Completion (oil and gas wells)

Completion (oil and gas wells)

In petroleum production, completion is the process of making a well ready for production (or injection). This principally involves preparing the bottom of the hole to the required specifications, running in the production tubing and its associated down hole tools as well as perforating and stimulating as required. Sometimes, the process of running in and cementing the casing is also included.

Contents

Lower completion

This refers to the portion of the well across the production or injection zone. The well designer has many tools and options available to design the lower completion according to the conditions of the reservoir. Typically, the lower completion is set across the productive zone using a liner hanger system, which anchors the lower completion to the production casing string. The broad categories of lower completion are listed below.

Barefoot completion

Selective isolation of oil, gas and barefoot section. Its an open hole, but with simple design and low cost. can be used in consolidated formations. It's the technique used by drilling companies in deep wells, Natural fractured reservoirs and Multilateral.

Open hole completion

This designation refers to a range of completions where no casing or liner is cemented in place across the production zone. In competent formations the zone might be left entirely bare, but usually some sort of sand-control and/or flow-control means are incorporated.

Openhole completions have seen significant uptake in recent years, and there are many configurations, often developed to address specific reservoir challenges. There have been many recent developments that have boosted the success of openhole completions, and they also tend to be popular in horizontal wells, where cemented installations are more expensive and technically more difficult. The common options for openhole completions are;

1) pre-holed liner (also often called pre-drilled liner). The liner is prepared with multiple small drilled holes, then set across the production zone to provide wellbore stability and an intervention conduit. Pre-holed liner is often combined with openhole packers, such as swelling elastomers, mechanical packers or external casing packers, to provide zonal segregation and isolation. It is now quite common to see a combination of pre-holed liner, solid liner and swelling elastomer packers to provide an initial isolation of unwanted water or gas zones. Multiple sliding sleeves can also be used in conjunction with openhole packers to provide considerable flexibility in zonal flow control for the life of the wellbore.

This type of completion is also being adopted in some water injection wells, although these require a much greater performance envelope for openhole packers, due to the considerable pressure and temperature changes that occur in water injectors.

Openhole completions (in comparison with cemented pipe) require better understanding of formation damage, wellbore clean-up and fluid loss control. A key difference is that perforating penetrates through the first 6-18 inches (15-45 cm) of formation around the wellbore, whilst openhole completions require the reservoir fluids to flow through all of the filtrate-invaded zone around the wellbore and lift-off of the mud filter cake.

Many openhole completions will incorporate fluid loss valves at the top of the liner to provide well control whilst the upper completion is run.

There are an increasing number of ideas coming into the market place to extend the options for openhole completions; for example, electronics can be used to actuate a self-opening or self-closing liner valve. This might be used in an openhole completion to improve clean-up, by bringing the well onto production from the toe-end for 100 days, then self-opening the heel-end. Inflow control devices and intelligent completions are also installed as openhole completions.

Pre-holed liner may provide some basic control of solids production, where the wellbore is thought to fail in aggregated chunks of rubble, but it is not typically regarded as a sand control completion.

2) Slotted liner can be selected as an alternative to pre-holed liner, sometimes as a personal preference or from established practice on a field. It can also be selected to provide a low cost control of sand/solids production. The slotted liner is machined with multiple longitudinal slots, for example 2 mm x 50mm, spread across the length and circumference of each joint. Recent advances in laser cutting means that slotting can now be done much cheaper to much smaller slot widths and in some situation slotted liner is now used for the same functionality as sand control screens.

3) Openhole sand control is selected where the liner is required to mechanically hold-back the movement of formation sand. There are many variants of openhole sand control, the three popular choices being stand-alone screens, openhole gravel packs (also known as external gravel packs, where a sized sand 'gravel' is placed as an annulus around the sand control screen) and expandable screens. Screen designs are mainly wire-wrap or premium; wire-wrap screens use spiral-welded corrosion-resistant wire wrapped around a drilled basepipe to provide a consistent small helical gap (such as 0.012-inch (0.30 mm), termed 12 gauge). Premium screens use a woven metal cloth wrapped around a basepipe. Expandable screens are run to depth before being mechanically swaged to a larger diameter. Ideally, expandable screens will be swaged until they contact the wellbore wall.

Cased hole completion

This involves running casing or a liner down through the production zone, and cementing it in place. Connection between the well bore and the formation is made by perforating. Because perforation intervals can be precisely positioned, this type of completion affords good control of fluid flow, although it relies on the quality of the cement to prevent fluid flow behind the liner. As such it is the most common form of completion...

Completion components

The upper completion refers to all components from the bottom of the production tubing upwards. Proper design of this "completion string" is essential to ensure the well can flow properly given the reservoir conditions and to permit any operations as are deemed necessary for enhancing production and safety.

Wellhead

This is the pressure containing equipment at the surface of the well where casing strings are suspended and the Blowout preventer or Christmas tree (oil well) is connected.

Christmas Tree

This is the main assembly of valves that controls flow from the well to the process plant (or the other way round for injection wells) and allows access for chemical squeezes[clarification needed (definition)] and well interventions.

Tubing hanger

This is the component, which sits on top of the wellhead and serves as the main support for the production tubing.

Production tubing

Production tubing is the main conduit for transporting hydrocarbons from the reservoir to surface (or injection material the other way). It runs from the tubing hanger at the top of the wellhead down to a point generally just above the top of the production zone.

Downhole safety valve

This component is intended as a last resort method of protecting the surface from the uncontrolled release of hydrocarbons. It is a cylindrical valve with either a ball or flapper closing mechanism. It is installed in the production tubing and is held in the open position by a high-pressure hydraulic line from surface contained in a 6.35 mm (1/4") control line that is attached to the DHSV's hydraulic chamber and terminated at surface to an hydraulic actuator. The high pressure is needed to overcome the production pressure in the tubing upstream of the choke on the tree. The valve will operate if the umbilical HP line is cut or the wellhead/tree is destroyed.

This valve allows fluids to pass up or be pumped down the production tubing. When closed the DHSV forms a barrier in the direction of hydrocarbon flow, but fluids can still be pumped down for well kill operations. It is placed as far below the surface as is deemed safe from any possible surface disturbance including cratering caused by the wipeout of the platform. Where hydrates are likely to form (most production is at risk of this), the depth of the SCSSV (surface-controlled sub-surface safety valve) below the seabed may be as much as 1 km: this will allow for the geothermal temperature to be high enough to prevent hydrates from blocking the valve.

Annular safety valve

On wells with gas lift capability, many operators consider it prudent to install a valve, which will isolate the 'A' annulus for the same reasons a DHSV may be needed to isolate the production tubing in order to prevent the inventory of natural gas downhole from becoming a hazard as it became on Piper Alpha.

Side pocket mandrel

This is a welded/machined product which contains a 'side-pocket' alongside the main tubular conduit. The side pocket, typically 1" or 1½" diameter is designed to contain gas lift valve, which allows hydrocarbon gas from the 'A' annulus to be injected into the flow stream.

Electrical submersible pump

This device is used for artificial lift to help provide energy to drive hydrocarbons to surface if reservoir pressure is insufficient.

Landing nipple

This is a receptacle to receive wireline tools. It is also a useful marker for depths in the well, which can be difficult to accurately determine. Normally it is set close to the end of the tubing string to be able to isolate the same from the reservoir conditions, at any time during the producing life of the well.

Sliding sleeve

The sliding sleeve is hydraulically or mechanically actuated to allow communication between the tubing and the 'A' annulus. They are often used in multiple reservoir wells to regulate flow to and from the zones.

Production packer

The packer isolates the annulus between the tubing and the inner casing and the foot of the well. This is to stop reservoir fluids from flowing up the full length of the casing and damaging it. It is generally placed close to the foot of the tubing, shortly above the production zone.

Downhole gauges

This is an electronic or fibre optic sensor to provide continuous monitoring of downhole pressure and temperature. Gauges use a 1/4" control line clamped onto the outside of the tubing string to provide an electrical or fibre optic communication to surface.

Perforated joint

This is a length of tubing with holes punched into it. If used, it will normally be positioned below the packer and will offer an alternative entry path for reservoir fluids into the tubing in case the shoe becomes blocked, for example, by a stuck perforation gun.

Formation isolation valve

This component, placed towards the foot of the completion string, is used to provide two way isolation from the formation for completion operations without the need for kill weight fluids. Their use is sporadic as they do not enjoy the best reputation for reliability when it comes to opening them at the end of the completion process.

Centralizer

In highly deviated wells, this components may be included towards the foot of the completion. It consists of a large collar, which keeps the completion string centralised within the hole.

Wireline entry guide

This component is often installed at the end of the tubing (the shoe). It is intended to make pulling out wireline tools easier by offering a guiding surface for the toolstring to re-enter the tubing without getting caught on the side of the shoe.

Perforating and stimulating

In cased hole completions (the majority of wells), once the completion string is in place, the final stage is to make a connection between the wellbore and the formation. This is done by running perforation guns to blast holes in the casing or liner to make a connection. Modern perforations are made using shaped explosive charges, similar to the armor-penetrating charge used on antitank rockets (bazookas).

Sometimes once the well is fully completed, further stimulation is necessary to achieve the planned productivity. There are a number of stimulation techniques.

Acidizing

This involves the injection of chemicals to eat away at any skin damage, "cleaning up" the formation, thereby improving the flow of reservoir fluids. Acid can also be used to clean the wellbore of some scales that form from mineral laden produced water.

Fracturing

This means creating and extending fractures from the perforation tunnels deeper into the formation, increasing the surface area for formation fluids to flow into the well, as well as extending past any possible damage near the wellbore. This may be done by injecting fluids at high pressure (hydraulic fracturing), injecting fluids laced with round granular material (proppant fracturing), or using explosives to generate a high pressure and high speed gas flow (TNT or PETN up to 1,900,000 psi (13,000,000 kPa) ) and (propellant stimulation up to 4,000 psi (28,000 kPa) ).

Acidising and fracturing (combined method)

This involves use of explosives and injection of chemicals to increase acid-rock contact.

Nitrogen circulation

Sometimes, productivity may be hampered due to the residue of completion fluids, heavy brines, in the wellbore. This is particularly a problem in gas wells. In these cases, coiled tubing may be used to pump nitrogen at high pressure into the bottom of the borehole to circulate out the brine.

See also


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • Chief Oil and Gas — Articleissues orphan = March 2008 refimprove = March 2008Infobox Company company name = Chief Oil and Gas company company type = Private foundation = 1994 location = Dallas, Texas, USA key people = Trevor Rees Jones, President and Chief Executive …   Wikipedia

  • Completion — may refer to: Completeness Completion (American football) Completion (oil and gas wells) one stage of Conveyancing, transfer of the title of property from one person to another In mathematics: Completion (metric space) Completion (order theory)… …   Wikipedia

  • Oil well — The pumpjack, such as this one located south of Midland, Texas, is a common sight in West Texas. An oil well is a general term for any boring through the earth s surface that is designed to find and acquire petroleum oil hydrocarbons. Usually… …   Wikipedia

  • Peak gas — Further information: Gas depletion and Hubbert peak theory Peak gas is the point in time at which the maximum global natural gas production rate is reached, after which the rate of production enters its terminal decline.[1] Natural gas… …   Wikipedia

  • Oil well control — is the management of the dangerous effects caused by unexpected high pressures upon surface equipment of oil or gas drilling rigs. Technically, oil well control involves preventing Formation fluid, usually referred to as kick, from entering into… …   Wikipedia

  • Oil platform — A typical offshore oil/gas platform. An oil platform, also referred to as an offshore platform or, somewhat incorrectly, oil rig, is a lаrge structure with facilities to drill wells, to extract and process oil and natural gas, and to temporarily… …   Wikipedia

  • Oil sands — The Athabasca oil sands in Alberta, Canada, are a very large source of bitumen, which can be upgraded to synthetic crude oil. Bituminous sands, colloquially known as oil sands or tar sands, are a type of unconventional petroleum deposit. The… …   Wikipedia

  • Oil shale — For the scientific technical journal, see Oil Shale (journal). Not to be confused with Shale oil or Tight oil. Oil shale Sedimentary Rock Combustion of oil shale Composition …   Wikipedia

  • Oil exploration in Puntland — Somalia This article is part of the series: Politics and government of Somalia Transitional Federal Charter E …   Wikipedia

  • Deepwater Horizon oil spill — 2010 oil spill and BP oil spill redirect here. For other oil spills in 2010, see 2010 oil spill (disambiguation). For the 2006 oil spill involving BP, see Prudhoe Bay oil spill. For the drilling rig and explosion, see Deepwater Horizon… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”