Suspension bridge

:"This article is concerned with a particular type of suspension bridge, the suspended-deck type.:For an index to the several types see suspension bridge types.:For the Gladiators event, see Suspension Bridge (Gladiators)."

A suspension bridge is a type of bridge where the main load-bearing elements are hung from suspension cables. While modern suspension bridges with level decks date from the early 19th century, earlier types are reported from the 3rd century BC. Simple suspension bridges, for use by pedestrians and livestock, are still constructed, based upon the ancient Inca rope bridge.

Suspended well from two high locations over a river or canyon, simple suspension bridges follow a shallow downward arc and are not suited for modern roads and railroads. Advances in materials and design led to the development of the suspended-deck suspension bridge, a modern bridge capable of carrying vehicles and light rail. Instead of the deck following the downward arc of the main load-bearing cables (or chains), these cables are suspended between towers, and vertical "suspender cables" carry the weight of the deck below, upon which traffic crosses. This arrangement allows the deck to be level or to arc slightly upward for additional clearance.

The suspension cables must be anchored at each end of the bridge, since any load applied to the bridge is transformed into a tension in these main cables. The main cables continue beyond the pillars to deck-level supports, and further continue to connections with anchors in the ground. The roadway is supported by vertical suspender cables or rods, called hangers. In some circumstances the towers may sit on a bluff or canyon edge where the road may proceed directly to the main span, otherwise the bridge will usually have two smaller spans, running between either pair of pillars and the highway, which may be supported by suspender cables or may use a truss bridge to make this connection. In the latter case there will be very little arc in the outboard main cables.


The suspension bridge is one of the oldest types of bridge. Early simple, or catenary, suspension bridges consisted of three or more cables made from vines, where people walked directly on the ropes to cross. Simple suspension bridges with decking made from planks resting on two cables date back at least to 285BC in China, and other bridges of similar type are recorded in Tibet. Seven bridges of this type were reportedly built in China in 95BC at Chengdu by Li Bing. A Chinese multi-span simple suspension bridge with bamboo cables is reported at Quan-Xian, documented from 960AD and possibly dating back to the 3rd century BC.

Simple suspension bridges using iron chains are also documented in China and the Himalayas, although their earliest date is unclear. One example, the Luding Bridge, dates from 1703, spanning 100 m using eleven iron chains. Several are attributed to Tibetan monk Thang-stong rGyal-po, who reportedly built several in Tibet and Bhutan in the 15th century, including one at Chuka. Claims that more modern suspension bridges with a horizontal deck also originated in Tibet or China remain largely unsubstantiated.The first design for a bridge resembling the modern suspension bridge in the West is attributed to Faust Vrančić, whose 1595 book "“Machinae Novae”" included drawings both for a timber and rope suspension bridge, and a hybrid suspension and cable-stayed bridge using iron chains. However, the first such bridge actually built was James Finley’s iron chain bridge at Jacob’s Creek, in Pennsylvania, in 1801. This was widely publicised from 1810 onwards, beginning a period of rapid development of the modern suspension bridge.

Early British chain bridges included the Dryburgh Abbey Bridge (1817) and 137 m Union Bridge (1820), with spans rapidly increasing to 176 m with the Menai Suspension Bridge (1826). The Clifton Suspension Bridge shown above (designed in 1831, completed in 1864 with a 214 m central span) is one of the longest of the parabolic arc chain type.

Development of wire cable suspension bridges dates to the temporary simple suspension bridge at Annonay built by Marc Seguin and his brothers in 1822. It spanned only 18 m. The first permanent wire cable suspension bridge was Guillaume Henri Dufour’s Saint Antoine Bridge in Geneva of 1823, with two 40 m spans. The first with cables assembled in mid-air in the modern method was Joseph Chaley’s Grand Pont Suspendu in Fribourg, in 1834.

tructural behavior

tructural analysis

The main forces in a suspension bridge are tension in the main cables and compression in the pillars. Since almost all the force on the pillars is vertically downwards and they are also stabilized by the main cables, the pillars can be made quite slender, as on the Severn Bridge, near Bristol, England.
wide image|Suspension bridge-panoramic.jpg|693px|
The slender lines of the Severn Bridge

In a suspension bridge, cables which are suspended via towers which support them hold up the road deck. The weight is transferred by the cables to the towers, which then in turn transfer the weight to the ground.

Assuming a negligible weight as compared to the weight of the deck and vehicles being supported, a suspension bridge’s main cables will form a parabola (very similar to a catenary, the form the unloaded cables take before the deck is added). This can be seen from the cable’s constant gradient increase with linear (deck) distance, this increase in gradient at each connection with the deck providing a net upward support force. Combined with the relatively simple constraints placed upon the actual deck, this makes the suspension bridge much simpler to design and analyze than a cable-stayed bridge, where the deck is in compression.

Disadvantages compared with other bridge types

*Considerable stiffness or aerodynamic profiling may be required to prevent the bridge deck vibrating under high winds
*The relatively low deck stiffness compared to other types makes it more difficult to carry heavy rail traffic where high concentrated live loads occur
*Some access below may be required during construction, to lift the initial cables or to lift deck units. This access can often be avoided in cable-stayed bridge construction


Underspanned suspension bridge

In an underspanned suspension bridge, the main cables hang entirely below the bridge deck, but are still anchored into the ground in a similar way to the conventional type. Very few bridges of this nature have been built, as the deck is inherently less stable than when suspended below the cables. Examples include the Pont des Bergues of 1834 designed by Guillaume Henri DufourPeters, Tom F., "“Transitions in Engineering: Guillaume Henri Dufour and the Early 19th Century Cable Suspension Bridges”", Birkhauser, 1987, ISBN 3764319291] ; James Smith’s Micklewood BridgeDrewry, Charles Stewart, "“Memoir on Suspension Bridges”", Longman, Rees, Orme, Brown, Green & Longman, London, 1832] ; and a proposal by Robert Stevenson for a bridge over the River Almond near Edinburgh.

uspension cable types

The main suspension cable in older bridges was often made from chain or linked bars, but modern bridge cables are made from multiple strands of wire. This is for greater redundancy; a few flawed strands in the hundreds used pose very little threat, whereas a single bad link or eyebar can cause failure of the entire bridge. (The failure of a single eyebar was found to be the cause of the collapse of the Silver Bridge over the Ohio river). Another reason is that as spans increased, engineers were unable to lift larger chains into position, whereas wire strand cables can be largely prepared in mid-air.

Deck structure types

Most suspension bridges have open truss structures to support the roadbed (particularly owing to the unfavorable effects of using plate girders, discovered from the Tacoma Narrows bridge collapse). Recent developments in bridge aerodynamics have allowed the re-introduction of plate structures. In the illustration to the right, note the very sharp entry edge and sloping undergirders in the suspension bridge shown. This enables this type of construction to be used without the danger of vortex shedding and consequent aeroelastic effects, such as those that destroyed the Tacoma Narrows Bridge.

Use other than road and rail

The principles of suspension used on the large scale may also appear in contexts less dramatic than road or rail bridges. Light cable suspension may prove less expensive and seem more elegant for a footbridge than strong girder supports. Where such a bridge spans a gap between two buildings, there is no need to construct special towers, as the buildings can anchor the cables. Cable suspension may also be augmented by the inherent stiffness of a structure that has much in common with a Tubular bridge.

Construction sequence (wire strand cable type)

*Where the towers are founded on underwater piers, "caissons" are sunk and any soft bottom is excavated for a foundation. If the bedrock is too deep to be exposed by excavation or the sinking of a caisson, pilings are driven to the bedrock or into overlying hard soil, or a large concrete pad to distribute the weight over less resistant soil may be constructed, first preparing the surface with a bed of compacted gravel. (Such a pad footing can also accommodate the movements of an active earthquake fault, and this has been implemented on the foundations of the cable-stayed Rio-Antirio bridge. The foundation piers are then extended to above water level.
*Where the towers are founded on dry land, deep foundation excavation or pilings are used.
*From the tower foundation, towers of single or multiple columns are erected using concrete, stonework, or steel structures. At some elevation there must be a passage for the deck, with the columns extending high above this level.
*Smooth open cable paths called "saddles" are anchored atop the towers. These allow for slight movements of the cable as the loads change during construction. The top of these saddles may be closed with an additional part after completion of the bridge.
*"Anchorages" are constructed to resist the tension of the cables. These are usually anchored in good quality rock, but may consist of massive reinforced concrete deadweights within an excavation. The anchorage structure will have multiple protruding open "eyebolts" enclosed within a secure space.
*A temporary suspended walkway supported by wire rope follows the curve of the cables to be constructed, mathematically described as a catenary arc.
*Another set of wire ropes are suspended above the walkway and are used to support a "traveler" that has wheels riding atop these cables. There will be one set of wire ropes and a traveler for each cable to be “spun”.
*Pulling cables attached to winches are capable of pulling the traveler from one anchorage to the other, traveling in arcs to the tops of the two towers.
*High strength wire, typically less than 10 mm in diameter, is pulled in a loop by pulleys on the traveler, with one end affixed at an anchorage. Workers stationed along the walkway attach the passing cable to a bundle with a temporary binding. When the traveler reaches the opposite anchorage the loop is placed over an open anchor eyebar.
*The traveler is returned to the start point to pick up another loop or it is used to carry a new loop from this side.
*As loops are placed, corrosion proofing may be applied.
*In this way a complete sub-cable is created linking the eyebar (or a set of eyebars) from one anchorage to the other. The sub-cables will have a hexagonal cross section and are held together with the temporary bindings.
*Multiple adjacent sub-cables are placed adjacent to each other. While these are on a hexagonal grid, the general form for the larger cable is circular.
*The entire cable is then compressed by a traveling hydraulic press into a closely packed cylinder and tightly wrapped with additional wire to form the final circular cross section.
*"Saddles" to carry the suspender cables are clamped to the main cables, each with an appropriate shape to conform to the ultimate slope of the main cables. Each saddle is an equal horizontal distance from the next, with spacing appropriate to the design of the deck.
*"Suspender cables" engineered and cut to precise lengths and carrying swedged ends are looped over the saddles. In some bridges, where the towers are close to or on the shore, the suspender cables may be applied only to the central span.
*Special lifting hosts attached to the suspenders or from the main cables are used to lift prefabricated sections of bridge deck to the proper level, provided that the local conditions allow the sections to be carried below the bridge by barge or other means, otherwise a traveling cantilever may be used to extend the deck one section at a time. If the addition of the deck structure extends from the towers the finished portions of the deck will pitch upward rather sharply, as there is no downward force in the center of the span. Upon completion of the deck the added load will pull the main cables into an arc mathematically described as a parabola, while the arc of the deck will be as the designer intended — usually a gentle upward arc for added clearance if over a shipping channel, or flat in other cases such as a span over a canyon.
*With completion of the primary structure various details such as lighting, handrails, finish painting and paving are added.

The longest suspension bridge spans in the world

Suspension bridge are typically ranked by the length of their main span.
#Akashi-Kaikyo Bridge (Japan), 1991 m — 1998
#Xihoumen Bridge (China), 1650 m — 2007
#Great Belt Bridge (Denmark), 1624 m — 1998
#Runyang Bridge (China), 1490 m — 2005
#Humber Bridge (England, United Kingdom), 1410 m — 1981. (The longest span from 1981 until 1998.)
#Jiangyin Suspension Bridge (China), 1385 m — 1997
#Tsing Ma Bridge (China), 1377 m — 1997 (longest span with both road and metro)
#Verrazano Narrows Bridge (USA), 1298 m — 1964. (The longest span from 1964 until 1981.)
#Golden Gate Bridge (USA), 1280 m — 1937. (The longest span from 1937 until 1964.)
#Yangluo Bridge (China), 1280 m — 2007

Other suspension bridges

"See also: History of longest vehicle suspension bridge spans."
*Union Bridge (England/Scotland), 137 m — 1820. The longest span from 1820 to 1826. The oldest in the world still in use today.
*Brooklyn Bridge (1883). The first steel-wire suspension bridge.
*Bear Mountain Bridge (USA), 497 m — 1924. The longest span from 1924 to 1926. The first suspension bridge to have a concrete deck. The construction methods pioneered in building it would make possible several much larger projects to follow.
*Royal Gorge Bridge (USA) 1929 The highest (384 m) suspension bridge in the world.
*San Francisco – Oakland Bay Bridge (California, USA), 704 m — 1936. The western portion is two complete two tower bridges end-to-end with a central anchorage, required to avoid dynamic interactions between three main spans between the four towers. Until recently, this was the longest steel high-level bridge in the world. [cite web
title=Symphonies in Steel: Bay Bridge and the Golden Gate
publisher=Virtual Museum of the City of San Francisco
] The eastern portion (a cantilever bridge) is being replaced with a self-anchored suspension bridge which will be the longest of its type in the world.
*Tacoma Narrows Bridge (USA), 853 m — 1950 & 2007. The largest twin suspension bridge in the world.

Infamous suspension bridges

*The Bridge of San Luis Rey (Fictional)
*Silver Bridge, a 1928 eyebar chain bridge that collapsed in 1967, killing forty-six people.
* Tacoma Narrows Bridge, (USA), 853 m — 1940. The Tacoma Narrows was prone to sustained and moderately strong winds. This was due to a phenomenon called aeroelastic fluttering (owing to its unique plate-girder deck structure and ultimately its nickname “The Galloping Gertie”). This led to its collapse only months after completion. The collapse was captured on film.

=Picture Gallery=


ee also

* — for articles about specific suspension bridges.
* List of longest suspension bridge spans
* Timeline of three longest spans whether bridge, aerial tramway, powerline, ceiling or dome etc.
* Cable-stayed bridge — superficially similar to a suspension bridge, but cables from the towers directly support the roadway, rather than the road being suspended indirectly by additional cables from the main cables connecting two towers.
* Inca rope bridge — has features in common with a suspension bridge and predates them by at least three hundred years. However in a rope bridge the deck itself is suspended from the anchored piers and the guardrails are non-structural.
* Self-supporting suspension bridge — combining elements of a suspension bridge and a cable-stayed bridge.
* Simple suspension bridge — a modern implementation of the rope bridge using steel cables, although either the upper guardrail or lower footboard cables may be the main structural cables.

External links

* [ New Brunswick Canada suspension footbridges]
* [ Structurae: suspension bridges]
* [ American Society of Civil Engineers] History and heritage of civil engineering — bridges
* [ Bridgemeister: Mostly suspension bridges]
*cite web
url= Inca suspension bridges
title=How the Inca Leapt Canyons
publisher=The New York Times
first=John Noble
date=May 8, 2007

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Suspension bridge — Suspension Sus*pen sion, n. [Cf. F. suspension, L. suspensio arched work, imperfect pronunciation. See {Suspend}.] 1. The act of suspending, or the state of being suspended; pendency; as, suspension from a hook. [1913 Webster] 2. Especially,… …   The Collaborative International Dictionary of English

  • Suspension bridge — Bridge Bridge (br[i^]j), n. [OE. brig, brigge, brug, brugge, AS. brycg, bricg; akin to Fries. bregge, D. brug, OHG. brucca, G. br[ u]cke, Icel. bryggja pier, bridge, Sw. brygga, Dan. brygge, and prob. Icel. br[=u] bridge, Sw. & Dan. bro bridge,… …   The Collaborative International Dictionary of English

  • suspension bridge — suspension bridges N COUNT A suspension bridge is a type of bridge that is supported from above by cables …   English dictionary

  • suspension bridge — ► NOUN ▪ a bridge in which the deck is suspended from cables running between towers …   English terms dictionary

  • suspension bridge — n. a bridge suspended from chains or cables which are anchored at either end and supported by towers at regular intervals …   English World dictionary

  • Suspension Bridge — (spr. Suspensch n Bridsch, d.i. Hängebrücke), Postort in der Grafschaft Niagara[110] des Staates New York (Nordamerika), am Niagara, eine Stunde unterhalb des Niagarafalls (s.d.), über welchen hier eine Hängebrücke mit Schienengeleisen zur… …   Pierer's Universal-Lexikon

  • suspension bridge — a bridge having a deck suspended from cables anchored at their extremities and usually raised on towers. [1815 25] * * * ▪ engineering  bridge with overhead cables supporting its roadway. One of the oldest of engineering forms, suspension bridges …   Universalium

  • suspension bridge — noun a bridge that has a roadway supported by cables that are anchored at both ends (Freq. 1) • Hypernyms: ↑bridge, ↑span • Instance Hyponyms: ↑Angostura Bridge, ↑Benjamin Franklin Bridge, ↑Bosporus Bridge, ↑ …   Useful english dictionary

  • suspension bridge — UK / US noun [countable] Word forms suspension bridge : singular suspension bridge plural suspension bridges a type of bridge that hangs from strong steel ropes that are fixed to towers …   English dictionary

  • suspension bridge — bridge that is suspended from steel cables …   English contemporary dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”