Fiberglass molding

Fiberglass molding

Fiberglass molding is a process in which fiberglass reinforced resin plastics are formed into useful shapes.

Mold Making

The fiberglass mold process begins with an object known as the plug or buck. This is an exact representation of the object to be made, and can be made from a variety of different materials. Certain types of foam are commonly used.

After the plug has been formed, it is sprayed with a mold release agent. The release agent will allow the mold to be separated from the plug once it is finished. The mold release agent is a special wax, and/or PVA (Polyvinyl alcohol). Polyvinyl Alcohol, however, is said to have negative effects on the final mold's surface finish.

Once the plug has its release agent applied, gelcoat is applied with a roller, brush or specially-designed spray gun. The gelcoat is pigmented resin, and gives the mold surface a harder, more durable finish.

Once the release agent and gelcoat are applied, layers of fiberglass and resin are laid-up onto the surface. The fiberglass used will typically be identical to that which will be used in the final product.

In the laying-up process, a layer of fiberglass mat is applied, and resin is applied over it. A special roller is then used to remove air bubbles. If left in the curing resin, air bubbles would significantly reduce the strengh of the finished mold.

Once the final layers of fiberglass are applied to the mould, the resin is allowed to set-up and cure. Wedges are then driven between the plug and the mold in order to separate the two.

Advanced techniques such as Resin Transfer Molding are also used.

Making a Component

The component-making process involves building up a component on the fiberglass mold. The mold is a "negative" image of the component to be made, so the fiberglass will be applied inside the mold, rather than around it.

As in the mold-making process, release agent is first applied to the mold. Colored gelcoat is then applied. Layers of fiberglass are then applied, using the same procedure as before. Once completed and cured, the component is separated from the mold using wedges, compressed air or both.

ee also

* Fibre-reinforced plastic
* Glass-reinforced plastic


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Fiberglass spray lay-up process — is similar to the hand lay up process. The difference comes from the application of the fiber and resin material to the mold. Spray up is an open molding composites fabrication process where resin and reinforcements are sprayed onto a reusable… …   Wikipedia

  • Fiberglass — This article is about the plastic composite. For insulation material, see glass wool. For the fiber itself, see glass fiber. Fiberglass (also called glass reinforced plastic, GRP[1], glass fiber reinforced plastic, or GFRP[2]), is a fiber… …   Wikipedia

  • Compression molding — Compression molded rubber boots before the flashes are removed. Compression molding is a method of molding in which the molding material, generally preheated, is first placed in an open, heated mold cavity. The mold is closed with a top force or… …   Wikipedia

  • Glass-reinforced plastic — (GRP), is a composite material or fiber reinforced plastic made of a plastic reinforced by fine fibers made of glass. Like graphite reinforced plastic, the composite material is commonly referred to by the name of its reinforcing fibers… …   Wikipedia

  • Plastics engineering — encompasses the processing, design, development, and manufacture of plastics products. A plastic is a polymeric material that is in a semi liquid state, having the property of plasticity and exhibiting flow. The nature of plastic materials poses… …   Wikipedia

  • Laine De Verre — La laine de verre est un matériau se présentant comme un matelas de fibres de verre extrêmement fines[1]. On l utilise dans le bâtiment comme isolant thermique, isolant acoustique ou absorbant acoustique, ou pour la protection contre l’incendie.… …   Wikipédia en Français

  • Boat building — Boat building, one of the oldest branches of engineering, is concerned with constructing the hulls of boats and, for sailboats, the masts, spars and rigging.Parts* Bow the front and generally sharp end of the hull. It is designed to reduce the… …   Wikipedia

  • Boat — A boat is a watercraft of modest size designed to float or plane on water, and provide transport over it. Usually this water will be inland (lakes) or in protected coastal areas. However, boats such as the whaleboat were designed to be operated… …   Wikipedia

  • Carbon-fiber-reinforced polymer — For fibers of carbon, see carbon (fiber). Tail of an RC helicopter, made of CFRP Carbon fiber reinforced polymer or carbon fiber reinforced plastic (CFRP or CRP or often simply carbon fiber), is a very strong and light fiber reinforced polymer… …   Wikipedia

  • Window screen — A window screen, insect screen or bug screen is a metal wire, fiberglass, or other synthetic fiber mesh, stretched in a frame of wood or metal, designed to cover the opening of an open window. Its primary purpose is to keep leaves, debris,… …   Wikipedia

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”