Needle remover

Needle remover
a wall-mounted sharps container

Needle removers are devices that physically remove a needle from a syringe. In developing countries, there is still a need for improvements in needle safety in hospital settings as most of the needle removal processes are done manually and under severe risk of hazard from needles puncturing skin and allowing infection. These countries cannot afford needles with individual safety devices attached, so needle-removers must be used to remove the needle from the syringe. This lowers possible pathogen spread by preventing the reuse of the syringes, reducing incidents of accidental needle-sticks, and facilitating syringe disposal.

Contents

Background

In developing countries, most hospitals are lacking in needle safety. In regions surveyed by the World Health Organization (WHO), the reported number of needle-stick injuries in developing world countries ranged from .93 to 4.68 injuries per person and per year, which is five times higher than in industrialized nations (Department of Essential Health Technology, 2004). Needle-stick injuries are further complicated by disease transmission, such as Hepatitis B, Hepatitis C and HIV. In Ghana, a study of 803 schoolchildren revealed that 61.2% had at least one marker of hepatitis B virus (Sagoe-Moses et al., 2001). As a result, health care workers (HCWs), patients, and the community in developing nations are at an increased risk of contracting blood-borne pathogens via the reuse and improper disposal of needles, and accidental needle-sticks (Harner, 2004).

Before needle safety regulations, HCWs were on their own to avoid accidental needle-sticks and safely disposal of needles. However, in the U.S., after the Needlestick Safety Act signed in 2000 and the 2001 Bloodborne Pathogens Standard, the burden was no longer on HCWs. Both of these regulations mandated the use of safety devices and needle-removers with any sharps or needles (Jagger, 2003, 27-28). As a result, there was a large increase in research, development, and marketing of needle safety devices and needle-remover. In most hospital and medical settings in the U.S., needle safety regulations are maintained through individual needle safety devices and needle disposal boxes.

Existing solutions

One of the most common causes of needle-stick injuries, which the Needlestick Act and Bloodborne Pathogens Standard were attempting to decrease, was two-handed recapping (Wilburn, 2004). As a result, a one-handed capping mechanism was added to insulin and tuberculin syringes. The cap is attached to the syringe via a hinge, which allows the cap to be snapped onto the needle using one hand. The disadvantage to the hinge system is that the cap can get caught by jewelry and clothing, can get bumped when used, and the fixed position can be a hindrance during low angle injection. So Becton Dickinson (BD) has recently come out with a variation on this safety: instead of a hinge, the device slides over the needle and fully covers the tip of the needle, so accidental needle-sticks do not occur (Becton, Dickinson, and Company, 2004, BD SafetyGlide).

However, the rest of the world does not have similar needle and syringe regulations. For instance, the WHO is only able to regulate vaccinations in developing countries by ensuring that all vaccination syringes sent to these countries have autodisable features, since the major concern is the reuse of contaminated needles and syringes. These autodisable features allow the syringes to only be used once, so they cannot be reused. These mechanisms could be teeth that interlock to prevent the plunger from being pulled back for another use or a bag prefilled with the vaccine to stop reuse. For example, the SoloShot has a metal clip that locks the plunger down after one use (International Council of Nurses, 2005). The BD Uniject is a prefilled vaccine syringe that uses a plastic bulb instead of a plunger and has a disc valve to prevent reuse (Becton, Dickinson, and Company, 2005).

Still, over 90% of syringes worldwide do not have autodisable features (Harner, 2004). Individual protection devices are expensive, and regular needles are much more prevalent. Consequently, many developing world countries use needle-removers to reduce the risk of disease transmission via these exposed.

Benefits of needle-removers

Needle-removers minimize the occurrence of accidental needle-sticks because they allow immediate removal and containment of the needles, especially if the device is near the area of use. Reuse of syringes is prevented because the needle-remover physically separates the needle from the syringe, making the syringe useless. They also improve waste disposal by decreasing both the amount of infectious waste and the amount of safety boxes needed for the waste, since safety boxes can pack syringes 20-60% more compactly without the needles (Harner, 2004). Additionally, these devices are cost-efficient since one device can handle several hundred needles. Many developing world countries do not have the resources to afford auto-disable syringes, so with needle-removers, the hospitals can continue to use cheap syringes, while only paying a one-time fee to buy a needle-remover that has a life-span of about 200-500 needles (Harner, 2004).

Social and ethical implications

A significant ethical issue for the project is whether or not the needle-remover will cause more harm than its potential benefits. Engineers are obliged to use their skills and knowledge to improve the safety, health, and welfare of the public (Biomedical Engineering Society, 2004). The main concern is for the operator of the device; no engineer should create a device that could injure the operator. Another concern is that children may gain access to the device and accidentally hurt themselves. If a device design could potentially cause either of these problems, the team would be ethically obligated to reexamine that design, and it would either have to be improved or abandoned. When the device functions effectively and safely, it will serve to protect the welfare of the community. In developing countries, the risk of disease transmission is elevated due to the high percentage of needle-stick injuries, which is a result of inadequate needle collection devices (Department of Essential Health Technology, 2004). Increased pathogen transmission also occurs from the reuse of contaminated needles when supplies are low (Sagoe-Moses et al., 2001). The device will prevent reuse of needles and facilitate needle collection and disposal, and thus will improve the health and safety of hospital workers and the community.

The social and economic effects of the device also need to be recognized. In developing countries, the lack of proper needle collection devices leads to an increase in the number of occupational needle-sticks by HCWs via contaminated needles. Occupational needle-sticks account for 40%-65% of Hepatitis B and C infections in HCWs (Prüss-Üstün, Rapiti, and Hutin, 2003). As a result, more HCWs have to undergo postexposure testing and treatment, both of which cost money for the hospitals and the countries. There is also the manpower cost associated with losing trained HCWs to infections acquired on the job. With fewer than 10 doctors for every 100,000 individuals in sub-Saharan nations, any loss of hospital staff puts a strain of hospital resources. In addition, developing countries have made significant investments in training their HCWs, which is lost when occupational needle-sticks cause HCWs to leave the medical field (Sagoe-Moses et al., 2001).

The economic considerations are not just limited to costs associated with HCWs. Due to the high cost of needle-disposal containers and the fact that the containers usually have to be shipped overseas, unsafe and dangerous substitutes are used instead. This practice can potentially lead to needle-sticks by HCWs and individuals in the community, as well as needle reuse by members of the community, which can increase the potential spread of diseases.

Possible designs

The easiest needle-removers to operate are electrically powered, and either melt the needle or cut the needles at multiple sections. One patented design involves a syringe falling down into a chamber where powered moveable blades advance the syringe onto fixed blades on the opposite side, at which point the syringe is cut with a shearing motion at multiple points (Garvis and Beer, 1974). There are other patents that use electricity between electrodes or between rotating gears to short-circuit the needle and melt it off the syringe (Ch’ing-Lung, 1986; Hashimoto, 1990). A more complex design involves a hammer mill and grinder to break up and grind up the plastic and metal parts of the syringes, after which, the pieces are heated and cooled. The end result is metal particles encapsulated in a piece of plastic (Wallace et al., 1991).

However, electricity in developing countries is not a dependable source, so hand-powered needle-cutters would be preferred. Some designs use the squeezing force from a hand to force one or two blades to shear across each other and hence cut the needle between the blades (Choksi et al., 1981; Harner, 2004). There are other designs in which a twisting motion brings a shearing blade in contact with the needle and thus cuts it (W. Thead, D. Thead, and Evans, 2000). Another design has a stationary outer surface that the syringe body rests against and a cylindrical inner cutting body with a bore for the needle to pass through. A lever rotates the inner body, which shears the needle from the syringe and dumps the needle into a container (Johan and Morner, 1972). A crank system can be used to power a similar design, which also uses a cylindrical inner body. However instead of cutting the needle, the device pulls the needle completely out of the syringe, which deforms the needle, and dumps it into a container (Samuel, 2004). A more complicated design actually pulls the needle and collar from the barrel of the syringe without a rotational motion: the downward motion of putting the syringe into the device powers two arms to pull the needle off the syringe. The interesting aspect of this device is that it appears to be one-handed (Atsumi, 1996). Another one-handed device uses a downward motion to cause rotating gears to unscrew the needle and collar from the syringe (Thead and Evans, 1991). This design is very complex to implement, so an improvement of this design involves pegs that grip and rotate the needle collar instead of gears. The downward force is transferred into moving the pegs in helical slots, which causes the collar to rotate and the needle to be removed from the syringe (Han, 1994).

In 2006 a cheap and simple solution utilizing old cola or beer cans to dispose needles and specially developed lid to safely seal them has been developed. One click and the can is permanently sealed by the safely seal. The snap-lock seals the two parts together without using glue or tools. The ’collar’ of the cap is protecting the user during the needle separation process. The insertion hole is designed to separate needle and syringe at the point of use. No finger can pass through the opening. Each can securely contains 150-200 used needles (Business Ideas Forum, 2007).

Commercial models

There are several electrically powered needle-removers on the market now. The Disintegrator Needle Destruction Device, offered by American Scientific Resources (ASFX), uses plasma arch technology to destroy the needle, kill pathogens and blunt the syringe. Designed to be used with only one hand, this device completely eliminates the sharp. One model from Techno Fab uses a regular electrical short-circuit to melt the needle, while another needle-remover, seen at CarePathways.com, uses a plasma arc to melt the needle. A unique needle-remover design is the Needle Remover Device, designed by the Program for Appropriate Technology in Health (PATH). It uses two handles that are squeezed together to slide two circular blades across each other, which cuts the hub from the syringe. It is also reusable, and its target cost is about $15 (Harner, 2004). Another needle-removers currently on the market is Advanced Care Products’s Clip&Stor, which uses a hand-powered clipper action to remove the needle (Advanced Care Products, 2005). The cost of the Clip&Stor is about seven dollars. There is also the BD Hub Cutter, which uses a squeezing hand motion to cut the syringe. The edges of the squeezable parts have blades that do the actual cutting. However, unlike a regular needle-remover, the BD Hub Cutter cuts the syringe at the hub so the needle is completely separated from the syringe. As a result, the risk of a contaminated puncture is completely eliminated because no needle shards remain on the syringe. The Hub Cutter is not reusable though, and disposal of the whole unit must occur (Becton, Dickinson, and Company, 2004). The cost of the Hub Cutter is about four dollars (Department of Essential Health Technology, 2004).

Limitations

Most of these current needle-removers require the use of two hands; one to hold the needle in place and the other to activate the mechanism. This form of operation can cause problems because if hospital personnel are busy, especially in a developing world country, they may not have the time or hands needed to operate the device. As a result, the needle will remain exposed on the syringe, posing a risk to both HCWs and patients.

Furthermore, many of these existing needle-removers do not make use of cheap and readily available materials, like used motor oil jugs, for containers, which raises the price of the device and requires that the hospital continuously buys more containers from the company. A typical 3-gallon Bemis sharps container with a rotating lid costs about $8 without including shipping costs (GRP & Associates, 2005). If these containers must be shipped overseas, the price of the device can far exceed the available resources of many hospitals in developing countries, which causes them not to buy needle-removers.

See also

References

  1. Advanced Care Products, Ltd. (2005). Clip&Stor – Pen Needle and Syringe Needle Cutter. Retrieved October 5, 2005. <http://www.advancedcareproducts.co.uk/>
  2. Atsumi, H. (1996, December 31). Patent #5588966: Device for Removing a needle from a Syringe. Retrieved October 24, 2005. <http://www.freepatentsonline.com/5588966.pdf>
  3. Becton, Dickinson, and Company. (2004). BD Hub Cutter. Retrieved October 23, 2005. <http://www.bd.com/immunization/pdfs/products/bd_hub_cutter_brochure.pdf>
  4. Becton, Dickinson, and Company. (2004). BD SafetyGlide Syringe for Insulin, TB, and Allergy: Quick Reference Card. Retrieved October 23, 2005. <http://www.bd.com/safety/pdfs/BD_safetyglide_syringe_usage.pdf>
  5. Becton, Dickinson, and Company. (2005). BD Uniject: Prefill Injection Device. Retrieved October 23, 2005. < http://www.bd.com/immunization/pdfs/products/bd_uniject.pdf>
  6. Biomedical Engineering Society. (2004). Code of Ethics. <http://www.bmes.org/pdf/2004ApprovedCodeofEthicsShortForm.pdf>
  7. Business Ideas Forum. (2006). Antivirus – a cap to protect against needle infections. <http://www.business-idea.com/ShowPosting.asp?ID=2327>
  8. CarePathways.com. (2005). Disintegrator plus Insulin Needle Destruction. Retrieved October 25, 2005. <http://www.carepathways.com/estore.cfm?ID=SFG1986069-EA>
  9. Ch’ing-Lung, H. (1986, December 9). Patent #4628169: Mini Electrical Syringe Needle Destroyer. Retrieved October 17, 2005. <http://www.freepatentsonline.com/4628169.pdf>
  10. Choksi, P. et al. (1981, March 17). Patent #4255996: Needle Destroyer with Improved Mechanical Advantage. Retrieved October 18, 2005. <http://www.freepatentsonline.com/4255996.pdf>
  11. Department of Essential Health Technology. (2004). Proposed Agenda to Evaluate the Risks and Benefits Associated with Using Needle-Removing Devices. Retrieved October 22, 2005. <http://www.who.int/injection_safety/toolbox/docs/en/AgendaNeedleRemoval.pdf>
  12. Garvis, M. and Beer, M. (1974, April 2). Patent #3800644: Destruction and Disposal Device for Hypodermic Syringes and the Like. Retrieved October 17, 2005. <http://www.freepatentsonline.com/3800644.pdf>
  13. GRP & Associates, Inc. (2005). Medical Waste Disposal Supplies. Retrieved 12-7-05. <http://www.sharpssupply.com/mcart/>
  14. Han, S. (1994, May 17). Patent #5312346: Needle Removing Device. Retrieved October 13, 2005. <http://www.freepatentsonline.com/5312346.pdf>
  15. Harner, C. (2004, October). Needle Remover Device Design Transfer Package. Retrieved September 7, 2005. <http://www.healthcarewaste.org/documents/PATH_needleRemover_design.pdf>
  16. Hashimoto, T. (1990, October 9). Patent #4961541: Apparatus for Disposing of a Used Hypodermic Syringe. Retrieved October 17, 2005. <http://www.freepatentsonline.com/4961541.pdf>
  17. International Council of Nurses. (2005). Nursing Matters fact sheet. “First Do No Harm: Auto-Disable Syringes for Immunization Safety”. Retrieved October 22, 2005. < http://www.icn.ch/matters_syringes_print.htm>
  18. Jagger, J., De Carli, G., Perry, J., Puro, V., Ippolito, G. (2003). Chapter 31: Occupational Exposure to Bloodborne Pathogens: Epidemiology and Prevention. Prevention and Control of Nosocomial Infections (4th Ed). Lippincott, Williams, and Wilkins.
  19. Johan, B. and Morner, S. (1972, August 15). Patent #3683733: Apparatus for Destroying Hypodermic Needles, Needle-Equipped Ampules, Hypodermic Syringes, and the Like. Retrieved October 13, 2005. <http://www.freepatentsonline.com/3683733.pdf>
  20. Prüss-Üstün A., Rapiti E., Hutin Y. (2003). Sharps injuries: global burden of disease from sharps injuries to health-care workers. Geneva, World Health Organization (WHO Environmental Burden of Disease Series, No. 3).
  21. Samuel, P. R. (2004, September 21). Patent #6792662: Needle Puller for Destroying Hypodermic Needles. Retrieved October 25, 2005. <http://www.freepatentsonline.com/3683733.pdf>
  22. Techno Fab. (2005). Needle Destroyer. Retrieved October 22, 2005. <http://www.technofab.net/needes.htm>
  23. Thead, W. and Evans, J. (1991, January 22). Patent #4986811: Apparatus and Method for Safely Removing Needles from Syringes. Retrieved October 13, 2005. <http://www.freepatentsonline.com/4986811.pdf>
  24. Thead, W., Thead, D., and Evans, J. (2000, December 12). Patent #6158314: Method and Apparatus for Disabling and Disposing of a Single-Use Hypodermic Syringe. Retrieved October 23, 2005. <http://www.freepatentsonline.com/6158314.pdf>
  25. Sagoe-Moses, C., et al. (2001, August 16). Sounding Board: Risks to Health Care Workers in Developing Countries. N Eng J Med 345 (7): 538-541.
  26. Wallace, A. et al. (1991, September 10). Patent #5046669: Syringe Disposal Apparatus and Method. <http://www.freepatentsonline.com/5046669.pdf>
  27. Wilburn, S. (2004). Preventing Needlestick Injuries among Health Care Workers: A WHO-ICN Collaboration. Int J Occup Environ Health 10:451-456.

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Hypodermic needle — A hypodermic needle is a hollow needle commonly used with a syringe to inject substances into the body. They may also be used to take liquid samples from the body, for example taking blood from a vein in venipuncture.A hypodermic needle is used… …   Wikipedia

  • Sharps waste — is a form of medical waste composed of used sharps , which includes any device or object used to puncture or lacerate the skin. Sharps waste is classified as biohazardous waste and must be carefully handled. Common medical materials treated as… …   Wikipedia

  • Remove — or remover may refer to:* Removalist or household goods Mover * Hare Remover , 1945 Merrie Melodies cartoon * Needle remover * Pet eye remover, in photographic retouching * Polish remover * Staple removerSee also* Delete * Relocate * Removable… …   Wikipedia

  • Injection (medicine) — This article is about the medical procedure. For other uses, see Injection. A Somali boy receiving a subcutaneous injection of polio vaccine An injection (often referred to as a shot or a jab ) is an infusion method of putting fluid into the body …   Wikipedia

  • Sharps container — A sharps container is a container that is filled with used medical needles (and other sharp medical instruments, such as an IV catheter). They fit into two main types: * single use which are disposed of with the waste inside, * reusable which are …   Wikipedia

  • Ngoy Mushola — is a DR Congolese medical doctor. Mushola, who is from Bumba, was the first person to record a description of the Ebola virus. It occurred Yambuku, DR Congo.[1] See also VHFs Blood borne pathogens (BBP) Universal precautions Needle remover Sharps …   Wikipedia

  • Yambuku — is a small village in the Democratic Republic of the Congo (previously Zaire) and was the site of the first known outbreak of the Ebola Zaire strain of the Ebola hemorrhagic fever virus in 1976. It is also the place where flying tree squirrels… …   Wikipedia

  • Matthew Lukwiya — Born 24 November 1957 Kitgum …   Wikipedia

  • Mweka, Democratic Republic of the Congo — This article is about the DR Congolese town. For the Mt Kilimanjaro locality, see College of African Wildlife Management . Mweka is a town in southern central Democratic Republic of the Congo, situated on the Kasai railway line between Kananga… …   Wikipedia

  • Needlegun scaler — A U.S. Navy Seaman uses a needle gun to remove old paint and corrosion aboard USS Kitty Hawk.[1] A needlegun scaler or needle gun is a tool used in metalwork applications as diverse as home repair, automotive repair and shipboard preservation …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”