Frequency compensation

Frequency compensation

In electrical engineering, frequency compensation is a technique used in amplifiers, and especially in amplifiers employing negative feedback. It usually has two primary goals: To avoid the unintentional creation of positive feedback, which will cause the amplifier to oscillate, and to control overshoot and ringing in the amplifier's step response.

Explanation

Most amplifiers use negative feedback to trade gain for other desirable properties, such as decreased distortion or improved noise reduction. Ideally, the phase characteristic of an amplifier's frequency response would be constant; however, device limitations make this goal physically unattainable. More particularly, capacitances within the amplifier's gain stages cause the output signal to lag behind the input signal by 90° for each pole they create. [In this context, a pole is the point in a frequency response curve where the amplitude decreases by 3db due to an integrating resistance and capacitive reactance. Ultimately, each pole will result in a phase lag of 90°, i.e., the output signal will lag "behind" the input signal by 90° at this point. For the mathematical concept of a pole, see, Pole (complex analysis).] If the sum of these phase lags reaches 360°, the output signal will be in phase with the input signal. Feeding back any portion of this output signal to the input when the gain of the amplifier is sufficient will cause the amplifier to oscillate. This is because the feedback signal will reinforce the input signal. That is, the feedback is then positive rather than negative.

Frequency compensation is implemented to avoid this result.

Another goal of frequency compensation is to control the step response of an amplifier circuit as shown in Figure 1. For example, if a step in voltage is input to a voltage amplifier, ideally a step in output voltage would occur. However, the output is not ideal because of the frequency response of the amplifier, and ringing occurs. Several figures of merit to describe the adequacy of step response are in common use. One is the rise time of the output, which ideally would be short. A second is the time for the output to lock into its final value, which again should be short. The success in reaching this lock-in at final value is described by overshoot (how far the response exceeds final value) and settling time (how long the output swings back and forth about its final value). These various measures of the step response usually conflict with one another, requiring optimization methods.

Frequency compensation is implemented to optimize step response, one method being pole splitting.

Use in operational amplifiers

Because operational amplifiers are so ubiquitous and are designed to be used with feedback, the following discussion will be limited to frequency compensation of these devices.

It should be expected that the outputs of even the simplest operational amplifiers will have at least two poles. An unfortunate consequence of this is that at some critical frequency, the phase of the amplifier's output = -180° compared to the phase of its input signal. The amplifier will oscillate if it has a gain of one or more at this critical frequency. This is because (a) the feedback is implemented through the use of an inverting input that adds an additional -180° to the output phase making the total phase shift -360° and (b) the gain is sufficient to induce oscillation.

A more precise statement of this is the following: An operational amplifier will oscillate at the frequency at which its open loop gain equals its closed loop gain if, at that frequency,

:1. The open loop gain of the amplifier is ≥ 1 and

:2. The difference between the phase of the open loop signal and phase response of the network creating the closed loop output = -180°. Mathematically,

::" ΦOL – ΦCLnet = -180° "

Practice

Frequency compensation is implemented by modifying the gain and phase characteristics of the amplifier's open loop output or of its feedback network, or both, in such a way as to avoid the conditions leading to oscillation. This is usually done by the internal or external use of resistance-capacitance networks.

Dominant-pole compensation

The method most commonly used is called dominant-pole compensation, which is a form of lag compensation. A pole placed at an appropriate low frequency in the open-loop response reduces the gain of the amplifier to one (0 dB) for a frequency at or just below the location of the next highest frequency pole. The lowest frequency pole is called the dominant pole because it dominates the effect of all of the higher frequency poles. The result is that the difference between the open loop output phase and the phase response of a feedback network having no reactive elements never falls below −180° while the amplifier has a gain of one or more, ensuring stability.

Dominant-pole compensation can be implemented for general purpose operational amplifiers by adding an integrating capacitance to the stage that provides the bulk of the amplifier's gain. This capacitor creates a pole that is set at a frequency low enough to reduce the gain to one (0 dB) at or just below the frequency where the pole next highest in frequency is located. The result is a phase margin of ≈ 45°, depending on the proximity of still higher poles. [ The dominant pole produces a phase shift approximating -90° from approx. 10 times the pole frequency to a frequency a factor of ten below the next higher pole position. The next higher pole, in turn, adds another -45° for a frequency at its location for a total of -135° (neglecting the still higher poles).] This margin is sufficient to prevent oscillation in the most commonly used feedback configurations. In addition, dominant-pole compensation allows control of overshoot and ringing in the amplifier step response, which can be a more demanding requirement than the simple need for stability.

Though simple and effective, this kind of conservative dominant pole compensation has two drawbacks:

:1. It reduces the bandwidth of the amplifier, thereby reducing available open loop gain at higher frequencies. This, in turn, reduces the amount of feedback available for distortion correction, etc. at higher frequencies.

:2. It reduces the amplifier's slew rate. This reduction results from the time it takes the finite current driving the compensated stage to charge the compensating capacitor. The result is the inability of the amplifier to reproduce high amplitude, rapidly changing signals accurately.

Other methods

Other compensation methods are pole-splitting compensation, lead compensation, lead-lag compensation and feed-forward compensation.

:Pole splitting compensation. This method moves the lowest frequency pole to an even lower frequency and the higher frequency pole to a higher frequency.

:Lead compensation. Whereas lag compensation and pole splitting compensation place or move poles in the open loop response, lead compensation places a zero [In this context, a zero is the point in a frequency response curve where the amplitude increases by 3db due to a differentiating resistance and capacitive reactance. Ultimately, each zero will result in a phase lead of 90°, i.e., the phase of the output signal will be 90° "ahead" of the phase of the input signal at this point. For the mathematical concept of a zero, see, Zero (complex analysis).] in the open loop response to cancel one of the existing poles.

:Lead-lag compensation places both a zero and a pole in the open loop response, with the pole usually being at an open loop gain of less than one.

:Feed-forward compensation uses a capacitor to bypass a stage in the amplifier at high frequencies, thereby eliminating the pole that stage creates.

The purpose of the latter three of these methods is to allow greater open loop bandwidth while still maintaining amplifier closed loop stability. They are often used to compensate high gain, wide bandwidth amplifiers.

Footnotes

ee also

* Pole splitting
* Bode plot
* Negative feedback amplifier
* Step response


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • frequency-compensation capacitor — dažninės pataisos kondensatorius statusas T sritis radioelektronika atitikmenys: angl. frequency compensation capacitor vok. frequenzkompensierter Kondensator, m rus. конденсатор для частотной компенсации, m pranc. condensateur à compensation de… …   Radioelektronikos terminų žodynas

  • Compensation (engineering) — In engineering, compensation is planning for side effects or other unintended issues in a design. The design of an invention can itself also be to compensate for some other existing issue or exception. One example is in a voltage controlled… …   Wikipedia

  • Frequency multiplier — A frequency multiplier is commonly used in a radio receiver or radio transmitter to multiply the base frequency of the oscillator by a predetermined number. This multiplied frequency is then amplified and sent to the final drive stage and into… …   Wikipedia

  • condensateur à compensation de fréquence — dažninės pataisos kondensatorius statusas T sritis radioelektronika atitikmenys: angl. frequency compensation capacitor vok. frequenzkompensierter Kondensator, m rus. конденсатор для частотной компенсации, m pranc. condensateur à compensation de… …   Radioelektronikos terminų žodynas

  • Reproductive compensation — was originally a theory to explain why recessive genetic disorders may persist in a population. It was proposed in 1967 as an explanation for the maintenance of Rh negative blood groups. [cite journal| author=Levin, BR| journal=American Journal… …   Wikipedia

  • Risk compensation — In ethology, risk compensation is an effect whereby individual people may tend to adjust their behavior in response to perceived changes in risk. It is seen as self evident that individuals will tend to behave in a more cautious manner if their… …   Wikipedia

  • Motion compensation — is an algorithmic technique employed in the encoding of video data for video compression, for example in the generation of MPEG 2 files. Motion compensation describes a picture in terms of the transformation of a reference picture to the current… …   Wikipedia

  • Superconducting Radio Frequency — (SRF) science and technology involves the application of electrical superconductors to radio frequency devices. The ultra low electrical loss of the superconductor yields RF resonators with extremely high quality factors, or Q . For example, it… …   Wikipedia

  • Variable frequency transformer — A variable frequency transformer is used to transmit electricity between two asynchronous alternating current domains. The VFT is a relatively recent development (first deployed in 2004). Most grid interties use high voltage direct current… …   Wikipedia

  • Operational amplifier — A Signetics μa741 operational amplifier, one of the most successful op amps. An operational amplifier ( op amp ) is a DC coupled high gain electronic voltage amplifier with a differential input and, usually, a single ended output.[1] An op amp… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”