Plasma cutting

Plasma cutting

: "This article is about the common manufacturing process. For various fictional weapons, see plasma rifle and directed-energy weapon."

Plasma cutting is a process that is used to cut steel and other metals (or sometimes other materials) using a plasma torch. In this process, an inert gas (in some units, compressed air) is blown at high speed out of a nozzle; at the same time an electrical arc is formed through that gas from the nozzle to the surface being cut, turning some of that gas to plasma. The plasma is sufficiently hot to melt the metal being cut and moves sufficiently fast to blow molten metal away from the cut. Plasma can also be used for plasma arc welding and other applications.

Process

The HF Contact type typically found in budget machines uses a high-frequency, high-voltage spark to ionise the air through the torch head and initiate an arc. The arc can only be formed if the torch is in contact with the job material. HF Contact type machines are not suitable for applications involving CNC cutting.

The Pilot Arc type uses a two cycle approach to producing plasma. First, a high-voltage, low current circuit is used to initialize a very small high-intensity spark within the torch body, thereby generating a small pocket of plasma gas. This is referred to as the "pilot arc". The pilot arc has a return electrical path built into the torch head. The pilot arc will maintain itself until it is brought into proximity of the workpiece where it ignites the main plasma cutting arc. Plasma arcs are extremely hot and are in the range of 15,000 degrees Celsius.

Plasma is an effective means of cutting thin and thick materials alike. Hand-held torches can usually cut up to 2 in (48 mm) thick steel plate, and stronger computer-controlled torches can pierce and cut steel up to 12 inches (300 mm) thick. Formerly, plasma cutters could only work on conductive materials; however, new technologies allow the plasma ignition arc to be enclosed within the nozzle, thus allowing the cutter to be used for non-conductive workpieces.

Since plasma cutters produce a very hot and very localized "cone" to cut with, they are extremely useful for cutting sheet metal in curved or angled shapes.

tarting methods

Plasma cutters use a number of methods to start the pilot arc, depending on the environment the unit is to be used in and its age. Older cutters use a high voltage, high frequency circuit to start the arc. This method has a number of disadvantages, including risk of electrocution, difficulty of repair, sparkgap maintenance, and the large amount of radio frequency emissions. Plasma cutters working near sensitive electronics, such as CNC hardware or computers, use the contact start method. The nozzle and electrode are in contact. The nozzle is the cathode, and the electrode is the anode. When the plasma gas begins to flow, the nozzle is blown forward. A third, less common method is capacitive discharge into the primary circuit via a Silicon Controlled Rectifier.

Inverter plasma cutters

Analog plasma cutters, typically requiring more than 2 kilowatts, use a heavy mains-frequency transformer. Inverter plasma cutters rectify the mains voltage into DC, which is fed into either an IGBT or a MOSFET. With paralleled MOSFET transistors if one of the transistors activates prematurely it can lead to a cascading failure of one quarter of the inverter. Later invention, IGBT transistors when not used in this paralleled fasion will not blow out that easily. IGBTs can be generally found in high current machines where it is not possible to parallel sufficient MOSFET transistors. Switching frequency used ranges from about 10kHz to about 200kHz, depending on the ability of the switching transistors and rectifiers; higher switching frequency greatly reduces the magnetic flux in the step down transformer, and therefore the size of the transformer is reduced accordingly. The switch mode topology is referred to as a dual transistor off-line forward converter. Although lighter and more powerful, some inverter plasma cutters, especially those without power factor correction, cannot be run from a generator (that means manufacturer of the inverter unit forbids to do so; it is only valid for small, light portable generators). However newer models have internal circuitry that allow units without power factor correction to run on light power generators.

Plasma gouging

Plasma gouging is a related process, typically performed on the same equipment as plasma cutting. Instead of cutting the material, plasma gouging uses a different torch configuration (torch nozzles and gas diffusers are usually different), and a longer torch-to-workpiece distance, to blow away metal. Plasma gouging can be used in a variety of applications, including removing a weld for rework. The additional sparks generated by the process requires the operator to wear a leather shield protecting their hand and forearm. Torch leads also can be protected by a leather sheath.

CNC cutting methods

Plasma cutters have also been used in CNC (computer numerically controlled) machinery. Manufacturers build CNC cutting tables, some with the cutter built in to the table. The idea behind CNC tables is to allow a computer to control the torch head making clean sharp cuts. Modern CNC plasma equipment is capable of multi-axis cutting of thick material, allowing opportunities for complex welding seams on CNC welding equipment that is not possible otherwise. For thinner material cutting, plasma cutting is being progressively replaced by laser cutting, due mainly to the laser cutter's superior hole-cutting abilities.

A specialized use of CNC Plasma Cutters has been in the HVAC industry. Software will process information on ductwork and create flat patterns to be cut on the cutting table by the plasma torch. This technology has enormously increased productivity within the industry since its introduction in the early 1980s.

New technology

In the past decade plasma torch manufacturers have engineered new models with a smaller nozzle and a thinner plasma arc. This allows near laser quality on plasma cut edges. Several manufacturers have combined precision CNC control with these torches to allow fabricators to produce parts that require little or no finishing.

Costs

Plasma torches were once quite expensive, usually at least a thousand U.S. dollars. For this reason they were usually only found in professional welding shops and very well-stocked private garages and shops. However, modern plasma torches are becoming cheaper, and now are within the price range of many hobbyists. Older units may be very heavy, but still portable, while some newer ones with inverter technology weigh only a few pounds yet equal or exceed the capacities of older ones.

ee also

*Plasma arc welding
*Water jet cutter

External links

* [http://science.howstuffworks.com/plasma-cutter1.htm HowStuffWorks on plasma cutting]
* [http://www.safetyculture.com.au/procedures/plasma_cutter_procedure.php Plasma Cutter Safe Work Method Statement]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • plasma cutting — Смотри плазменная резка …   Энциклопедический словарь по металлургии

  • Hypertherm Plasma Cutting — is an American corporation which designs and manufactures metal cutting systems for use in a variety of industries such as shipbuilding, manufacturing, and automotive repair. It makes handheld and mechanized plasma cutters and consumables, as… …   Wikipedia

  • Plasma rifle — TOCrightPlasma rifles are theoretical weapons often used in science fiction. They are, in effect, a type of raygun. Plasma weapons use a small nuclear reactor or fuel cell or other type of advanced energy storage device to power an… …   Wikipedia

  • Plasma torch — A plasma torch (or plasma arc or plasma gun) is a device that generates a directed flow of plasma from its nozzle. The plasma jet can be used for: *Plasma cutting. *Plasma spraying. *Plasma arc waste disposal, which reduces waste to power… …   Wikipedia

  • Plasma arc welding — (PAW) is an arc welding process similar to gas tungsten arc welding (GTAW). The electric arc is formed between an electrode (which is usually but not always made of sintered tungsten) and the workpiece. The key difference from GTAW is that in PAW …   Wikipedia

  • Plasma nitriding — or ion nitriding (sometimes also called plasma ion nitriding) or glow discharge nitriding, is an industrial surface hardening treatment for metallic materials.DescriptionA plasma is the fourth state of matter, the other three being solid, liquid… …   Wikipedia

  • Plasma-arc cutting — Plasma arc cutting. См. Плазменно дуговая резка. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • plasma arc cutters — Cutting equipment that makes clean, fast cuts without destroying the properties of high strength steels …   Dictionary of automotive terms

  • Plasma (physics) — For other uses, see Plasma. Plasma lamp, illustrating some of the more complex phenomena of a plasma, including filamentation. The colors are a result of relaxation of electrons in excited states to lower energy states after they have recombined… …   Wikipedia

  • Cutting — For other uses, see Cutting (disambiguation). Different types of scissors sewing (left), paper (middle), kitchen (right) Cutting is the separation of a physical object, or a portion of a physical object, into two portions, through the application …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”