Fire pump

Fire pump

A fire pump is a part of a fire sprinkler system's water supply. The pump intake is either connected to the public underground water supply piping, or a static water source (e.g., tank, reservoir, lake). The pump provides water flow at a higher pressure to the sprinkler system risers and hose standpipes. A fire pump is tested and listed for its use specifically for fire service by a third-party testing and listing agency, such as UL or FM Global. The main code that governs fire pump installations in North America is the National Fire Protection Association's "NFPA 20 Standard for the Installation of Stationary Fire Pumps for Fire Protection".

Operation

Fire pumps may be powered either by an electric motor or a diesel engine, or, very occasionally a steam turbine. If the local building code requires power independent of the local electric power grid, a pump using an electric motor may utilize, when connected via a listed transfer switch, the installation of an emergency generator.

The fire pump starts when the pressure in the fire sprinkler system drops below a threshold. The sprinkler system pressure drops significantly when one or more fire sprinklers are exposed to heat above their design temperature, and opens, releasing water. Alternately, other fire hoses reels or other firefighting connections are opened, causing a pressure drop in the fire fighting main.

Fire pumps are needed when the local municipal water system cannot provide sufficient pressure to meet the hydraulic design requirements of the fire sprinkler system. This usually occurs if the building is very tall, such as in high-rise buildings, or in systems which require a relatively high terminal pressure at the fire sprinkler in order to flow a large volume of water, such as in storage warehouses. Fire pumps are also needed if fire protection water supply is provided from a ground level water storage tank.

Types of pumps used for fire service include: horizontal split case, vertical split case, vertical inline, vertical turbine, and end suction.

Jockey Pump

A jockey pump is a small pump connected to a fire sprinkler system and is intended to maintain pressure in a fire protection piping system to an artificially high level so that the operation of a single fire sprinkler will cause an appreciable pressure drop which will be easily sensed by the fire pump automatic controller, causing the fire pump to start. The jockey pump is essentially a portion of the fire pump's control system.

In the U.S.

The application of a jockey pump in a fire protection system is covered by documents produced by the NFPA (National Fire Protection Association, ) known as NFPA 20 "Fire Pumps" Standard and NFPA 13 "Design and Installation of Fire Sprinkler Systems". These must be inspected as with any other part of the system per NFPA 25 "Inspection and Testing of Water-Based Fire Protection Systems".Fire protection systems are governed in most states by statute, building code, and/or fire code.

In India

This jockey pump is also a must while designing the Fire Hydrants Pumps skid for Industrial installations.While the logic followed for the effective operation of the fire fighting pumps may depend upon or vary as per the regulations in a particular country, in India, the pump manufacturers like Mather-Platt with standard Fire Pumps generally adhere to the TAC guidelines (Tariff Advisory Committee guidelines).

Although India's premier manufacturer Kirloskar Brothers Limited, with approvals from UL and FM Global, LPCB, ASIB: follows TAC guidelines (Tariff Advisory Committee guidelines), or FM GLobal and UL standards depending on the clients needs.

If one is following the TAC guidelines, follow this approach

*Once the complete fire fighting circuit is under pressure by operating the pumps for sufficient time provided all the fire hydrant valves (Single yard hydrants, Fire escape hydrants, etc)are closed, the main pump stops.
*Due to some leakages somewhere in the fire fighting piping circuit, when there is a loss of system pressure which will be constantly monitored by the Pressure sensors in the circuit, the jockey pumps receives a signal to start from the automatic control panel, and will run to augment this loss of pressure by pumping more water into the circuit. Once the pressure is maintained as per the set point, it stops.
*If any hydrant valve is opened due to some fire and water is consumed, then the jockey pump due to its small capacity compared to the main pumps (one running, one stand-by)in terms of volumetric capacity, the main pump will start and then the jockey immediately stops.This way jockey pump is important which senses the loss of pressure in the circuit first.


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • fire pump — gaisrinis siurblys statusas Aprobuotas sritis gaisrinė sauga ir gelbėjimas apibrėžtis Siurblys skystoms gesinimo medžiagoms tiekti. atitikmenys: angl. fire pump šaltinis Priešgaisrinės apsaugos ir gelbėjimo departamento prie VRM direktoriaus… …   Lithuanian dictionary (lietuvių žodynas)

  • Fire apparatus — A fire apparatus, fire engine, fire truck, or fire appliance is a vehicle designed to assist in fighting fires, by transporting firefighters to the scene, and providing them with access, water or other equipment. In some areas, the terms fire… …   Wikipedia

  • Pump — For information on Wikipedia project related discussions, see . A pump is a device used to move gases, liquids or slurries. A pump moves liquids or gases from lower pressure to higher pressure, and overcomes this difference in pressure by adding… …   Wikipedia

  • Fire hydrant — in Charlottesville, Virginia, USA A fire hydrant (also known colloquially as a fire plug in the United States or as a johnny pump in New York City, because the firemen of the late 19th century were called Johnnies[ …   Wikipedia

  • Pump It Up NX2 — Developer(s) Nexcade Publisher(s) Andamiro …   Wikipedia

  • Fire and Rescue NSW — Motto:  Orta Recens Quam Pura Nites , (Newly Risen, How Brightly We Shine) Established 1884 …   Wikipedia

  • Pump It Up NX2 — Pump it Up Next Xenesis (o NX2 para abreviar) es el lanzamiento número 20 en los juegos de arcade de la serie Pump it up. fue lanzado mundialmente el 21 de enero del 2008 después de haber estado disponible en México y Corea del Sur un par de… …   Wikipedia Español

  • Pump It Up — Saltar a navegación, búsqueda Una máquina Pump it Up. Pump It Up es una serie de videojuegos arcade de simulación de baile lanzado por Andamiro en 1999. Consta de una máquina con una pantalla, parlantes y luces conectada a un tablero en el suelo …   Wikipedia Español

  • Pump It Up NX Absolute — Developer(s) Nexcade Publisher(s) Andamiro …   Wikipedia

  • Pump It Up — Разработчики Andamiro/F2/Freevolt/Nexcade Издатель …   Википедия

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”