Computer to plate

Computer to plate

Computer to plate (CTP) is an imaging technology used in modern printing processes. In this technology, an image created in a Desktop Publishing (DTP) application is output directly to a printing plate.

Negative lithographic printing plate
Agfa Advantage DL violet laser fotosetter with VPP68 plate processor

This compares with the older technology, Computer to film (CTF), where the computer file is output onto a photographic film. This film is then used to make a printing plate, in a similar manner to a contact proof in darkroom photography.

Contents

Technology

CTP methods differ according to the construction type of the imagesetter and the light source used to expose the plate surface. In terms of construction type there are three different kinds: internal drum, external drum and flat-bed imagesetters. The two main light sources used to expose the plate are ultraviolet light lamps and laser diodes. The wavelength and energy of the laser diodes depend on the type of plate that is used. This technology is mainly use in newspaper and magazine printing.[1]

Internal drum imagesetters

In an internal drum imagesetter the plate is put into a cylinder, while the imaging head moves along the axis of the cylinder to expose the plate. The rotating mirror at the end of the imaging head rotates around its axis to beam the laser on the desired part of the fixed plate. The construction type makes it more difficult to use several lasers at the same time, but just using one laser also has advantages like uniform beam intensity over the whole plate. [1]

External drum imagesetters

The plate is wrapped around a drum that can rotate around its axis, while the imaging head that projects the image on the plate can move along this axis to focus the laser beam on the surface. The simple construction type makes it possible to arrange multiple image heads next to each other and use them simultaneously. This leads to a decrease of the imaging time needed to expose a whole printing plate. [1]

Flat-bed imagesetters

The image is reproduced line by line on a fixed flat printing plate by a laser beam that is deflected by a rotating polygon mirror and then onto the printing plate. Because of the setup the laser beam be-comes less accurate at the edges of the printing plate and is therefore mainly smaller formats or production with lower quality expectations. [1]

Types of CTP-Plates (Computer-to-plate)

Photopolymer plates

  • photosensitivity between 400 to 550 nm
  • low laser energy of 100 to 200 µJ/cm2 needed for exposure
  • run lengths of up to 200.000 prints

Silverhalogen plates

  • silverhalogen aluminium printing plates
  • photosensitivity between 400 to 700 nm
  • low laser energy of 1 to 2 µJ/cm2 needed for exposure
  • run lengths of up to 150.000 prints
  • resolution to 250 LPI possible
  • dot reproduction 1–99 %

Thermal plates

  • photosensitivity between 830 to 1.070 nm
  • high laser energy of up to 500 µJ/cm2 needed for exposure
  • run lengths of up to 100.000 prints
  • resolution to 200 LPI possible
  • dot reproduction 1–99%
  • high process stability
  • many providers
  • processing in the daylight possible

Advantages of CTP vs. CTF

CTP has several advantages over conventional platemaking. In CTP, one generation (transfer of film image to the printing plate) is removed from the printing process (eliminating the need for film and related developer chemicals), increasing sharpness and detail. CTP avoids potential losses in quality that may occur during film processing, including scratches in the film, and variations in the exposure. An imagesetter usually has an accuracy rate of +/-2%.[2] Plates are produced in less time, are more consistent, and at a lower cost. CTP can also improve registration and image-to-edge repeatability over traditional methods.

In CTP, the media is registered (held in precise position) in the platesetter during imaging, and does not rely on a separately-aligned pin grid, as is the case with film. Defects due to dust, scratches or other artifacts are minimized.

CTP systems can significantly increase plate production outputs. Platesetters for newspaper production can output up to 300 12-inch (300 mm) plates per hour at 1270 DPI (dots per inch), whilst for commercial applications a CTP system could output 60 B1 plates at 2400 DPI for higher screen rulings.

Small portrait presses that typically create 1 or 2 color output can use anything from a standard laser printer, for low quality/low volume, up to a higher-end dedicated platesetter for higher quality and volume.

Disadvantages of CTP vs. CTF

• Restricted to digital format. CTP productions require that the basis for the printed matter as well as the imposition, be digital.

• Remaking of plates. If for some reason a CTP plate is damaged, if an error occurs when it's ripped or if something has to be corrected after the plate is exposed, a completely new, imposed plate must be created.[2]

References

  1. ^ a b c d Kipphan, Helmut. Handbook of print media: technologies and production methods. Springer; 2011. ISBN 9783540673262. p. 597-603.
  2. ^ a b Johansson, Kaj (2003). A Guide to Graphic Print Production. Wiley. ISBN 0-4712-7347-3. 

See also

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Computer To Plate — Le computer to plate plus communément appelé CtP (littéralement « ordinateur vers plaque ») est un périphérique informatique d écriture destiné à l imprimerie, permettant de créer directement les plaques destinées aux presses à partir d …   Wikipédia en Français

  • Computer to Plate — Le computer to plate plus communément appelé CtP (littéralement « ordinateur vers plaque ») est un périphérique informatique d écriture destiné à l imprimerie, permettant de créer directement les plaques destinées aux presses à partir d …   Wikipédia en Français

  • Computer to Plate — Eine ablative negative Offset Druckplatte beim Nachmessen nach dem Druck (Magenta). Dieser Typ braucht keine Entwicklung mehr, sondern nur eine Absaugung im CTP Belichter Der Begriff Computer to Plate (CTP) oder deutsch Digitale… …   Deutsch Wikipedia

  • Computer to plate — Eine ablative negative Offset Druckplatte beim Nachmessen nach dem Druck (Magenta). Dieser Typ braucht keine Entwicklung mehr, sondern nur eine Absaugung im CTP Belichter Der Begriff Digitale Druckplattenbelichtung (DDB) oder englisch Computer to …   Deutsch Wikipedia

  • Computer to plate — Le computer to plate plus communément appelé CtP (littéralement « ordinateur vers plaque ») est un périphérique informatique d écriture destiné à l imprimerie, permettant de créer directement les plaques destinées aux presses à partir d …   Wikipédia en Français

  • Computer to Plate — placa offset negativa Computer to Plate o simplemente CtP es una tecnología de artes gráficas por medio de la cual las placas de impresión Offset o flexográfica son copiadas por máquinas manipuladas directamente de un computador, mejorando… …   Wikipedia Español

  • Computer-to-Plate-Verfahren — Com|pu|ter to Plate Ver|fah|ren [...tu pleit...] das; s <zu engl. to plate »auf die (Druck)platte«> Druckverfahren, bei dem die Druckplatten direkt (ohne den bisherigen Umweg über die Filmbelichtung) vom Computer aus beschrieben werden (EDV …   Das große Fremdwörterbuch

  • Computer to Plate — …   Википедия

  • Computer To Film — Le computer to film (CTF, littéralement ordinateur vers film) ou flashage est un procédé d impression dans lequel un périphérique informatique insole des films destinés ensuite à la fabrication des plaques pour les presses offset à partir d un… …   Wikipédia en Français

  • Computer to Film — Le computer to film (CTF, littéralement ordinateur vers film) ou flashage est un procédé d impression dans lequel un périphérique informatique insole des films destinés ensuite à la fabrication des plaques pour les presses offset à partir d un… …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”