Steam locomotive

Steam locomotive

A steam locomotive is a locomotive powered by steam. The term usually refers to its use on railways, but can also refer to a "road locomotive" such as a traction engine or steamroller.

Steam locomotives dominated rail traction from the mid 19th century until the mid 20th century, after which they were superseded by diesel and electric locomotives.

Origins

"See also: History of rail transport, "

The earliest railways employed horses to draw carts along railed tracks.

As the development of steam engines progressed through the 1700s, various attempts were made to apply them to road and railway use.cite book
last=Payton |first=Philip|year=2004 |title=Oxford Dictionary of National Biography
publisher=Oxford University Press
] The first attempts were made in Great Britain; the earliest steam rail locomotive was built in 1804 by Richard Trevithick and Andrew Vivian. It ran with mixed success on the narrow gauge "Penydarren tramroad" at Merthyr Tydfil in Wales.. Then followed the successful twin cylinder locomotive by Christopher Blackett's team built at Wylam in 1811, closely followed by Matthew Murrays' rack locomotive for the edge railed Middleton Railway in 1812 cite book
last=Young |first=Robert
title=Timothy Hackworth and the Locomotive
publisher=the Book Guild Ltd
location=Lewes, UK
date=2000
edition(=reprint of 1923 ed.)
] . These early efforts culminated in 1829 with the Rainhill Trials and the opening of the Liverpool and Manchester Railway a year later making exclusive use of steam power for both passenger and freight trains.

The United States started developing steam locomotives in 1829 with the Baltimore and Ohio Railroad's "Tom Thumb". This was the first locomotive to run in America, although it was intended as a demonstration of the potential of steam traction, rather than as a revenue-earning locomotive. The first successful steam railway in the US was the South Carolina Railroad whose inaugural train ran in December 1830 hauled by the "Best Friend of Charleston". Many of the earliest locomotives for American railroads were imported from England, including the "Stourbridge Lion" and the "John Bull", but a domestic locomotive manufacturing industry was quickly established, with locomotives like the "DeWitt Clinton" being built in the 1830s.cite book
title=The Pictorial Encyclopedia of Railways
author=Hamilton Ellis
publisher=The Hamlyn Publishing Group
year=1968 |pages=pp.24-30
]

Basic form

Boiler

The typical steam locomotive employs a horizontal fire-tube boiler partially filled with water. A firebox, its walls and roof constantly surrounded by water, is incorporated generally to the rear of the boiler when the locomotive is traveling chimney-first. This is where a combustible is burnt, the heat generated thereby being transferred to the water in the boiler in order to make the steam that constitutes working medium. The combustion gases flow from the firebox into a bundle of parallel tubes, also surrounded by water, which continue to transfer heat to the water. At the front of the boiler is the smokebox, a chamber where the combustion gases are mixed with the jet of exhaust steam, the whole being ejected into a chimney (US: "smoke stack") voiding into the outside air.

team circuit Anchor|Steam circuit

The generated steam is stored in the steam space above the water in the partially-filled boiler. Its working pressure is limited by spring-loaded safety valves. It is then collected either in a perforated tube fitted above the water level or from a dome that often houses the regulator valve, or throttle, the purpose of which is to control the amount of steam leaving the boiler. The steam then either travels directly along and down a steam pipe to the engine unit or may have first to pass into the wet header of a superheater, the role of the latter being to eliminate water droplets suspended in the "saturated steam", the state in which it leaves the boiler. On leaving the superheater, the "dried" steam exits the dry header of the superheater and passing down a steam pipe enters the steam chests adjacent to the cylinders of a reciprocating engine. Inside each steam chest is a sliding valve that distributes the steam via ports that connect the steam chest to the ends of the cylinder space. The role of the valves is twofold: admission of each fresh dose of steam and exhaust of the used steam once it has done its work.

The cylinders are double acting, with steam admitted to each side of the piston in turn. In a two-cylinder locomotive, one cylinder is located on each side of the locomotive. The cranks are set 90° out of phase with each other. During a full rotation of the driving wheel, steam provides four power strokes per revolution; that is to say each cylinder receives two injections of steam. The first stroke is to the front of the piston and the second stroke to the rear of the piston; hence two working strokes. Consequently two deliveries of steam onto each piston face in two cylinders generates a full revolution of the driving wheel. Each piston is connected to the driving axle on each side by a connecting rod, the driving wheels are connected together by coupling rods to transmit power from the main driver to the other wheels. At the two "dead centres", when the connecting rod is on the same axis as the crankpin on the driving wheel, it will be noted that no turning force can be applied. If the locomotive were to come to rest in this position it would be impossible for it to move off again, so the cylinders and crankpins are arranged such that the dead centres occur out of phase with each other. This precaution is unnecessary on most other reciprocating engines (such as an internal combustion engine) which are never expected to start from rest under their own power, and employ a flywheel to overcome the dead centres.

Each piston transmits power directly through a connecting rod (US: main rod) and a crankpin (US: wristpin) on the driving wheel (US main driver) or to a crank on a driving axle. The movement of the valves in the steam chest is controlled through a set of rods and linkages called the valve gear, actuated from the driving axle or else from the crankpin; the valve gear includes devices that combine the roles of reversing the engine, adjusting valve travel and the timing of the admission and exhaust events. The cut-off point determines the moment when the valve blocks a steam port, "cutting off" admission steam and thus determining the proportion of the stroke, during which steam is admitted into the cylinder; for example a 50% cut-off admits steam for half the stroke of the piston. The remainder of the stroke is driven by the expansive force of the steam. Careful use of cut-off provides economical use of steam and, in turn, reduces fuel and water consumption. The reversing lever (US: Johnson bar), or screw-reverser, (if so equipped) which controls the cut-off therefore performs a similar function to a gearshift in an automobile- 100% cut-off , providing maximum tractive effort at the expense of efficency, is used to pull away from a standing start, whilst a cut-off as low as 10% is used when cruising, providing reduced tractive effort but with lower fuel/water consumption. cite book
last=Ahrons
title=The British Steam Railway Locomotive from 1825 to 1925
volume=vol. 1
]

[
Walschaerts valve gear in a steam locomotive. In this animation, the red colour represents live steam entering the cylinder, blue represents expanded (spent) steam being exhausted from the cylinder. Note that the cylinder receives two steam injections during each full rotation; the same occurs in the cylinder on the other side of the engine.] clr

Exhaust steam is directed upwards to the atmosphere through the chimney, by way of a nozzle called a blastpipe that gives rise to the familiar "chuffing" sound of the steam locomotive. The blastpipe is placed at a strategic point inside the smokebox that is at the same time traversed by the combustion gases drawn through the boiler and grate by the action of the blast. The combining of the two streams is crucial to the efficiency of any steam locomotive and the internal profiles of the chimney, (or more strictly speaking, the "ejector") require careful design and adjustment. This has been the object of intensive studies by a number engineers (and almost totally ignored by others with sometimes catastrophic effect). The fact that the draught depends on the exhaust pressure means that power delivery and power generation are automatically self-adjusting and among other issues, a balance has to be struck between obtaining sufficient draught for combustion whilst giving the gases and particles sufficient time to be consumed. In the past, fierce draught could lift the fire off the grate, or cause the ejecting of unburnt particles leading to the dirt and pollution for which steam locomotives had an unenviable reputation in the past. Moreover, the pumping action of the exhaust has the counter effect of exerting "back pressure" on the side of the piston receiving steam, thus somewhat reducing cylinder power. Designing the exhaust ejector has become a specific science in which Chapelon, Giesl [ [http://de.wikipedia.org/wiki/Adolph_Giesl-Gieslingen] ] and Porta were successive masters, and was largely responsible for spectacular improvements in thermal efficiency but drastic reduction in maintenance time See section of the LNER Class A1/A3 article on the sharp increase in availability brought about in this respect by the application of the Kylchap exhaust to Gresley Pacifics in the early 1960s] and pollution. A similar system was used by some early gasoline/kerosene tractor manufacturers (Advance-Rumely/Hart-Parr) – the exhaust gas volume vented through a cooling tower meant that more exhaust drew more air past the radiator.

Chassis

With European locomotives, the chassis is the principal structure onto which the boiler is mounted and which incorporates the various elements of the running gear.The chassis consists of two mainframes kept apart and square by spacers and "buffer beams". For many years, in American practice, the boiler was the main structural element, with built-up bar frames, "smokebox saddle/cylinder" structure and drag beam integrated therein; but from the late 1920s with the introduction of "superpower", the "cast-steel locomotive bed" became the norm, incorporating frames, spring hangers, motion brackets, smokebox saddle and cylinder blocks incorporated into a single complex, sturdy but heavy casting. André Chapelon developed a similar structure but of welded construction with around 30% saving in weight for the still-born 2-10-4 locomotives the construction of which was begun then abandoned in 1946.

Running gear

This includes the brake gear, wheel sets, axleboxes, springing and the "motion" that includes connecting rods and valve gear. The transmission of the power from the pistons to the rails and the behaviour of the locomotive as a vehicle, able to negotiate curves, points and irregularities in the track is of paramount importance. Because reciprocating power has to be directly applied to the rail from 0 rpm upwards, this poses unique problems of "adhesion" of the driving wheels to the smooth rail surface. Adhesive weight is the portion of the locomotive's weight bearing on the driving wheels. This is made more effective if a pair of driving wheels is able to make the most of its "axle load" i.e. its individual share of the adhesive weight. Locomotives with "compensating levers" connecting the ends of plate springs have often been deemed a complication but locomotives fitted with them have usually been less prone to loss of traction due to wheel-slip.

Locomotives with total adhesion, i.e. where all the wheels are coupled together, generally lack stability at speed. This makes desirable the inclusion of unpowered carrying wheels mounted on two-wheeled trucks or 4-wheeled bogies centred by springs that help to guide the locomotive through curves. These usually take the weight of the cylinders in front or of the firebox at the rear end when the width of this exceeds that of the mainframes. For multiple coupled wheels on a rigid chassis a variety of systems for controlled side-play exist.

Fuel and water

.

The fuel source used depends on what is economically available locally to the railway. In the UK and parts of Europe, a plentiful supply of coal made this the obvious choice from the earliest days of the steam engine. German, Russian, Australian and British railways experimented using coal dust to fire locomotives. Up to around 1850 in the U.S.A the vast majority of locomotives burnt wood until most of the Eastern forests were cleared; from that time on coal burning became more widespread and wood burners were restricted to rural and logging districts. In Europe, this lasted well into the 20th century. Bagasse, a waste by-product of the refining process, was burned in sugar cane farming operations. In the USA, the ready availability of oil made this a popular steam locomotive fuel; the Southern Pacific, for example, went directly from wood to oil.Fact|date=February 2007 equipment. In Victoria, Australia after World War II, many steam locomotives were converted to heavy oil firing.

A number of tourist lines and heritage locomotives in Switzerland, Argentina and Australia have been using light diesel-type oil.cite newsgroup
url=http://groups.google.com/group/aus.rail/browse_thread/thread/c40d030b1d87edbe/a386d68a957350b9?#a386d68a957350b9
newsgroup=aus.rail
title=West Coast and R711
] .

Water was supplied at stopping places and locomotive depots from a dedicated water tower connected to water cranes or gantries. In the UK, the USA and France, water troughs (US track pans) were provided on some main lines to allow locomotives to replenish their water supply without stopping. This was achieved by using a 'water scoop' fitted under the tender or the rear water tank in the case of a large tank engine; the fireman remotely lowered the scoop into the trough, the speed of the engine forced the water up into the tank, and the scoop was raised again once it was full.

Water is an essential element in the operation of a steam locomotive; because as Swengel argued:

it has the highest specific heat of any common substance; that is more thermal energy is stored by heating water to a given temperature than would be stored by heating an equal mass of steel or copper to the same temperature. In addition, the property of vapourising (forming steam) stores additional energy without increasing the temperature...water is a very satisfactory medium for converting thermal energy of fuel into mechanical energy

Swengel went on to note that "at low temperature and relatively low boiler outputs" good water and regular boiler washout was an acceptable practise, even though such maintenance was high. As steam pressures increased, however, a problem of "foaming" or "priming" developed in the boiler, wherein dissolved solids in the water formed "tough-skinned bubbles" inside the boiler, which in turn were carried into the steam pipes and could blow off the cylinder heads. To overcome the problem, hot mineral concentrated water was deliberately wasted (blowing down) from the boiler from time to time. Higher steam pressures required more blowing down of water out of the boiler. Oxygen generated by boiling water attacks the boiler and with increased steam pressures the rate of rust (iron oxide) generated inside the boiler increases. One way to help overcome the problem was water treatment. Swengel suggested that the problems around water, contributed to the interest in electrification of railways. Swengel p. 146]

In the 1970s L.D. Porta developed a sophisticated heavy duty chemical water treatment that not only keeps the inside of the boiler clean and prevents corrosion, but modifies the foam in such a way as to form a compact "blanket" on the water surface that filters the steam as it is produced, keeping it pure and preventing carry-over into the cylinders of water and suspended abrasive matter.

Crew

A locomotive is controlled from the backhead of the firebox and the crew is usually protected by a cab. A crew of at least two people is normally required to operate a steam locomotive. One, the driver (US: engineer), is responsible for controlling the locomotive and the fireman is responsible for the fire, steam pressure, and water.

Fittings and appliances

All locomotives are fitted with a variety of appliances. Some of these relate directly to the operation of the steam engine; while others are for signalling, train control, or other purposes. In the United States the Federal Railroad Administration mandated the use of certain appliances over the years in response to safety issues. The most typical appliances are as follows:

team pumps and injectors

Water must be forced into the boiler, to replace that which is exhausted after delivering a working stroke to the pistons. Early engines used pumps driven by the motion of the pistons. Later steam injectors replaced the pump, while some engines use turbopumps. Standard practice evolved to use two independent systems for feeding water to the boiler. Vertical glass tubes, known as water gauges or water glasses, show the level of water in the boiler.

Boiler lagging

, or wrappings of aluminium foil.

The lagging is protected by a close-fitted sheet-metal casingcite book
last=Bell |first=A Morton
date=1950
title=Locomotives
edition=seventh edition
publisher=Virtue & Co Ltd,
location=London
] known as boiler clothing or cleading.

Effective lagging is particularly important for fireless locomotives; however in recent times under the influence of L.D. Porta, "exaggerated" insulation has been practised for all types of locomotive on all surfaces liable to dissipate heat, such as cylinder ends and facings between the cylinders and the mainframes. This considerably reduces engine warmup time with marked increase in overall efficiency.

afety valves

Early locomotives were fitted with a valve controlled by a weight suspended from the end of a lever, the steam outlet being stopped by a cone-shaped valve. As there was nothing to prevent the weighted lever from bouncing when the locomotive ran over irregularities in the track, thus wasting steam, the weight was replaced by a more stable spring loaded column, often supplied by Salter, a well-known spring scale manufacturer. The danger of all these devices was that the driving crew could be tempted to add weight to the arm in order to increase pressure; most boilers were therefore from early times fitted with a tamper-proof "lockup" direct-loaded ball valve protected by a cowl. In the late 1850s, John Ramsbottom introduced an ingenious safety valve that became very popular in Britain during the latter part of the 19th Century. Not only was this valve tamper-proof, but any intervention on the part of the driver could only have the effect of easing pressure. Richardson's "pop" valve was an American invention introduced in 1867cite book
last=White |first=John H. Jr.
title=A history of the American locomotive, its development: 1830-1880
publisher=John Hopkins Press
location=Baltimore, USA
date=1968
edition=(Reprint: Dover Publications, New York 1979)
pages=pp. 146-149
] and was so designed as to release the steam only at the moment when the pressure attained the maximum permitted. This type of valve is in almost universal use at present. The British Great Western Railway was a notable exception to this rule retaining the direct loaded type until the end of its separate existence because it was considered that such a valve lost less pressure between opening and closing.

Pressure gauge

The earliest locomotives did not show the pressure of steam in the boiler, but it was possible to estimate this by the position of the safety valve arm which often extended onto the firebox back plate; gradations marked on the spring column gave a rough indication of the actual pressure. The promoters of the Rainhill trials urged that each contender have a proper mechanism for reading the boiler pressure and Stephenson devised a nine-foot vertical tube of mercury with a sight-glass at the top, mounted alongside the chimney, for the Rocket. The Bourdon tube gauge, in which the pressure straightens an oval-section, coiled tube of brass or bronze connected to a pointer, was introduced in 1849 and quickly gained acceptance. This is the device used today.cite book
last=Snell |author=John B
date=1971
title=Mechanical Engineering: Railways
publication=Longman
location=London
] Some locomotives have an additional pressure gauge in the steam chest. This helps the driver avoid wheel-slip at startup, by warning if the regulator opening is too great.

park arrestor and self cleaning smokebox

Wood-burners emit large quantities of flying sparks which necessitate an efficient spark arresting device generally mostly housed in the smokestack. Many types were fittedcite book
author=White, J |title="ibid"
pages=pp. 114-124
] , the most common early type being the Bonnet stack that incorporated a cone-shaped deflector placed before the mouth of the chimney pipe plus a wire screen covering the wide stack exit; more efficient was the Radley and Hunter centrifugal type patented in 1850, (generally known as the diamond stack) incorporating baffles so orientated as to induce a swirl effect in the chamber that encouraged the embers to burn out and fall to the bottom as ash. In the self-cleaning smokebox the opposite effect was achieved: by allowing the flue gasses to strike a series of deflector plates, angled in such a way that the blast was not impaired, the larger particles were broken into small pieces that would be ejected with the blast, rather than settle in the bottom of the smokebox to be removed by hand at the end of the run. As with the arrestor, a screen was incorporated to retain any large embers.

Locomotives of the British Railways standard classes fitted with self-cleaning smokeboxes were identified by a small cast oval plate marked "S.C.", fitted at the bottom of the smokebox door. These engines required different disposal procedures and the 'S.C.' plate highlighted this need to depot staff.

tokers

A factor that limits locomotive performance is the rate at which fuel is fed into the fire. In the early 20th century some locomotives became so large, that the fireman could not shovel coal fast enough. In the United States, various steam-powered mechanical stokers became standard equipment and were adopted and used elsewhere including Australia and South Africa.

Feedwater heating

Introducing cold water into a boiler reduces power, and from the 1920s a variety of heaters were incorporated. The most common type for locomotives was the exhaust steam feedwater heater that piped some of the exhaust through small tanks mounted on top of the boiler or smokebox or else into the tender tank; the warm water then had to be delivered to the boiler by a small auxiliary steam pump. The rare economiser type differed in that it extracted residual heat from the exhaust gases. An example of this is the pre-heater drum(s) found on the Franco-Crosti boiler.

The use of live steam and exhaust steam injectors also assists in the pre-heating of boiler feed water to a small degree, though there is no efficiency advantage to live steam injectors. Such pre-heating also reduces the thermal shock that a boiler might experience when cold water is introduced directly. This is further helped by the top feed where water is introduced to the highest part of the boiler and made to trickle over a series of trays. G.J. Churchward fitted this arrangement to the high end of his domeless coned boilers Other British lines such as the LBSCR fitted a few locomotives with the top feed inside a separate dome forward of the main one.

Condensers and water re-supply

Steam locomotives consume vast quantities of water, and supplying this was a constant logistical problem. In some desert areas, condensing engines were devised. These engines had huge radiators in their tenders and instead of exhausting steam out of the funnel it was captured and passed back to the tender and condensed. The cylinder lubricating oil was removed from the exhausted steam to avoid a phenomenon known as priming, a condition caused by foaming in the boiler which would allow water to be carried into the cylinders causing damage because of its incompressibility. The most notable engines employing condensers (Class 25C) worked across the Karoo desert of South Africa, from the 1950 until the 1980s.

Some British and American locomotives were equipped with scoops which collected water from "water troughs" (US: "track pans") while in motion, thus avoiding stops for water. In the US, small communities often did not have refilling facilities. During the early days of railroading, the crew simply stopped next to a stream and filled the tender using leather buckets. This was known as “jerking water” and led to the term "jerkwater towns" (meaning a small town, a term which today is considered derisive). cite journal
url=http://newspapers.rawson.lib.mi.us/chronicle/ccc1938%20(E)/issues/07-29-1938_3.pdf
format=PDF
title=Cass City Chronicle
journal=Cass City Chronicle
date=Friday, July 29, 1938
pages=p 3
accessdate=2007-09-26
] In Australia and South Africa, locomotives in drier regions operated with large oversized tenders and some even had an additional water wagon, sometimes called a "canteen" or in Australia (particularly in New South Wales) a "water gin".

Steam locomotives working on underground railways (such as London's Metropolitan Railway) were fitted with condensing apparatus for a different, but obvious, reason. These were still being used between King's Cross and Moorgate into the early 1960s.

Braking

Locomotives have their own braking system, independent from the rest of the train. Locomotive brakes employ large shoes which press against the driving wheel treads. With the advent of air brakes, a separate system also allowed the driver to control the brakes on all cars. These systems require steam-powered pumps, which are mounted on the side of the boiler or on the smokebox front. Such systems operated in the United States, Canada, Australia and New Zealand.

An alternative to the air brake is the vacuum brake. Where vacuum brakes are used, a steam-operated ejector is mounted on the engine instead of the air pump. A secondary ejector or crosshead vacuum pump is used to maintain the vacuum in the system. Vacuum systems existed on British, Indian and South African rail networks.

Steam locomotives are nearly always fitted with sandboxes from which sand can be delivered to the rails to improve traction and braking in wet or icy weather. On American locomotives the sandboxes, or sand domes, are usually mounted on top of the boiler. In Britain, the limited loading gauge precludes this, so the sandboxes are mounted just above, or just below, the running plate.

Lubrication

.cite web
url=http://www.cr.nps.gov/history/online_books/railroad/shs2b.htm
publisher=U.S. National Parks Service online history resource
title=Pennsylvania Railroad chemical laboratory
accessdate=2006-11-09
]

As speeds and distances increased, mechanisms were developed that injected thick mineral oil into the steam supply. The first, a displacement lubricator, mounted in the cab, uses a controlled stream of steam condensing into a sealed container of oil. Water from the condensed steam displaces the oil into pipes. The apparatus is usually fitted with sight-glasses to confirm the rate of supply. A later method uses a mechanical pump worked from one of the crossheads. In both cases, the supply of oil is proportional to the speed of the locomotive.

are trailed from oil reservoirs into pipes leading to the respective component.cite book
date=1957
title=Handbook for Railway Steam Locomotive Enginemen
publisher=British Transport Commission
] The rate of oil supplied is controlled by the size of the bundle of yarn and not the speed of the locomotive, so it is necessary to remove the trimmings (which are mounted on wire) when stationary. However, at regular stops (such as a terminating station platform) oil finding its way onto the track can still be a problem.

Crank pin and crosshead bearings carry small cup-shaped reservoirs for oil. These have feed pipes to the bearing surface that start above the normal fill level, or are kept closed by a loose-fitting pin, so that only when the locomotive is in motion does oil enter. In United Kingdom practice the cups are closed with simple corks, but these have a piece of porous cane pushed through them to admit air. It is customary for a small capsule of pungent oil (aniseed or garlic) to be incorporated in the bearing metal to warn if the lubrication fails and excess heating or wear occurs.

Buffers

In British practice, the locomotive usually had buffers at each end to absorb compressive loads ("buffets""Oxford English Dictionary": Buff 1] ). The tensional load of drawing the train (draft force) is carried by the coupling system. Together these control slack between the locomotive and train, absorb minor impacts, and provide a bearing point for pushing movements.

In American practice all of the forces between the locomotive and cars are handled through the coupler and its associated draft gear, which allows some limited slack movement. Small dimples called "poling pockets" at the front and rear corners of the locomotive allowed cars to be pushed on an adjacent track using a pole braced between the locomotive and the cars.

Pilots

A pilot was usually fixed to the front end of locomotives, although in European and a few other railway systems, such as New South Wales, they were considered unnecessary. Plough-shaped, and called cow catchers, they were quite large and were designed to remove obstacles from the track such as cattle, bison, other animals or tree limbs. Though unable to "catch" stray cattle these distinctive items remained on locomotives until the end of steam. Switching engines usually replaced the pilot with small steps. Many systems used the pilot and other design features to produce a distinctive appearance.

Headlights

lamps, but when electric lights became available in the late 1880s, they quickly replaced the older types.

Britain used low intensity oil lamps and were not intended to allow the driver to see the way ahead (locomotive drivers were expected to have sufficient route knowledge) but were used to indicate the class of a train by their position on the front of the locomotive. Four lamp irons were provided: one below the chimney and three evenly spaced across the top of the buffer beam. The exception to this was the Southern Railway and its constituents, who added two lamp irons one each side of the smokebox, and the arrangement of lamps (or in daylight white circular plates) told railway staff the origin and destination of the train.

In some countries heritage steam operation continues on the national network. Some railway authorities have mandated powerful headlights on at all times, including during daylight. This was to further inform the public or track workers of any active trains.

Bells and whistles

Locomotives used bells and steam whistles from earliest days. In the United States, India and Canada bells warned of a train in motion. In Britain, where all lines are by law fenced throughout,cite book
section=Section 10
title=Railway Regulation Act
date=1842
publisher=Her Majesty's Stationery Office
] bells were only a requirement on railways running on a road (i.e. not fenced off), for example a tramway along the side of the road or in a dockyard. Consequently only a minority of locomotives in the UK carried bells. Whistles are used to signal personnel and give warnings. Depending on the terrain the locomotive was being used in the whistle could be designed for long distance warning of impending arrival, or more for localised use.

Early bells and whistles were sounded through pull-string cords and levers. As the steam era approached the 1950s, automatic air-operated bells were made use of on locomotives such as the Challenger (steam locomotive) and Big Boy.

Automatic Train Control

From early in the twentieth century operating companies in such countries as Germany and Britain began to fit locomotives with in-cab signalling which automatically applied the brakes when a signal was passed at "caution". In Britain these became mandatory in 1956.

Booster engines

In the United States and Australia the trailing truck was often equipped with an auxiliary steam engine which provided extra power for starting. This booster engine was set to cut out automatically at a certain speed. On the narrow gauged New Zealand railway system, six Kb 4-8-4 locomotives had boosters; the only RailGauge|42 gauge engines in the world to have such equipment.

Variations

Numerous variations to the simple locomotive occurred as railways attempted to develop more powerful, more efficient and fast steam locomotives.

Cylinders

Some locomotives received extra cylinders and experiments combined two locomotives in one (e.g. the Mallet and Garratt locomotives). Some locomotives carried their cylinders vertically alongside the boiler and drove the wheels through a system of shafts and gears (e.g. the Shay locomotive; see "geared steam locomotive").

From about 1930, most new British express passenger locomotives were 4-6-0 or 4-6-2 types with three or four cylinders. Examples include:

* GWR 4073 Class, four-cylinder 4-6-0
* LNER Class A1/A3, three-cylinder 4-6-2

Cab forward

In the United States on the Southern Pacific Railroad a series of cab forward locomotives had the cab and the firebox at the front of the locomotive and the tender behind the smokebox, so that the engine appeared to run backwards. This was only possible by using oil-firing. Southern Pacific selected this design to provide smoke-free breathing for the locomotive's engineer as they went through the SP's numerous mountain tunnels and snow sheds. Another variation was the Camelback locomotive with the cab half-way along the boiler.

team turbines

Steam turbines were one of the experiments in improving the operation and efficiency of steam locomotives. Experiments with steam turbines using direct-drive and electrical transmissions, in different countries, proved mostly unsuccessful. The LMS also built Turbomotive, a largely successful attempt to prove the efficiency of steam turbines. Had it not been for the outbreak of WW2, more may have been built. The Turbomotive ran from 1935-49, when it was rebuilt into a conventional locomotive because replacement of many parts was required, an uneconomical proposition for a 'one-off' locomotive. In the United States the Union Pacific, Chesapeake and Ohio, and Norfolk & Western railways all built turbine-electric locomotives. The Pennsylvania Railroad (PRR) also built turbine locos but with a direct-drive gearbox. However, all designs failed due to dust, vibration, design flaws, or inefficiency below speed. The last one in service was the N&W's being retired in January 1958.

Valve gear

Numerous technological advances improved the steam engine. Early locomotives used simple valve gear that gave full power in either forward or reverse. Soon Stephenson valve gear allowed the driver to control cut-off; this was largely superseded by Walschaerts valve gear and similar patterns. Early locomotive designs using slide valves and outside admission were easy to construct, but inefficient and prone to wear. Eventually, slide valves were superseded by inside admission piston valves, though there were attempts to apply poppet valves (common by then on stationary engines) in the 20th century. Stephenson valve gear was generally placed within the frame and was difficult to access for maintenance; later patterns applied outside the frame, were readily visible and maintained.

Compounding

From 1876, compound locomotives came on the scene, which used the engine's steam twice. There were many compound locomotives especially where long periods of continuous efforts were needed. Compounding was an essential ingredient of the quantum leap in power achieved by André Chapelon's rebuilds from 1929. A common application was to articulated locomotive, the most common being that of Anatole Mallet in which the high pressure stage was attached directly to the boiler frame; in front of this was pivoted a low pressure engine on its own frame, taking the exhaust from the rear engine. cite book
last=Van Riemsdijk |first=John T.
title=Compound locomotives, an international survey
publisher=Atlantic Transport Publishers
location=Penryn, England
date=1994
isbn=0 906899 61 3
]

Articulated and Duplex types

Articulation itself proved very popular, and there were numerous variations, both compound and simple. Duplex locomotives with two engines in one rigid frame were also tried, but were not notably successful. For example, the 4-4-4-4 Pennsylvania Railroad's T1 class, designed for very fast running, suffered incurable slippage problems throughout their careers. [David Ross, "The Steam Locomotive: a History", Tempus Publishing, Gloucestershire, 2006, ISBN 0-7524-3916-2]

Hybrid power

Main|Steam diesel hybrid locomotive‎ Mixed power locomotives, utilising steam and diesel propulsion, have been produced in Russia, Britain and Italy.

Manufacture

United States

With the notable exception of the USRA standard locomotives, set during World War 1, in the United States, steam locomotive manufacture was always customised. Railroads ordered locomotives tailored to their specific requirements, though basic similarities were always present. Railroads developed specific characteristics; for example, the Pennsylvania Railroad had a preference for the Belpaire firebox, [http://www.everything2.com/index.pl?node_id=1424086 Pennsylvania Railroad locomotive classification@Everything2.com ] ] while the Delaware and Hudson Railroad was famous for its elaborately flanged smokestacks.Fact|date=February 2007 In the United States, specialised manufacturers constructed locomotives for all rail companies, although all railroads had shops capable of heavy repairs and some railroads (for example the Norfolk and Western Railway) constructed locomotives in their own shops. Companies Manufacturing locomotives in the US included Baldwin Locomotive Works, American Locomotive Works (ALCO), Lima Locomotive Works, and others. It was not uncommon for an entire group of locomotives to be sold from one railroad to another.Fact|date=February 2007

Steam locomotives required regular service and overhaul (often at government-regulated intervals). Many alterations occurred during overhauls. New appliances were added, unsatisfactory features removed, cylinders improved or replaced. Any part of the locomotive, including boilers were replaced or upgraded. On the Baltimore and Ohio Railroad two 2-10-2 locomotives were dismantled; the boilers were placed onto two new Class T 4-8-2 locomotives and the residue wheel machinery made a pair of Class U 0-10-0 switchers with new boilers. Union Pacific's fleet of 3 cylinder 4-10-2 engines were converted into two cylinder engines in 1942, because of high maintenance problems.

United Kingdom

Before the 1923 Grouping, the picture in the UK was mixed. The larger railway companies built locomotives in their own workshops but the smaller ones and industrial concerns ordered them from outside builders. A large market for outside builders was abroad because of the home-build policy exercised by the main railway companies.

Between 1923 and 1947, the "Big Four" railway companies (the Great Western Railway, the London, Midland and Scottish Railway, the London and North Eastern Railway and the Southern Railway) all built most of their own locomotives. Generally speaking, they only bought locomotives from outside builders when their own works were fully occupied (or as a result of government-mandated standardisation during wartime).

From 1948, British Railways allowed the former "Big Four" companies (now designated "Regions") to continue to build their own designs, but also created a range of "standard" locomotives which supposedly combined the best features from each region. Although a policy of "dieselisation" was adopted in 1955, BR continued to build new steam locomotives until 1960 (the last being named "Evening Star").

Some independent manufacturers produced steam locomotives for a few more years, the last British-built industrial steam locomotive being constructed by Hunslet in 1971. Since then, a few specialised manufacturers have continued to produce small locomotives for narrow gauge and miniature railways, but as the prime market for these is the tourist and heritage railway sector, the demand for such locomotives is limited.

Australia

In Australia, Clyde Engineering of Sydney and also the Eveleigh Workshops built steam locomotives for the New South Wales Government Railways. These include the C38 class 4-6-2, the first five were build at Clyde with streamlining, the other 25 locomotives were built at Eveleigh (13) in Sydney, and Cardiff Workshops (12) near Newcastle. In Queensland, steam locomotives were locally constructed by Walkers. Similarly the South Australian state government railways also manufactured steam locomotives locally at Islington in Adelaide. The Victorian Railways constructed most of their locomotives at their Newport Workshops and Bendigo while in the early days locomotives were built in Ballarat. Locomotives constructed at the Newport shops ranged from the nA class 2-6-2T built for the narrow gauge, up to the H class 4-8-4, the largest conventional locomotive ever to operate in Australia, which weighed 260 tons. However, the title of largest locomotive in Australia goes to the 263 ton NSWGR AD60 class 4-8-4+4-8-4 Garratt (Oberg:1975), which were built by Beyer-Peacock in the United Kingdom.

Categorisation

.

The Whyte notation, used in most English speaking and Commonwealth countries, represents each set of wheels with a number. Different arrangements were given names which usually reflect the first usage of the arrangement; for instance the "Santa Fe" type (2-10-2) is so called because the first examples were built for the Atchison, Topeka and Santa Fe Railroad. These names were informally given and varied according to region and even politics.

The UIC classification is used mostly in European countries apart from the United Kingdom. It designates consecutive pairs of wheels (informally "axles") with a number for non-driving wheels and a capital letter for driving wheels (A=1, B=2 etc). So a Whyte 4-6-2 designation would be an equivalent to a 2-C-1 UIC designation.

On many railroads, locomotives were organised into classes. These broadly represented locomotives which could be substituted for each other in service, but most commonly a class represented a single design. As a rule classes were assigned some sort of code, generally based on the wheel arrangement. Classes also commonly acquired nicknames representing notable (and sometimes uncomplimentary) features of the locomotives.Fact|date=February 2007

Performance

Measurement

In the steam locomotive era, two measures of locomotive performance were generally applied. At first, locomotives were rated by tractive effort This can be roughly calculated by multiplying the total piston area by 85% of the boiler pressure (a rule of thumb reflecting the slightly lower pressure in the steam chest above the cylinder) and dividing by the ratio of the driver diameter over the piston stroke. However, the precise formula is:

"Tractive Effort" is defined as the average force developed during one revolution of the driving wheels at the rail head.cite book |last= Swengel |first=Frank M |authorlink= |coauthors= |title=The American Steam Locomotive, Vol.1, The Evolution of the Steam Locomotive |year= 1967|publisher= MidWest Rail Publications|location= Davenport, IA|isbn= ] This is expressed as:

:t = frac {cPd^2s} {D}.

where d is bore of cylinder (diameter) in inches,s is cylinder stroke, in inches,P is boiler pressure in pound per square inch,D is driving wheel diameter in inches,c is the effective cut-off.cite book
last =Adams
first =Henry
authorlink =
coauthors =
title =Cassell's Engineer's Handbook
publisher =Cassell and Company
date= 1908
location =London
pages = p389
url =
doi =
id =
isbn =
]

It is critical to appreciate the use of the term 'average', as not all effort is constant during the one revolution of the drivers for at some points of the cycle only one piston is exerting turning moment and at other points both pistons are working. Not all boilers deliver full power at starting and also the tractive effort decreases as the rotating speed increases.

Tractive effort is a measure of the heaviest load a locomotive can start or haul at very low speed over the ruling grade in a given territory.

However, as the pressure grew to run faster freight and heavier passenger trains, tractive effort was seen to be an inadequate measure of performance because it did not take into account speed.

Therefore in the 20th century, locomotives began to be rated by power output. A variety of calculations and formulas were applied, but in general railroads used dynamometer cars to measure tractive force at speed in actual road testing. This measure was termed drawbar horsepower in the United States and remained the standard measure of performance to the end of mainline usage.Fact|date=February 2007

British railway companies have been reluctant to disclose figures for drawbar horsepower and have usually relied on continuous tractive effort instead.

Relation to wheel arrangement

Whyte classification is connected to locomotive performance, but through a somewhat circuitous path. Given adequate proportions of the rest of the locomotive, power output is determined by the size of the fire, and for a bituminous coal-fuelled locomotive, this is determined by the grate area. Modern non-compound locomotives are typically able to produce about 40 drawbar horsepower per square foot of grate. Tractive force, as noted earlier, is largely determined by the boiler pressure, the cylinder proportions, and the size of the driving wheels. However, it is also limited by the weight on the driving wheels (termed adhesive weight), which needs to be at least four times the tractive effort.

The weight of the locomotive is roughly proportional to the power output; the number of axles required is determined by this weight divided by the axleload limit for the trackage where the locomotive is to be used. The number of driving wheels is derived from the adhesive weight in the same manner, leaving the remaining axles to be accounted for by the leading and trailing bogies. Passenger locomotives conventionally had two-axle leading bogies for better guidance at speed; on the other hand, the vast increase in the size of the grate and firebox in the 20th century meant that a trailing bogie was called upon to provide support. On the European continent, some use was made of several variants of the "Bissel bogie" in which the swivelling movement of a single axle truck controls the lateral displacement of the front driving axle (and in one case the second axle too). This was mostly applied to 8-coupled express and mixed traffic locomotives and considerably improved their ability to negotiate curves whilst restricting overall locomotive wheelbase and maximising adhesion weight.

As a rule, "shunting engines" (US "switching engines") omitted leading and trailing bogies, both to maximise tractive effort available and to reduce wheelbase. Speed was unimportant; making the smallest engine (and therefore smallest fuel consumption) for the tractive effort paramount. Driving wheels were small and usually supported the firebox as well as the main section of the boiler. Banking engines (US "helper engines") tended to follow the principles of shunting engines, except that the wheelbase limitation did not apply, so banking engines tended to have more driving wheels. In the US, this process eventually resulted in the Mallet type with its many driven wheels, and these tended to acquire leading and then trailing bogies as guidance of the engine became more of an issue.

As locomotive types began to diverge in the late 1800s, freight engine designs at first emphasised tractive effort, whereas those for passenger engines emphasised speed. Over time, freight locomotive size increased, and the overall number of axles increased accordingly; the leading bogie was usually a single axle, but a trailing truck was added to larger locomotives to support a larger firebox that could no longer fit between or above the driving wheels. Passenger locomotives had leading bogies with two axles, fewer driving axles, and very large driving wheels in order to limit the speed at which the reciprocating parts had to move.

In the 1920s the focus in the United States turned to horsepower, epitomised by the "super power" concept promoted by the Lima Locomotive Works, although tractive effort was still the prime consideration after World War One to the end of steam. Freight trains were to run faster; passenger locomotives needed to pull heavier loads at speed. In essence, the size of grate and firebox increased without changes to the remainder of the locomotive, requiring the addition of a second axle to the trailing truck. Freight 2-8-2s became 2-8-4s while 2-10-2s became 2-10-4s. Similarly, passenger 4-6-2s became 4-6-4s. In the United States this led to a convergence on the dual-purpose 4-8-4 and the 4-6-6-4 articulated configuration, which was used for both freight and passenger service.cite book
last=Allen |first=Cecil J
date=1949
title=Locomotive Practice and Performance in the Twentieth Century
publisher=W Heffer and Sons Ltd |location=Cambridge, England
] Mallet locomotives went through a similar transformation and evolved from bank engines into huge mainline locomotives with gargantuan fireboxes; their driving wheels being increased in size in order to allow faster running.

The end of steam in general use

The introduction of electric locomotives at the turn of the 20th century spelled the beginning of the end for steam locomotives, although that end was long in coming. As Diesel power, more especially with electric transmission, became more reliable in the 1930s it gained a foothold in North America cite web
url=http://mikes.railhistory.railfan.net/r085.html
title=1935 article on the advantages of diesel locomotives
] . The full changeover took place there during the 1950s. In continental Europe large-scale electrification had displaced steam power by the 1970s, Steam had in its favour familiar technology and adapted well to local facilities and consume a wide variety of fuels; this led to its continued use in many countries to the end of the 20th Century. They have considerably less thermal efficiency than modern diesels, requiring constant maintenance and labour to keep them operational. Water is required at many points throughout a rail network and becomes a major problem in desert areas, as are found in some regions within the United States, Australia and South Africa. In other localities the local water is unsuitable. The reciprocating mechanism on the driving wheels of a two-cylinder single expansion steam locomotive tended to pound the rails (see "hammer blow"), thus requiring more maintenance. Raising steam from coal took a matter of hours which brought serious pollution problems. Coal-burning locomotives required fire cleaning and ash removal between turns of duty. This was all done in the open air by hand in deplorable working conditions. Diesel or electric locomotives, by comparison, drew benefit from new custom built servicing facilities. Finally, the smoke from steam locomotives was deemed objectionable; in fact, the first electric and diesel locomotives were developed to meet smoke abatement requirementscite book
title=Diesel Traction Manual for Enginemen
pages=pp. 15-16
publisher=British Transport Commission
date=1962
] although this did not take into account the high level of invisible pollution in diesel exhaust smoke especially when idling. It should also be remembered that the power for most electric trains is, in fact, derived from steam, generated in a power station.

United States

mill in Sterling, IL, continued to operate steam locomotives until December 1980.cite web
url=http://www.lib.niu.edu/ipo/1981/ip810512.html
title=Last locomotive to operate in the United States
publisher=Library Service of Northern Illinois University
accessdate=2007-11-05
]

United Kingdom

Trials of diesel locomotives and railcars began in the United Kingdom in the 1930s but made only limited progress. One problem was that British diesel locomotives were often seriously under-powered, compared with the steam locomotives against which they were competing.

After 1945, problems associated with post-war reconstruction and the availability of cheap domestic-produced coal kept steam in widespread use throughout the two following decades. However the ready availability of cheap oil led to new dieselisation programmes from 1955 and these began to take full effect from around 1962. Towards the end of the steam era, which came about in 1968, steam motive power was allowed to fall into a dire state of repair; this along with the absence of attention given to the attendant staff working conditions could only accelerate the decline to such a degree that British Railways estimated that its steam locomotives accounted for around four times more in running costs than diesels.Fact|date=February 2007 The use of steam locomotives in British industry continued on an ever-reducing scale into the late 1980sFact|date=February 2007, but the poor availability of replacement parts, coupled with the decline of the coal mining industry, led to the disappearance of steam power for commercial uses.

outh Korea

In South Korea, the first steam locomotive was the Moga (Mogul?) 2-6-0, followed by; Sata, Pureo, Ame, Sig, Mika, Pasi, Hyeogi, Class 901, Mateo, Sori, and Tou. Used until 1967, that locomotive is now in the Railroad Museum.

Other countries

In other countries, the conversion from steam was slower. By March 1973 in Australia, steam had vanished in all states. Diesel locomotives were more efficient and the demand for manual labour for service and repairs was less than steam. Cheap oil had cost advantages over coal.

In the USSR, the last steam locomotive (model П36, serial number 251) was built in 1956; now in the Museum of Railway Machinery at former Warsaw Rail Terminal, Saint Petersburg, Russia. In the European part of the USSR, almost all steam locomotives were replaced by diesel and electrical ones in 1960s; in Siberia with its cheap coal, steam locomotives were in active use till mid-1970s. However, some photographs exist of Russian steam locomotives at work into the 1980s, and many accurate historical records state that Russian Decapods, L-class 2-10-0s, and LV-class 2-10-2s were retired between 1980-1985, implying that the best of Russian steam, such as the P36 class, remained on the active rosters into the 1990s. Until 1994, Russia had at least 1,000 steam locomotives stored in operable condition in case of "national emergencies" - as a result, more than 200 steam locomotives are still in working condition.Fact|date=November 2007

In Finland, the first diesels were introduced in the mid-1950s and they superseded the steam locomotives during the early '60s. The State Railways (VR) operated steam locomotives until 1975.

In Poland, on non-electrified tracks steam locomotives were superseded almost entirely by diesels by the early '90s. A few steam locomotives, however, operate still from Wolsztyn. Although they are maintained operational rather as a means of preserving railway heritage and as a tourist attraction, they do haul regular scheduled trains (mostly to Poznań). Apart from that, numerous railway museums and heritage railways (mostly narrow gauge) own steam locomotives in working condition.

In India steam locomotives were in use until 1989; they were replaced by a combination of diesel and electric locomotives. Steam locomotives from India were then sold to an undisclosed African country.Fact|date=July 2008 A steam locomotive celebration run was organised between Thane and Mumbai to commemorate the 150th year of railways in India.

In South Africa an oil embargo combined with an abundance of cheap local coal and a cheap labour force, ensured steam locomotives survived into the 1990s.Fact|date=February 2007 Locomotive engineer L. D. Porta's designs appeared on a Class 19D engine in 1979, then a former Class 25 4-8-4 engine, became a Class 26, termed the "Red Devil" No. 3450, which demonstrated an improved overall performance with decreased coal and water consumption. The single class 26 locomotive operated until the end of steam. Another class 25NC locomotive, No. 3454, nicknamed the "Blue Devil" because of its colour scheme, received modifications including a most obvious set of double side-by-side exhaust stacks. In southern Natal, two former South African Railway RailGauge|2ft gauge NGG16 Garratts operating on the privatised Port Shepstone & Alfred County Railway (ACR) received some L. D. Porta modifications in 1990 becoming a new NGG16A class. VidRail Productions, South African end of Steam: "Orange Free State, Part 4, Vols. 3, 4 and 5" and "Natal, Part 3, Vol. 1", in "The Best of Southern African Steam, 1983-1990"]

China continued to build mainline steam locomotives until late in the century, even building a few examples for American tourist operations. Since China was the last main-line user of steam locomotives, ending officially at the beginning of 2006, it is plausible that many still exist in industrial operations or in more remote parts of China. Many coal mines and smaller cities, such as Pingdingshan and Hegang, maintain an active roster of JS, SY, or QJ steam locomotives bought secondhand from China Rail. The last steam locomotives built in China were of the SY 2-8-2 class, built until 1999.Fact|date=November 2007 The last steam locomotive built in China was SY 1772, finished in 1999. As of 2007, at least four Chinese steam locomotives exist in the United States - 2 QJ's bought by RDC, a JS bought by the Boone Scenic Railway, and an SY bought by the NYSW for tourist operations, but re-painted and modified to represent a 1920s era US locomotive.

Pakistan is currently the only country where there is still a regular steam locomotive service; a line operates in the Northwest Frontier Province and Sindh; It has been preserved as a "nostalgia" service for tourism in exotic locales [http://pakrail.com/steam.asp] , indeed it is specifically advertised as being for "steam buffs" [http://pakrail.com/steam.asp]

Hopes of revival

Dramatic increases in the cost of diesel fuel prompted several initiatives to revive steam power. [cite web |url=http://www.5at.co.uk/ |title=The 5AT project to develop a modern steam locomotive for British railways] [cite web |url=http://www.martynbane.co.uk/modernsteam/smcmahon/rfirt/aug06news.htm |title=Railway Extension Across the Andes: reactivation and modernisation of existing fleet of 75 cm gauge 2-10-2 steam locomotives] None of these has progressed to the point of production, and in the early 21st century, the steam locomotives operate only in a few isolated regions and in tourist operations.

In Germany a small number of fireless steam locomotives are still working in industrial service, e.g. at power stations.

The Swiss company Dampflokomotiv und Maschinenfabrik DLM AG delivered several new steam locomotives to rack railways in Switzerland and Austria between 1992 and 1996. One was the Brienz Rothorn Bahn.

Several heritage railways in the United Kingdom have built new steam locomotives in the 1990s and early 2000s. These include the narrow gauge Ffestiniog and Corris railways in Wales. The Hunslet Engine Company was revived in 2005 and is now building steam locomotives on a commercial basis. [cite web|url=http://www.hunsletengine.com/hsc/index.php|title=About Huslet Steam Co|last=Staff|publisher=Hunslet Hunslet Engine Company|accessdate=2008-08-04] A standard gauge LNER Peppercorn Pacific "Tornado" was completed at Hopetown Works, Darlington, England and made its first run on 1 August 2008. [cite news|url=http://www.darlingtonandstocktontimes.co.uk/display.var.2416232.0.newlybuilt_steam_loco_takes_to_the_tracks.php|title=Newly-built steam loco takes to the tracks|last=Roberts|first=David|date=2008-08-03|work=Darlington and Stockton Times|accessdate=2008-08-04] [cite web|url=http://www.bbc.co.uk/tees/content/articles/2007/12/03/a1_tornado_feature.shtml|title=60163 Tornado is on the go|last=Staff|date=2008-09-22|publisher=BBC Tees|accessdate=2008-10-01] It will enter mainline service later in 2008, with demonstration trips in France and Germany planned. [cite news|url=http://www.guardian.co.uk/travel/2008/aug/02/railtravel.heritage|title=New steam locomotive unveiled|last=Glancy|first=Jonathan|date=2008-08-02|work=The Guardian|accessdate=2008-08-04]

team locomotives in numismatics

Steam locomotives have left such a legacy behind, that they have been the main topic for numerous collectors and bullion coins. On of the most recent ones is the famous 20 euro Biedermeier Period coin, minted in June 11 2003. The obverse of the coin shows a premature steam locomotive (the AJAX) on Austria's first railway line, the Kaiser Ferdinand's Nordbahn. The AJAX can still be seen today in the Austrian railway museum.

References

ee also


* Beyer-Garratt
* BNSF
* Dieselization
* Electrification
* Firetube boiler
* Geared steam locomotive
* High pressure steam locomotive
* History of rail transport
* Invicta (locomotive)
* John Bull (locomotive) oldest operable steam locomotive in the world
* List of heritage railways
* Live steam
* LMR 57 Lion Britain's oldest operable steam locomotive
* Locomotion No 1
* Locomotive
* Montreal Locomotive Works
* Novelty (locomotive)
* New York Central's Niagara 'S1" class (contains tabulated form of results from NYC 1946 steam versus diesel trials)
* Steam turbine locomotive
* Steam dummy
* Steam engine
* Steam locomotive components (contains detailed explanatory diagrams)
* Steam locomotive production
* Stephenson's Rocket

Manufacturers

* Beyer Peacock
* Neilson and Company

External links

* [http://commons.wikimedia.org/wiki/Category:671 GKB 671: The longest serving steam locomotive in the world (since 1860)]
* [http://www.steamlocomotive.com/ Database of surviving steam locomotives in North America]
* [http://steamrailroading.com/ Information on North American steam railroads in operation]
* [http://www.heritagerailways.com/ UK heritage railways and preserved locomotives database]
* [http://railways.national-preservation.com/ National Preservation. Uk's leading forum on UK heritage railways]
* [http://www.5at.co.uk/ Pages for the British project to build a modern steam locomotive. The Advanced Steam Locomotive. (5AT)]
* [http://www.steam.dial.pipex.com/ International Steam Locomotives]
* [http://www.virtualmuseum.ca/pm.php?id=story_line&lg=English&fl=0&ex=00000092&sl=2930&pos=1 Tracks of Time]

Further reading

Many thousands of books about steam locomotives have been published, particularly since railway companies have turned to alternative forms of propulsion. The following is a list of earlier books that may be of use for serious research.

* C. E. Wolff, "Modern Locomotive Practice: A Treatise on the Design, Construction, and Working of Steam Locomotives" (Manchester, England, 1903)
* Henry Greenly, "Model Locomotive" (New York, 1905)
* G. R. Henderson, "Cost of Locomotive Operation" (New York, 1906)
* W. E. Dalby, "Economical Working of Locomotives" (London, 1906)
* A. I. Taylor, "Modern British Locomotives" (New York, 1907)
* E. L. Ahrons, "The Development of British Locomotive Design" (London, 1914)
* E. L. Ahrons, "Steam Engine Construction and Maintenance" (London, 1921)
* J. F. Gairns, "Locomotive Compounding and Superheating" (Philadelphia, 1907)
* Angus Sinclair, "Development of the Locomotive Engine" (New York, 1907)
* Vaughn Pendred, "The Railway Locomotive, What it is and Why it is What it is" (London, 1908)
* Brosius and Koch, "Die Schule des Lokomotivführers" (thirteenth edition, three volumes, Wiesbaden, 1909-1914)
* G. L. Fowler, "Locomotive Breakdowns, Emergencies, and their Remedies" (seventh edition, New York, 1911)
* Fisher and Williams, "Pocket Edition of Locomotive Engineering" (Chicago, 1911)
* T. A. Annis, "Modern Locomotives" (Adrian Michigan, 1912)
* C. E. Allen, "Modern Locomotive" (Cambridge, England, 1912)
* W. G. Knight, "Practical Questions on Locomotive Operating" (Boston, 1913)
* G. R. Henderson, "Recent Development of the Locomotive" (Philadelphia, 1913)
* Wright and Swift (editors) "Locomotive Dictionary" (third edition, Philadelphia, 1913)
* Roberts and Smith, "Practical Locomotive Operating" (Philadelphia, 1913)
* E. Prothero, "Railways of the World" (New York, 1914)
* M. M. Kirkman, "The Locomotive" (Chicago, 1914)
* C. L. Dickerson, "The Locomotive and Things You Should Know About it" (Clinton, Illinois, 1914)
* P. W. B. Semmens, A. J. Goldfinch, "How Steam Locomotives Really Work" (Oxford University Press, USA, 2004) ISBN 0-19-860782-2
* Gerald A Dee, "A Lifetime of Railway Photography" in "Photographer Profile", Train Hobby Publications, Studfield, 1998. (Australian steam)
* Leon Oberg, "Locomotives of Australia," Reed, Sydney, 1975.
* Swengel, F. M. "The American Steam Locomotive; Vol. 1. The Evolution of the American Steam Locomotive", Midwest Rail Publication, Iowa, 1967.


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • steam locomotive — noun a locomotive powered by a steam engine • Hypernyms: ↑locomotive, ↑engine, ↑locomotive engine, ↑railway locomotive • Part Meronyms: ↑firebox, ↑steam engine * * * noun …   Useful english dictionary

  • steam locomotive — garvežys statusas T sritis Energetika apibrėžtis Garo mašinos varomas lokomotyvas. Jį sudaro garo katilas ir garo mašina, kuriuos, kaip savaeigę sistemą, jungia bendra konstrukcija. atitikmenys: angl. steam locomotive vok. Dampflokomotive, f rus …   Aiškinamasis šiluminės ir branduolinės technikos terminų žodynas

  • Steam locomotive components — A listing of the components typically found on Steam locomotives.Guide to steam locomotive components (The image is of a composite imaginary locomotive, not all components are present on all locomotives and not all possible components are present …   Wikipedia

  • Steam locomotive condensing apparatus — A steam locomotive condensing apparatus differs in purpose from the usual closed cycle steam engine condenser, in that its function is primarily either to recover water, or to avoid excessive emissions to the atmosphere, rather than maintaining a …   Wikipedia

  • steam locomotive — noun A locomotive, usually for use on a railway, that is powered by steam. Syn: steam engine, pufferbelly …   Wiktionary

  • steam locomotive — a locomotive moved by steam power generated in its own boiler: still in commercial use in nations that have not yet converted entirely to diesel and electric locomotives. See table under Whyte classification. * * * …   Universalium

  • Steam locomotive production — North America = Early 20th Century Early 20th Century locomotive production in the USA included units made for both domestic and export markets. Foreign market production increased significantly during and immediately after World War I. In the… …   Wikipedia

  • steam locomotive — Richard Trevithick …   Inventors, Inventions

  • Meiningen Steam Locomotive Works — The Meiningen Steam Locomotive Works (German: Dampflokwerk Meiningen) is a railway repair shop in Meiningen, Germany. It is owned by Deutsche Bahn and has specialised in the maintenance of museum steam locomotives since 1990, having extensive… …   Wikipedia

  • Geared steam locomotive — A geared steam locomotive is a type of steam locomotive which uses reduction gearing in the drivetrain, as opposed to the common directly driven design.The locomotives use conventional adhesion to provide traction and therefore should not be… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”