel, the DNA will still be in the gel.
# Add the color marker dye to the DNA ladder.

References

See also

*gel electrophoresis
*SDS-polyacrylamide gel electrophoresis
*Southern blot
*Northern blot
*PCR
*Restriction endonuclease

External links

* [http://arbl.cvmbs.colostate.edu/hbooks/genetics/biotech/gels/index.html How to run a DNA or RNA gel]
* [http://arbl.cvmbs.colostate.edu/hbooks/genetics/biotech/gels/virgel.html Animation of gel analysis of DNA restriction fragments]
* [http://www.umd.umich.edu/labtv/modules/agarosegel/agarose.html Detailed description and movies of the preparation and uses of agarose gels]
* [http://web.mit.edu/7.02/virtual_lab/RDM/RDM1virtuallab.html Step by step photos of running a gel and extracting DNA]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • agarose gel electrophoresis — a type of gel electrophoresis with agarose as the support medium; used extensively to separate proteins, lipoproteins, nucleic acids, and other substances …   Medical dictionary

  • agarose gel electrophoresis — A method to separate DNA and RNA molecules on the basis of their size, in which samples are subjected to an electric field applied to a gel made with agarose …   Glossary of Biotechnology

  • Gel electrophoresis — apparatus – An agarose gel is placed in this buffer filled box and electrical field is applied via the power supply to the rear. The negative terminal is at the far end (black wire), so DNA migrates toward the camera. Classification… …   Wikipedia

  • Gel electrophoresis of nucleic acids — Digital printout of an agarose gel electrophoresis of cat insert plasmid DNA …   Wikipedia

  • Gel electrophoresis — electrophoresis electrophoresis n. 1. (Chem.) the motion of charged molecules or particles in a liquid medium under the influence of an electric field; particles with a positive charge move toward the cathode and negative to the anode. [WordNet… …   The Collaborative International Dictionary of English

  • Gel electrophoresis — The process in which molecules (such as proteins, DNA, or RNA fragments) can be separated according to size and electrical charge by applying an electric current to them while they are in a gel. The current forces the molecules through pores in a …   Medical dictionary

  • gel electrophoresis — noun : electrophoresis in which molecules (as proteins and nucleic acids) migrate through a gel and especially a polyacrylamide gel and separate into bands according to size * * * Biochem. a technique for separating protein molecules of varying… …   Useful english dictionary

  • Gel electrophoresis — Électrophorèse sur gel L électrophorèse sur gel est une variante de l électrophorèse de zones. Très utilisée en biochimie ou en biologie moléculaire, cette technique d électrophorèse permet de séparer des molécules en fonction de leur taille… …   Wikipédia en Français

  • gel electrophoresis — Biochem. a technique for separating protein molecules of varying sizes in a mixture by moving them through a block of gel, as of agarose or polyacrylamide, by means of an electric field, with smaller molecules moving faster and therefore farther… …   Universalium

  • Native Gel Electrophoresis — is a technique used mainly in protein electrophoresis where the proteins are not denatured and therefore separated based on their charge to mass ratio.The two main types of native gels used in protein electrophoresis are polyacrlylamide gels and… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”