Foam Index

Foam Index

Foam Index Test is a rapid method to determine the relative levels of Air Entraining Agent (AEA) needed during concrete mixing, with or without mineral additives like combustion fly ash, that control air void volumes within cured concrete. [ [http://www.na.graceconstruction.com/custom/concrete/downloads/TB_0202.pdf Foam Index Test procedure] ] V.H. Dodson, Foam Index Test, Concrete Admixtures, Structural Engineering Series, Van Nostrand Reinhold, New York, pp 140–143 (1990).]

Introduction

AEA surfactants are added into concrete mixes to impart stable air microbubbles to give air void volumes between ~ 5%–10%. Besides increasing workability, adding the correct amount of AEA during concrete mixing improves its resistance to cracking during freeze and thaw cycles. Adding too much AEA during mixing decreases concrete strengths.

Fly ash from pulverized coal combustion is a typical mineral admixture utilized in the production of concrete, where it partially replaces cement and improves concrete workability, pumping characteristics, hardness and resistance to alkali attack. However, cement and components of fly ash adsorb AEA’s to different extents, making it more difficult to routinely impart the correct amount of entrained air into concrete. The Foam Index Test was developed to measure capacities of AEA for cement-mineral admixtures during concrete mixing.

The Foam Index Test is a laboratory titration procedure which determines the AEA absorption on fly ash or fly ash and cement mixtures. An AEA is titrated into a fly ash and cement suspension and the suspension is shaken. The added AEA leads to foam formation on top of the liquid surface, which initially behaves in an unstable manner. At the endpoint of the test, the AEA absorption sites are “saturated” and the AEA contributes to foam formation on the top of the mixture. The amount of AEA required to obtain stable foam depends on fly ash quality, fly ash-cement interactions, and characteristics of the AEA. Some fly ashes, typically those with high unburned carbon contents, [I. Kulaots, A. Hsu, R.H. Hurt and E.M. Suuberg, Adsorption of surfactants on unburned carbon in fly ash and development of a standardized foam index test, Cement & Concrete Research 33 (2003) 2091.] [Y-M. Gao, H-S. Shim, R.H. Hurt and R.M. Suuberg, Effects of carbon on air entrainment in fly ash concrete: the role of soot and carbon black, Energy & Fuels 11 (1997) 457.] [I. Külaots, R.H. Hurt and E.M. Suuberg, Size distribution of unburned carbon in coal fly ash and its implications, Fuel 83 (2004) 223.] tend to adsorb high amounts of AEA, i.e. more AEA is needed to obtain stable foam.

Procedure of foam index test

Adding diluted AEA one drop at a time is the most accurate way to measure the foam index, especially when trying to develop your ability to duplicate the test. You may want to add five drops at a time at first with a high dosage rate material until you get near the “Index” level. The traditional way to identify foam index values is by visual observation.

• A “Stable Foam” is achieved when no open areas of liquid show for at least 30–45 seconds on the surface of the foam. Bubbles break rapidly at AEA levels below the “Index” level. Bubbles will still break for several increments above the “Index” level as well … don’t continue adding AEA trying to stop the breaking bubbles. This point is difficult to judge at first. Run the same material several times in a row to help calibrate your “eye.”

• Although the Foam Index test is not designed to determine the actual AEA dosage amounts needed for concrete, it is possible to standardize procedures [http://www.worldofcoalash.org/2007/ashpdf/28stencel.pdf Automated foam index test] an automated instrument instead of manual test.] to determine AEA dosage amounts. It is also a good test to determine if specific materials will require more or less AEA relative to others. If the test is performed on the same materials and a plot of the results charted against required AEA dosages, correlations are possible between AEA dosage requirements and Foam Index test results.

Automated Foam Index Test(AFIT)

The AFIT instrument quantifies the dynamic foaming properties of air entraining agents, surfactants and foaming materials. It makes these measurements without intrusion of a probe or device into a working environment. Appropriate foam stabilities are necessary for proper performance of the materials onto/into which AEA’s or surfactants are applied. Stable foams have stable bubbles; unstable foams have breaking bubbles. When bubbles break they produce unique acoustic signatures, the dynamic properties of which are measured by the detectors incorporated into the AFIT instrument. The outcome is quantitative, repeatable foam index values and foaming measurements.

References

External links

* [http://www.acaa-usa.org/WorkInProgress/taskgroups.htm ACAA Foam Index Task Group]

* [http://www.fhwa.dot.gov/pavement/concrete/pubs/06080/appe.cfm Draft Standard Test Method for Determining Foam Index of Cementitious Paste Mixtures]

* [http://www.triboflow.com/tech/products.html Automated Foam Index Test Instrument]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Foam (organization) — FoAM [ [http://fo.am f o a m ] ] describes itself as a laboratory for the propagation of lived and living experience. [ [http://fo.am/trg/bxl.html f o a m ] ] The networked, Brussels based collective constitutes a group of designers, scientists,… …   Wikipedia

  • Foam hand — A foam hand, also known as a foam finger, is a sports paraphernalia item worn on the hand to show support for a particular team. The most common version resembles an oversized hand with an extended index finger. Usually the surface displays a… …   Wikipedia

  • Foam Lake No. 276, Saskatchewan — Infobox Settlement official name = Foam Lake No. 276, Saskatchewan other name = native name = nickname = settlement type = motto = imagesize = image caption = flag size = image seal size = image shield = shield size = city logo = citylogo size =… …   Wikipedia

  • Foam weapon — A foam weapon, (also known as a boffer or latex weapon ), is a padded weapon used for simulated combat. Such weapons are typically used in live action role playing games. TerminologyIn the United States the term boffer is used for all foam… …   Wikipedia

  • Hot-wire foam cutter — A hot wire foam cutter is a tool used to cut polystyrene foam and similar materials. The device consists of a thin, taut metal wire, often made of nichrome or stainless steel, or a thicker wire preformed into a desired shape, which is heated via… …   Wikipedia

  • Concrete — This article is about the construction material. For other uses, see Concrete (disambiguation). Outer view of the Roman Pantheon, still the largest unreinforced solid concrete dome.[1] …   Wikipedia

  • AEA — or Aea may refer to: * Autoerotic asphyxiation, a sexual act * Actors Equity Association, a U.S. labor union * Advanced Electronics Applications, a company that sells amateur radio specialty equipment * Advanced Extension Award of the British… …   Wikipedia

  • FSI — foam stability index; Food Sanitation Institute; functional status index …   Medical dictionary

  • FSI — • foam stability index; • Food Sanitation Institute; • functional status index …   Dictionary of medical acronyms & abbreviations

  • NASA spin-off — Science and technology in the United States African American contributions Discoveries …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”